Engineering topics
Liu, Feng
Publications and source records attributed to Liu, Feng.
Quantum spin Hall phase in 2D trigonal lattice
The quantum spin Hall (QSH) phase is an exotic phenomena in condensed-matter physics. Here we show that a minimal basis of three orbitals (s, p x , p y ) is required to produce a QSH phase via nearest-neighbour hopping in a two-dimensional trigonal lattice. Tight-binding model analyses and calculations show that the QSH phase arises from a spin–orbit coupling (SOC)-induced s–p band inversion or p–p bandgap opening at Brillouin zone centre (Γ point), whose topological phase diagram is mapped out in the parameter space of orbital energy and SOC. Remarkably, based on first-principles calculations, this exact model of QSH phase is shown to be realizable in an experimental system of Au/GaAs(111) surface with an SOC gap of ~73 meV, facilitating the possible room-temperature measurement. Finally, our results will extend the search for substrate supported QSH materials to new lattice and orbital types.
High-performance polyimide nanocomposites with core-shell AgNWs@BN for electronic packagings
The increasing density of electronic devices underscores the need for efficient thermal management. Silver nanowires (AgNWs), as one-dimensional nanostructures, possess a high aspect ratio and intrinsic thermal conductivity. However, high electrical conductivity of AgNWs limits their application for electronic packaging. We synthesized boron nitride-coated silver nanowires (AgNWs@BN) using a flexible and fast method followed by incorporation into synthetic polyimide (PI) for enhanced thermal conductivity and dielectric properties of nanocomposites. The thinner boron nitride intermediate nanolayer on AgNWs not only alleviated the mismatch between AgNWs and PI but also enhanced their interfacial interaction. Hence, the maximum thermal conductivity of an AgNWs@BN/PI composite with a filler loading up to 20% volume was increased to 4.33 W/m K, which is an enhancement by nearly 23.3 times compared with that of the PI matrix. The relative permittivity and dielectric loss were about 9.89 and 0.015 at 1 MHz, respectively. Compared with AgNWs@SiO{sub 2}/PI and Ag@BN/PI composites, boron nitride-coated core-shell structures effectively increased the thermal conductivity and reduced the permittivity of nanocomposites. The relative mechanism was studied and discussed. This study enables the identification of appropriate modifier fillers for polymer matrix nanocomposites.
Direction-Controlled Light-Driven Movement of Microribbons
Novel direction-controlled movements of microribbons self-assembled from perylene diimide molecules are reported on various hydrophobic surfaces under scanning laser irradiation. A “dynamic exciton charge model” is developed to elucidate the underlying mechanism. The findings provide an innovative strategy for the design of microscale systems capable of continuous and directional movement driven by light.
Graphene processing using electron beam assisted metal deposition and masked chemical vapor deposition growth
Not Available
Fragment-Based Exploration of Binding Site Flexibility in Mycobacterium tuberculosis BioA
Abstract not provided
High-Performance Polymer Solar Cells Based on a Wide-Bandgap Polymer Containing Pyrrolo[3,4- f ]benzotriazole-5,7-dione with a Power Conversion Efficiency of 8.63%
A novel donor–acceptor type conjugated polymer based on a building block of 4,8-di(thien-2-yl)-6-octyl-2-octyl-5H-pyrrolo[3,4-f]benzotriazole-5,7(6H)-dione (TZBI) as the acceptor unit and 4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b']dithiophene as the donor unit, named as PTZBIBDT, is developed and used as an electron-donating material in bulk-heterojunction polymer solar cells. The resulting copolymer exhibits a wide bandgap of 1.81 eV along with relatively deep highest occupied molecular orbital energy level of -5.34 eV. Based on the optimized processing conditions, including thermal annealing, and the use of a water/alcohol cathode interlayer, the single-junction polymer solar cell based on PTZBIBDT:PC71BM ([6,6]-phenyl-C71-butyric acid methyl ester) blend film affords a power conversion efficiency of 8.63% with an open-circuit voltage of 0.87 V, a short circuit current of 13.50 mA cm -2 , and a fill factor of 73.95%, which is among the highest values reported for wide-bandgap polymers-based single-junction organic solar cells. The morphology studies on the PTZBIBDT:PC71BM blend film indicate that a fibrillar network can be formed and the extent of phase separation can be manipulated by thermal annealing. These results indicate that the TZBI unit is a very promising building block for the synthesis of wide-bandgap polymers for high-performance single-junction and tandem (or multijunction) organic solar cells.
High-Performance Non-Fullerene Organic Solar Cells Based on a Selenium-Containing Polymer Donor and a Twisted Perylene Bisimide Acceptor
A novel polymer donor (PBDTS-Se) is designed to match with a non-fullerene acceptor (SdiPBI-S). The corresponding solar cells show a high efficiency of 8.22%, which result from synergetic improvements of light harvesting, charge carrier transport and collection, and morphology. The results indicate that rational design of novel donor materials is important for non-fullerene organic solar cells.
Resonant soft X-ray scattering for polymer materials
Resonant Soft X-ray Scattering (RSoXS) was developed within the last few years, and the first dedicated resonant soft X-ray scattering beamline for soft materials was constructed at the Advanced Light Source, LBNL. RSoXS combines soft X-ray spectroscopy with X-ray scattering and thus offers statistical information for 3D chemical morphology over a large length scale range from nanometers to micrometers. Using RSoXS to characterize multi-length scale soft materials with heterogeneous chemical structures, we have demonstrated that soft X-ray scattering is a unique complementary technique to conventional hard X-ray and neutron scattering. Its unique chemical sensitivity, large accessible size scale, molecular bond orientation sensitivity with polarized X-rays, and high coherence have shown great potential for chemically specific structural characterization for many classes of materials.
Systematic Fluorination of P3HT: Synthesis of P(3HT- co -3H4FT)s by Direct Arylation Polymerization, Characterization, and Device Performance in OPVs
We present a strategy for tuning physical properties of P3HT-based copolymers by incorporating a fluorinated thiophene repeat unit. The synthesis and characterization of a series of fluorinated polythiophene P(3HT-co-3H4FT) materials are described, where the percentage of fluorinated repeat units in the polymer backbone is systematically varied from 0 to 100%. These P(3HT-co-3H4FT)s (P0, P25, P50, P75, and P100) were synthesized via direct arylation polymerization (DArP) methods. By varying the feed ratio of the two monomers, the percent of fluorinated repeat units (3H4FT) could be precisely controlled. As fluorination is increased, there is a strong effect on the electronic properties of the polymers, evidenced by a 0.4 eV drop in the E HOMO level for P100 when compared to P0. GIWAXS and TEM were used to determine the crystallinity and morphology. TEM analysis of thin film polymer/PCBM bulk-heterojunction blends indicates that increased fluorination does not result in stronger phase separation. As a result, organic photovoltaic devices were fabricated to evaluate changes in device performance as a result of fluorination.
Anisotropic parton escape is the dominant source of azimuthal anisotropy in transport models
Not Available
Alkylthio substituted thiophene modified benzodithiophene-based highly efficient photovoltaic small molecules
Explore the source record for details and available documents.