Engineering Papers⌕ Search

Engineering topics

Liu, Fangze

Publications and source records attributed to Liu, Fangze.

At least 37 records · Page 2

Halide Perovskite High- k Field Effect Transistors with Dynamically Reconfigurable Ambipolarity

Despite the remarkable optoelectronic properties of halide perovskites, achieving reproducible field effect transistor (FET) action in polycrystalline films at room temperature has been challenging and represents a fundamental bottleneck for understanding electronic charge transport in these materials. In this work, we report halide perovskite-based FET operation at room temperature with negligible hysteresis. Extensive measurements and device modeling reveal that incorporating high-k dielectrics enables modulation of the channel conductance. Furthermore, continuous bias cycling or resting allows dynamical reconfiguration of the FETs between p-type behavior and ambipolar FET with balanced electron and hole transport and an ON/OFF ratio up to 104 and negligible degradation in transport characteristics over 100 cycles. Furthermore, these results elucidate the path for achieving gate modulation in perovskite thin films and provide a platform to understand the interplay between the perovskite structure and external stimuli such as photons, fields, and functional substrates, which will lead to novel and emergent properties.

36 MATERIALS SCIENCE↗

Quantum Efficiency Enhancement of Bialkali Photocathodes by an Atomically Thin Layer on Substrates

Quantum efficiency (QE) enhancement in accelerator technology relevant to antimonide photocathodes (K 2 CsSb) is achieved by interfacing them with atomically thin 2D crystal layers. The enhancement occurs in a reflection mode, when a 2D crystal is placed in between the photocathodes and optically reflective substrates. Specifically, the peak QE at 405 nm (3.1 eV) increases by a relative 10%, whereas the long wavelength response at 633 nm (2.0 eV) increases by a relative 36% on average and up to 80% at localized “hot spot” regions when photocathodes are deposited onto graphene–coated stainless steel. There is a similar effect for photocathodes deposited on hexagonal boron nitride monolayer coatings using nickel substrates. The enhancement does not occur when reflective substrates are replaced with optically transparent sapphire. Optical transmission, X–ray diffraction (XRD), and X–ray fluorescence (XRF) revealed that thickness, crystal orientation, quality, and elemental stoichiometry of photocathodes do not appreciably change due to 2D crystal coatings. Furthermore these results suggest that optical interactions are responsible for the QE enhancements when 2D crystal sublayers are present on reflective substrates, and provide a pathway toward a simple method of QE enhancement in semiconductor photocathodes by an atomically thin 2D crystal on substrates.

43 PARTICLE ACCELERATORS↗

Perspectives on Designer Photocathodes for X-ray Free-Electron Lasers: Influencing Emission Properties with Heterostructures and Nanoengineered Electronic States

Here, the development of photoemission electron sources to specifically address the competing andnincreasingly stringent requirements of advanced light sources such as X-ray Free Electron Lasers (XFELs) motivates a comprehensive material-centric approach that integrates predictive compu- tational physics models, advanced nano-synthesis methods, and sophisticated surface science char- acterization with in situ correlated study of photoemission performance and properties. Related efforts in material science are adopting various forms of nanostructure (such as compositionally graded stoichiometry in heterostructured architectures, and quantum features) allowing for tailored electronic structure to control and enhance opto-electronic properties. These methods influence the mechanisms of photoemission (absorption, transport, and emission) but have not, as yet, been systematically considered for use in photocathode applications. Recent results and near-term op- portunities are described to exploit controlled functionality of nanomaterials for photoemission. An overview of the requirements and status is provided.

47 OTHER INSTRUMENTATION↗

Free-Standing Bialkali Photocathodes Using Atomically Thin Substrates

This study reports successful deposition of high quantum efficiency (QE) bialkali antimonide K2CsSb photocathodes on graphene films. The results pave the way for an ultimate goal of encapsulating technologically relevant photocathodes for accelerator technology with an atomically thin protecting layer to enhance lifetime while minimizing QE losses. A QE of 17% at approximate to 3.1 eV (405 nm) is the highest value reported so far on graphene substrates and is comparable to that obtained on stainless steel and nickel reference substrates. The spectral responses of the photocathodes on graphene exhibit signature features of K2CsSb including the characteristic absorption at approximate to 2.5 eV. Materials characterization based on X-ray fluorescence and X-ray diffraction reveals that the composition and crystal quality of these photocathodes deposited on graphene is comparable to those deposited on a reference substrate. Quantitative agreement between optical calculations and QE measurements for the K2CsSb on free suspended graphene and a graphene-coated metal substrate further confirms the high-quality interface between the photocathodes and graphene. Finally, a correlation between the QE and graphene quality as characterized by Raman spectroscopy suggests that a lower density of atomistic defects in the graphene films leads to higher QE of the deposited K2CsSb photocathodes.

accelerator technology↗

A photoemission moments model using density functional and transfer matrix methods applied to coating layers on surfaces: Theory

Recent experimental measurements of a bulk material covered with a small number of graphene layers reported by Yamaguchi et al. [NPJ 2D Mater. Appl. 1, 12 (2017)] (on bialkali) and Liu et al.[Appl. Phys. Lett. 110, 041607 (2017)] (on copper) and the needs of emission models in beam optics codes have lead to substantial changes in a Moments model of photoemission. The changes account for (i) a barrier profile and density of states factor based on density functional theory (DFT) evaluations, (ii) a Drude-Lorentz model of the optical constants and laser penetration depth, and (iii) a transmission probability evaluated by an Airy Transfer Matrix Approach. Importantly, the DFT results lead to a surface barrier profile of a shape similar to both resonant barriers and reflectionless wells: the associated quantum mechanical transmission probabilities are shown to be comparable to those recently required to enable the Moments (and Three Step) model to match experimental data but for reasons very different than the assumption by conventional wisdom that a barrier is responsible. The substantial modifications of the Moments model components, motivated by computational materials methods, are developed. The results prepare the Moments model for use in treating heterostructures and discrete energy level systems (e.g., quantum dots) proposed for decoupling the opposing metrics of performance that undermine the performance of advanced light sources like the x-ray Free Electron Laser. The consequences of the modified components on quan-tum yield, emittance, and emission models needed by beam optics codes are discussed. Published by AIP Publishing. https://doi.org/10.1063/1.5008600

36 MATERIALS SCIENCE↗

Understanding Film Formation Morphology and Orientation in High Member 2D Ruddlesden-Popper Perovskites for High-Efficiency Solar Cells

We report that 2D Ruddlesden–Popper (RP) perovskites have recently emerged as promising candidates for hybrid perovskite photovoltaic cells, realizing power-conversion efficiencies (PCEs) of over 10% with technologically relevant stability. To achieve solar cell performance comparable to the state-of-the-art 3D perovskite cells, it is highly desirable to increase the conductivity and lower the optical bandgap for enhanced near-IR region absorption by increasing the perovskite slab thickness. Here, the use of the 2D higher member (n = 5) RP perovskite (n-butyl-NH 3 ) 2 (MeNH 3 ) 4 Pb 5 I 16 in depositing highly oriented thin films from dimethylformamide/dimethylsulfoxide mixtures using the hot-casting method is reported. In addition, they exhibit superior environmental stability over thin films of their 3D counterpart. These films are assembled into high-efficiency solar cells with an open-circuit voltage of ≈1 V and PCE of up to 10%. This is achieved by fine-tuning the solvent ratio, crystal growth orientation, and grain size in the thin films. Finally, the enhanced performance of the optimized devices is ascribed to the growth of micrometer-sized grains as opposed to more typically obtained nanometer grain size and highly crystalline, densely packed microstructures with the majority of the inorganic slabs preferentially aligned out of plane to the substrate, as confirmed by X-ray diffraction and grazing-incidence wide-angle X-ray scattering mapping.

14 SOLAR ENERGY↗

Tunable and laser-reconfigurable 2D heterocrystals obtained by epitaxial stacking of crystallographically incommensurate Bi 2 Se 3 and MoS 2 atomic layers

Vertical stacking is widely viewed as a promising approach for designing advanced functionalities using two-dimensional (2D) materials. Combining crystallographically commensurate materials in these 2D stacks has been shown to result in rich new electronic structure, magnetotransport, and optical properties. In this context, vertical stacks of crystallographically incommensurate 2D materials with well-defined crystallographic order are a counterintuitive concept and, hence, fundamentally intriguing. We show that crystallographically dissimilar and incommensurate atomically thin MoS 2 and Bi 2 Se 3 layers can form rotationally aligned stacks with long-range crystallographic order. Our first-principles theoretical modeling predicts heterocrystal electronic band structures, which are quite distinct from those of the parent crystals, characterized with an indirect bandgap. Experiments reveal striking optical changes when Bi 2 Se 3 is stacked layer by layer on monolayer MoS 2 , including 100% photoluminescence (PL) suppression, tunable transmittance edge (1.1→0.75 eV), suppressed Raman, and wide-band evolution of spectral transmittance. Disrupting the interface using a focused laser results in a marked the reversal of PL, Raman, and transmittance, demonstrating for the first time that in situ manipulation of interfaces can enable “reconfigurable” 2D materials. We demonstrate submicrometer resolution, “laser-drawing” and “bit-writing,” and novel laser-induced broadband light emission in these heterocrystal sheets.

36 MATERIALS SCIENCE↗

Active bialkali photocathodes on free-standing graphene substrates

Here, the hexagonal structure of graphene gives rise to the property of gas impermeability, motivating its investigation for a new application: protection of semiconductor photocathodes in electron accelerators. These materials are extremely susceptible to degradation in efficiency through multiple mechanisms related to contamination from the local imperfect vacuum environment of the host photoinjector. Few-layer graphene has been predicted to permit a modified photoemission response of protected photocathode surfaces, and recent experiments of single-layer graphene on copper have begun to confirm these predictions for single crystal metallic photocathodes. Unlike metallic photoemitters, the integration of an ultra-thin graphene barrier film with conventional semiconductor photocathode growth processes is not straightforward. A first step toward addressing this challenge is the growth and characterization of technologically relevant, high quantum efficiency bialkali photocathodes on ultra-thin free-standing graphene substrates. Photocathode growth on free-standing graphene provides the opportunity to integrate these two materials and study their interaction. Specifically, spectral response features and photoemission stability of cathodes grown on graphene substrates are compared to those deposited on established substrates. In addition, we observed an increase of work function for the graphene encapsulated bialkali photocathode surfaces, which is predicted by our calculations. The results provide a unique demonstration of bialkali photocathodes on free-standing substrates, and indicate promise towards our goal of fabricating high-performance graphene encapsulated photocathodes with enhanced lifetime for accelerator applications.

36 MATERIALS SCIENCE↗

Vapor-Phase-Gating-Induced Ultrasensitive Ion Detection in Graphene and Single-Walled Carbon Nanotube Networks

Designing ultrasensitive detectors often requires complex architectures, high-voltage operations, and sophisticated low-noise measurements. Here, it is shown that simple low-bias two-terminal DC-conductance values of graphene and single-walled carbon nanotubes are extremely sensitive to ionized gas molecules. Incident ions form an electrode-free, dielectric- or electrolyte-free, bias-free vapor-phase top-gate that can efficiently modulate carrier densities up to ≈0.6 × 10 13 cm -2 . Surprisingly, the resulting current changes are several orders of magnitude larger than that expected from conventional electrostatic gating, suggesting the possible role of a current-gain inducing mechanism similar to those seen in photodetectors. These miniature detectors demonstrate charge–current amplification factor values exceeding 10 8 A C -1 in vacuum with undiminished responses in open air, and clearly distinguish between positive and negative ions sources. At extremely low rates of ion incidence, detector currents show stepwise changes with time, and calculations suggest that these stepwise changes can result from arrival of individual ions. Lastly, these sensitive ion detectors are used to demonstrate a proof-of-concept low-cost, amplifier-free, light-emitting-diode-based low-power ion-indicator.

36 MATERIALS SCIENCE↗

Single layer graphene protective gas barrier for copper photocathodes

Photocathodes can benefit from a thin protection layer and attain long-term stability. Graphene is potentially a good candidate for such application. In this paper, we report direct growth of single-layer graphene on single crystal Cu(110) photocathodes using chemical vapor deposition and the effective protection of copper photocathodes with graphene against degradation under atmospheric conditions. Due to the interaction and charge transfer between graphene and copper, the graphene-protected cathodes have 0.25 eV lower work function and 17% higher quantum efficiency at 250 nm compared with bare Cu cathodes. The graphene coating can protect copper photocathodes from degradation for more than 20 min in an exposure to 200 Torr of air. Finally, the validation of graphene-photocathode compatibility opens a new route to the lifetime-extension for photocathodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗