Engineering Papers⌕ Search

Engineering topics

Liu, Boyang

Publications and source records attributed to Liu, Boyang.

28 records · Page 2

Stabilizing the Garnet Solid-Electrolyte/Polysulfide Interface in Li–S Batteries

Chemical and physical short circuits are the main challenges faced by lithium batteries which compromise battery performance and safety. At the cathode, solvation of active cathode materials and shuttling of unwanted chemical species in the liquid electrolyte result in “chemical short circuits”, which deteriorate the Li metal electrode and limit the deployment of new cathode materials, such as high voltage cathodes, sulfur, and air/O 2 . In Li–S batteries, the repeated shuttling of polysulfides between electrodes constantly corrodes the Li metal anode and the loss of active material will result in low Coulombic efficiency. At the anode, Li dendrite penetration through the separator causes internal electronic, or “physical”, short circuits. Finally, several strategies have been reported to prevent chemical and physical short circuits by using a cathode host, small sulfur molecules, modified separators, or electrolyte additives to alleviate sulfur materials diffusion and shuttling, and finding ways to delay, confine, or block Li dendrites to extend the cycling lifetime and avoid thermal runaway in lithium metal batteries.

25 ENERGY STORAGE↗

Three-dimensional bilayer garnet solid electrolyte based high energy density lithium metal–sulfur batteries

To simultaneously address the challenges of chemical/physical short circuits and electrode volume variation, we demonstrate in this paper a three-dimensional (3D) bilayer garnet solid-state electrolyte framework for advanced Li metal batteries. The dense layer is reduced in thickness to a few microns and still retains good mechanical stability, thereby enabling the safe use of Li metal anodes. The thick porous layer acts as a mechanical support for the thin dense layer which serves as a host for high loading of cathode materials and provides pathways for continuous ion transport. Results show that the integrated sulfur cathode loading can reach >7 mg cm -2 while the proposed hybrid Li–S battery exhibits a high initial coulombic efficiency (>99.8%) and high average coulombic efficiency (>99%) during the subsequent cycles. Finally, this electrolyte framework represents a promising strategy to revolutionize Li-metal batteries by transitioning to all-solid-state batteries and can be extended to other cathode materials.

25 ENERGY STORAGE↗

Encapsulation of Metallic Na in an Electrically Conductive Host with Porous Channels as a Highly Stable Na Metal Anode

Room-temperature Na ion batteries (NIBs) have attracted great attention because of the widely available, abundant sodium resources and potentially low cost. Currently, the challenge of the NIB development is due primarily to the lack of a high-performance anode, while the Na metal anode holds great promise considering its highest specific capacity of 1165 mA h/g and lowest anodic potential. However, an uneven deposit, relatively infinite volume change, and dendritic growth upon plating/stripping cycles cause a low Coulombic efficiency, poor cycling performance, and severe safety concerns. In this study, a stable Na carbonized wood (Na–wood) composite anode was fabricated via a rapid melt infusion (about 5 s) into channels of carbonized wood by capillary action. The channels function as a high-surface-area, conductive, mechanically stable skeleton, which lowers the effective current density, ensures a uniform Na nucleation, and restricts the volume change over cycles. As a result, the Na–wood composite anode exhibited flat plating/stripping profiles with smaller overpotentials and stable cycling performance over 500 h at 1.0 mA/cm 2 in a common carbonate electrolyte system. Finally, in sharp comparison, the planar Na metal electrode showed a much shorter cycle life of 100 h under the same test conditions.

09 BIOMASS FUELS↗

Toward garnet electrolyte–based Li metal batteries: An ultrathin, highly effective, artificial solid-state electrolyte/metallic Li interface

Solid-state batteries are a promising option toward high energy and power densities due to the use of lithium (Li) metal as an anode. Among all solid electrolyte materials ranging from sulfides to oxides and oxynitrides, cubic garnet–type Li 7 La 3 Zr 2 O 12 (LLZO) ceramic electrolytes are superior candidates because of their high ionic conductivity (10 -3 to 10 -4 S/cm) and good stability against Li metal. However, garnet solid electrolytes generally have poor contact with Li metal, which causes high resistance and uneven current distribution at the interface. To address this challenge, we demonstrate a strategy to engineer the garnet solid electrolyte and the Li metal interface by forming an intermediary Li-metal alloy, which changes the wettability of the garnet surface (lithiophobic to lithiophilic) and reduces the interface resistance by more than an order of magnitude: 950 ohm·cm2 for the pristine garnet/Li and 75 ohm·cm 2 for the surface-engineered garnet/Li. Li 7 La 2.75 Ca 0.25 Zr 1.75 Nb 0.25 O 12 (LLCZN) was selected as the solid-state electrolyte (SSE) in this work because of its low sintering temperature, stabilized cubic garnet phase, and high ionic conductivity. This low area-specific resistance enables a solid-state garnet SSE/Li metal configuration and promotes the development of a hybrid electrolyte system. The hybrid system uses the improved solid-state garnet SSE Li metal anode and a thin liquid electrolyte cathode interfacial layer. This work provides new ways to address the garnet SSE wetting issue against Li and get more stable cell performances based on the hybrid electrolyte system for Li-ion, Li-sulfur, and Li-oxygen batteries toward the next generation of Li metal batteries.

25 ENERGY STORAGE↗

Negating interfacial impedance in garnet-based solid-state Li metal batteries

Garnet-type solid-state electrolytes have attracted extensive attention due to their high ionic conductivity, approaching 1 mS cm -1 , excellent environmental stability, and wide electrochemical stability window, from lithium metal to ~6 V. However, to date, there has been little success in the development of high-performance solid-state batteries using these exceptional materials, the major challenge being the high solid–solid interfacial impedance between the garnet electrolyte and electrode materials. In this paper, we effectively address the large interfacial impedance between a lithium metal anode and the garnet electrolyte using ultrathin aluminium oxide (Al 2 O 3 ) by atomic layer deposition. Li 7 La 2.75 Ca 0.25 Zr 1.75 Nb 0.25 O 12 (LLCZN) is the garnet composition of choice in this work due to its reduced sintering temperature and increased lithium ion conductivity. A significant decrease of interfacial impedance, from 1,710 Ω cm 2 to 1 Ω cm 2 , was observed at room temperature, effectively negating the lithium metal/garnet interfacial impedance. Experimental and computational results reveal that the oxide coating enables wetting of metallic lithium in contact with the garnet electrolyte surface and the lithiated-alumina interface allows effective lithium ion transport between the lithium metal anode and garnet electrolyte. Finally, we also demonstrate a working cell with a lithium metal anode, garnet electrolyte and a high-voltage cathode by applying the newly developed interface chemistry.

25 ENERGY STORAGE↗

Near-field nano-imager

An imaging device. In one embodiment, the imaging device includes a plurality of first electrode strips in parallel to each other along a first direction x, wherein each first electrode strip has an elongated body with a first surface and an opposite, second surface and a thickness n.sub.1. The imaging device also includes a plurality of second electrode strips in parallel to each other along a second direction y that is substantially perpendicular to the first direction x, wherein each second electrode strip has an elongated body with a first surface and an opposite, second surface and a thickness n.sub.2. The plurality of second electrode strips are positioned apart from the plurality of first electrode strips along a third direction z that is substantially perpendicular to the first direction x and the second direction y such that the plurality of first electrode strips and the plurality of second electrode strips are crossing each other accordingly to form a corresponding number of crossing points. And at each crossing point, a semiconductor component is filled between the second surface of a corresponding first electrode strip and the first surface of a corresponding second electrode strip to form an addressable pixel.

Liu, Boyang↗