Engineering Papers⌕ Search

Engineering topics

Litvin, F. L.

Publications and source records attributed to Litvin, F. L..

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Local synthesis and tooth contact analysis of face-milled spiral bevel gears

A new approach is proposed for the local synthesis of spiral bevel gears. The approach provides contact at the mean contact point with the desired deviation of the transmission error function by a predesigned parabolic function. The orientation of the contact path on the gear tooth surface and the length of the major axis of the instantaneous contact ellipse are also included in the analysis. A tooth contact analysis (TCA) computer program was developed to simulate meshing and contact of the gear tooth surfaces. A numerical example of the process is given.

Litvin, F. L.↗
NASA NTRS1989

New Methods For Generating Gear Surfaces

Report presents new methods for generating spur, helical, and spiral-bevel gears. Computer programs for analysis of tooth contacts developed for gears. Applied to spiral-bevel gears by use of currently available machinery and tools.

Coy, John J.↗
NASA NTRS1989

Tooth Contact Shift in Loaded Spiral Bevel Gears

An analytical method is presented to predict the shifts of the contact ellipses of spiral bevel gear teeth under load. The contact ellipse shift is the motion of the tooth contact position from the ideal pitch point to its location under load. The shifts are due to the elastic motions of the gear and pinion supporting shafts and bearings. The calculations include the elastic deflections of the gear shafts and the deflections of the four shaft bearings. The method assumes that the surface curvature of each tooth is constant near the unloaded pitch point. Results from these calculations will help designers reduce transmission weight without seriously reducing transmission performance.

Savage, M.↗
NASA NTRS1989

Topology of modified helical gears

The topology of several types of modified surfaces of helical gears is proposed. The modified surfaces allow absorption of a linear or almost linear function of transmission errors. These errors are caused by gear misalignment and an improvement of the contact of gear tooth surfaces. Principles and corresponding programs for computer aided simulation of meshing and contact of gears have been developed. The results of this investigation are illustrated with numerical examples.

Litvin, F. L.↗
NASA NTRS1989

Tooth contact shift in loaded spiral bevel gears

An analytical method is presented to predict the shifts of the contact ellipses of spiral bevel gear teeth under load. The contact ellipse shift is the motion of the tooth contact position from the ideal pitch point to its location under load. The shifts are due to the elastic motions of the gear and pinion supporting shafts and bearings. The calculations include the elastic deflections of the gear shafts and the deflections of the four shaft bearings. The method assumes that the surface curvature of each tooth is constant near the unloaded pitch point. Results from these calculations will help designers reduce transmission weight without seriously reducing transmission performance.

Savage, M.↗
NASA NTRS1989

Topology of modified helical gears

The topology of several types of modified surfaces of helical gears is proposed. The modified surfaces allow absorption of a linear or almost linear function of transmission errors. These errors are caused by gear misalignment and an improvement of the contact of gear tooth surfaces. Principles and corresponding programs for computer aided simulation of meshing and contact of gears have been developed. The results of this investigation are illustrated with numerical examples.

Litvin, F. L.↗
NASA NTRS1988

Generation of a crowned pinion tooth surface by a surface of revolution

A method of generating crowned pinion tooth surfaces using a surface of revolution is developed. The crowned pinion meshes with a regular involute gear and has a prescribed parabolic type of transmission errors when the gears operate in the aligned mode. When the gears are misaligned the transmission error remains parabolic with the maximum level still remaining very small (less than 0.34 arc sec for the numerical examples). Tooth contact analysis (TCA) is used to simulate the conditions of meshing, determine the transmission error, and determine the bearing contact.

Litvin, F. L.↗
NASA NTRS1988

Generation of a crowned pinion tooth surface by a plane

The topology of a crowned spur pinion tooth surface that reduces the level of transmission errors due to misalignment is described. The geometry of the modified pinion tooth surface and of the regular involute gear tooth surface is discussed. The tooth contact analysis between the meshing surfaces is also described. Generating a modified pinion tooth surface by a plane whose motion is controlled by a 5-degree-of-freedom system is investigated. The numerical results included indicate that the transmission error remains low as the gears are misaligned.

Litvin, F. L.↗
NASA NTRS1988

Crowned spur gears - Methods for generation and tooth contact analysis. I - Basic concepts, generation of the pinion tooth surface by a plane

A topology of crowned spur pinion tooth surface that reduces the level of transmission errors due to misalignment is proposed. The geometry of the deviated pinion tooth surface and regular gear tooth surface, along with tooth contact analysis is discussed. Generation of the deviated pinion tooth surface by a plane whose motion is controlled by a five-degree-of-freedom system is proposed. Numerical results are included and indicate that transmission errors remain low as the gears are misaligned.

Litvin, F. L.↗
NASA NTRS1988

Crowned spur gears - Methods for generation and Tooth Contact Analysis. II - Generation of the pinion tooth surface by a surface of revolution

A method for generation of crowned pinion tooth surfaces using a surface of revolution is developed. The crowned pinion meshes with a regular involute gear and has a prescribed parabolic type of transmission errors when the gears operate in the aligned mode. When the gears are misaligned the transmission error remains parabolic with the maximum level still remaining very small (less than 0.34 arc second for the numerical examples). Tooth Contact Analysis (TCA) is used to simulate the conditions of meshing, determine the transmission error, and the bearing contact.

Litvin, F. L.↗
NASA NTRS1988

Determination of settings of a tilted head-cutter for generation of hypoid and spiral bevel gears

Kinematics of Gleason mechanisms of hypoid and spiral bevel cutting machines are considered. These mechanisms are designated to install the position and tilt of the head cutter. The tilt of the head cutter with standard blades provides the required pressure angle. The authors have developed the matrix presentation of kinematics of these meachanisms and basic equations for the required settings. An example is presented based on the developed computation procedure.

Litvin, F. L.↗
NASA NTRS1987

Method for generation of spiral bevel gears with conjugate gear tooth surfaces

A method for generation of spiral bevel gears is proposed that provides conjugate gear tooth surfaces. This method is based on a new principle for the performance of parallel motion of a straight line that slides along two mating ellipses with related dimensions and parameters of orientation. The parallel motion of the straight line, that is, the contact normal, is performed parallel to the line which passes through the foci of symmetry of the related ellipses. The manufacturing of gears can be performed with the existing Gleason's equipment.

Litvin, F. L.↗
NASA NTRS1987

New generation methods for spur, helical, and spiral-bevel gears

New methods for generating spur, helical, and spiral-bevel gears are proposed. These methods provide the gears with conjugate gear tooth surfaces, localized bearing contact, and reduced sensitivity to gear misalignment. Computer programs have been developed for simulating gear meshing and bearing contact.

Litvin, F. L.↗
NASA NTRS1986

New generation methods for spur, helical, and spiral-bevel gears

New methods for generating spur, helical, and spiral-bevel gears are proposed. These methods provide the gears with conjugate gear tooth surfaces, localized bearing contact, and reduced sensitivity to gear misalignment. Computer programs have been developed for simulating gear meshing and bearing contact.

Litvin, F. L.↗
NASA NTRS1986

Synthesis and Optimization of Spiral Bevel Gears

Two mathematical models help in optimizing design of spiral bevel gears. In essence, replace actual generated tooth surface with mathematical conjugate approximation. Tooth surfaces of spiral bevel gears replaced (or approximated) by conjugate tooth surfaces. Surfaces generated by two conical surface's rigidly connected with each other and in linear tangency along common generatrix of tool cones and by conical surface and surface of revolution in linear tangency along circle. Gears have widespread applications in transmission systems of helicopters, airplanes, trucks, automobiles, tanks, and many other machines.

Litvin, F. L.↗
NASA NTRS1985

Generated spiral bevel gears - Optimal machine-tool settings and tooth contact analysis

Geometry and kinematic errors were studied for Gleason generated spiral bevel gears. A new method was devised for choosing optimal machine settings. These settings provide zero kinematic errors and an improved bearing contact. The kinematic errors are a major source of noise and vibration in spiral bevel gears. The improved bearing contact gives improved conditions for lubrication. A computer program for tooth contact analysis was developed, and thereby the new generation process was confirmed. The new process is governed by the requirement that during the generation process there is directional constancy of the common normal of the contacting surfaces for generator and generated surfaces of pinion and gear.

Litvin, F. L.↗
NASA NTRS1985

Study of meshing of beveled gears with normally decreasing arc teeth

The meshing of beveled gears was studied by the direct and inverse approaches. Gear wheels with teeth of equal height are studied, and wheels with normally-decreasing arc teeth. Different coordinate systems are utilized to plot the determination of the rotation of the originating gear wheel and the meshing line of the gear wheel which is cut. Matrices are used to determine the equations of the originating surfaces and the unit vectors of the normals to these originating surfaces.

Litvin, F. L.↗