Engineering topics
Litherland, Brandon L.
Publications and source records attributed to Litherland, Brandon L..
A Study on the Use of Solid-Oxide Fuel Cells for Increased Power Generation on Small Aircraft
A growing demand for higher-power electrical equipment on aircraft is driving the exploration of alternative electrical power generation devices. “Hybrid-electric” aircraft architectures that leverage multiple or alternative power sources are also becoming more popular with rising concerns over efficiency. Fuel cells are particularly interesting as auxiliary or secondary electrical power generation devices, due to their relative efficiency and longevity, and could be used as a “power pod” for vehicles without enough on-board electrical generation capability. This paper examines the feasibility and potential value of using an externally-mounted, hybridelectric, solid-oxide fuel cell (SOFC) power system on a Class IV unmanned aerial vehicle (UAV) for the purpose of power generation in excess of the baseline electrical load. Moreover, the paper will demonstrate that a SOFC auxiliary power unit (APU) provides significant value to an aircraft by producing a relatively large amount of additional electrical power for a relatively low initial investment when compared to producing additional power by scaling the engine.
A Performance Analysis of Folding Conformal Propeller Blade Designs
NASA’s X-57 Maxwell flight demonstrator has a high-lift system that includes 12 fixed- pitch high-lift propellers located upstream of the wing leading edge for lift augmentation at low speeds. These high-lift propellers are only required at low speeds, and to reduce drag, the propeller blades are folded conformally along the nacelles at other operating conditions. The method of designing the high-lift blades permits several variations of blade cross-section placement along the nacelle surface and a comparative performance analysis was needed to determine if any particular design showed significant benefits. We analyzed the performance of three conformal high-lift propeller designs and compared them to that of a non-conformal baseline propeller to establish both the benefit of stowable blades and the value of each variation. In this study, we first performed a drag analysis of each design in the stowed configuration at the X-57 cruise speed and altitude to determine the drag benefits of each conforming method. Then, among blade designs we compared the thrust, power, and lift for a given input shaft speed to establish any performance losses from the baseline. This analysis shows that the conformal blade designs do not have any appreciable performance losses compared to the baseline blades. Moreover, although the drag in the cruise condition is significantly less than for the non-folding baseline, the drag benefits of each conforming blade approach are similar and the value of each approach largely depends on the ease of integration into the nacelle. This paper presents the results of these studies and discusses the benefits and drawbacks of implementing the conformal blade designs. Specifically, we demonstrate that folding, conformal propeller blades contribute significantly less to cruise drag when compared to windmilling, with an increase relative to a. We also show a less than 1% difference in performance formal, folding propellers and the non-conforming baseline propeller.
Design and Performance of a Hybrid-Electric Fuel Cell Flight Demonstration Concept
As electric powertrain and propulsion-airframe integration technologies advance, airborne electric propulsion concepts appear to be on the cusp of disrupting or transforming aviation markets. One of the many challenges to this transformation lies within the onboard energy storage and generation technologies. State-of-the-art battery technology is heavy and lacks support infrastructure; purely combustion-based solutions to electrical power generation suffer from increased inefficiency as compared to a traditional combustion powertrain. This paper explores another alternative: a hybrid-electric, solid oxide fuel cell power system. This power system reforms traditional fuels to feed fuel cells that generate electrical power for the aircraft electric powertrain. A representative power system is designed based on the requirements for NASA’s X-57 Mod II electric flight demonstrator platform, and is shown to exceed system feasibility goals of 300 W/kg and 60% efficiency in at least one configuration. The hybrid-electric fuel cell power system is shown to be competitive with the range performance of a combustion-based power architecture and comparable in mission energy cost to a battery-electric power system.
A Method for Designing Conforming Folding Propellers
As the aviation vehicle design environment expands due to the in flux of new technologies, new methods of conceptual design and modeling are required in order to meet the customer's needs. In the case of distributed electric propulsion (DEP), the use of high-lift propellers upstream of the wing leading edge augments lift at low speeds enabling smaller wings with sufficient takeoff and landing performance. During cruise, however, these devices would normally contribute significant drag if left in a fixed or windmilling arrangement. Therefore, a design that stows the propeller blades is desirable. In this paper, we present a method for designing folding-blade configurations that conform to the nacelle surface when stowed. These folded designs maintain performance nearly identical to their straight, non-folding blade counterparts.
Comparison of Aero-Propulsive Performance Predictions for Distributed Propulsion Configurations
NASA's X-57 "Maxwell" flight demonstrator incorporates distributed electric propulsion technologies in a design that will achieve a significant reduction in energy used in cruise flight. A substantial portion of these energy savings come from beneficial aerodynamic-propulsion interaction. Previous research has shown the benefits of particular instantiations of distributed propulsion, such as the use of wingtip-mounted cruise propellers and leading edge high-lift propellers. However, these benefits have not been reduced to a generalized design or analysis approach suitable for large-scale design exploration. This paper discusses the rapid, "design-order" toolchains developed to investigate the large, complex tradespace of candidate geometries for the X-57. Due to the lack of an appropriate, rigorous set of validation data, the results of these tools were compared to three different computational flow solvers for selected wing and propulsion geometries. The comparisons were conducted using a common input geometry, but otherwise different input grids and, when appropriate, different flow assumptions to bound the comparisons. The results of these studies showed that the X-57 distributed propulsion wing should be able to meet the as-designed performance in cruise flight, while also meeting or exceeding targets for high-lift generation in low-speed flight.
Overcoming the Adoption Barrier to Electric Flight
Electrically-powered aircraft can enable dramatic increases in efficiency and reliability, reduced emissions, and reduced noise as compared to today's combustion-powered aircraft. This paper describes a novel flight demonstration concept that will enable the benefits of electric propulsion, while keeping the extraordinary convenience and utility of common fuels available at today's airports. A critical gap in airborne electric propulsion research is addressed by accommodating adoption at the integrated aircraft-airport systems level, using a confluence of innovative but proven concepts and technologies in power generation and electricity storage that need to reside only on the airframe. Technical discriminators of this demonstrator concept include (1) a novel, high-efficiency power system that utilizes advanced solid oxide fuel cells originally developed for ultra-long-endurance aircraft, coupled with (2) a high-efficiency, high-power electric propulsion system selected from mature products to reduce technical risk, assembled into (3) a modern, high-performance demonstration platform to provide useful and compelling data, both for the targeted early adopters and the eventual commercial market.