Engineering topics

Lisagor, W. Barry

Publications and source records attributed to Lisagor, W. Barry.

8 records

NASA NTRS2007

Development and Processing Improvement of Aerospace Aluminum Alloys

This final report, in multiple presentation format, describes a comprehensive multi-tasked contract study to improve the overall property response of selected aerospace alloys, explore further a newly-developed and registered alloy, and correlate the processing, metallurgical structure, and subsequent properties achieved with particular emphasis on the crystallographic orientation texture developed. Modifications to plate processing, specifically hot rolling practices, were evaluated for Al-Li alloys 2195 and 2297, for the recently registered Al-Cu-Ag alloy, 2139, and for the Al-Zn-Mg-Cu alloy, 7050. For all of the alloys evaluated, the processing modifications resulted in significant improvements in mechanical properties. Analyses also resulted in an enhanced understanding of the correlation of processing, crystallographic texture, and mechanical properties.

Lisagor, W. Barry↗

NASA NTRS2007

Development and Processing Improvement of Aerospace Aluminum Alloys-Development of AL-Cu-Mg-Ag Alloy (2139)

This final report supplement in presentation format describes a comprehensive multi-tasked contract study to continue the development of the silver bearing alloy now registered as aluminum alloy 2139 by the Aluminum Association. Two commercial scale ingots were processed into nominal plate gauges of two, four and six inches, and were extensively characterized in terms of metallurgical and crystallographic structure, and resulting mechanical properties. This report includes comparisons of the property combinations for this alloy and 2XXX and 7XXX alloys more widely used in high performance applications. Alloy 2139 shows dramatic improvement in all combinations of properties, moreover, the properties of this alloy are retained in all gauge thicknesses, contrary to typical reductions observed in thicker gauges of the other alloys in the comparison. The advancements achieved in this study are expected to result in rapid, widespread use of this alloy in a broad range of ground based, aircraft, and spacecraft applications.

Cho, Alex↗

NASA NTRS1998

Creep Strain and Strain Rate Response of 2219 Al Alloy at High Stress Levels

As a result of high localized plastic deformation experienced during proof testing in an International Space Station connecting module, a study was undertaken to determine the deformation response of a 2219-T851 roll forging. After prestraining 2219-T851 Al specimens to simulate strains observed during the proof testing, creep tests were conducted in the temperature range from ambient temperature to 107 C (225 F) at stress levels approaching the ultimate tensile strength of 2219-T851 Al. Strain-time histories and strain rate responses were examined. The strain rate response was extremely high initially, but decayed rapidly, spanning as much as five orders of magnitude during primary creep. Select specimens were subjected to incremental step loading and exhibited initial creep rates of similar magnitude for each load step. Although the creep rates decreased quickly at all loads, the creep rates dropped faster and reached lower strain rate levels for lower applied loads. The initial creep rate and creep rate decay associated with primary creep were similar for specimens with and without prestrain; however, prestraining (strain hardening) the specimens, as in the aforementioned proof test, resulted in significantly longer creep life.

Taminger, Karen M. B.↗

NASA NTRS1993

Vehicle systems

Perspectives of the subpanel on expendable launch vehicle structures and cryotanks are: (1) new materials which provide the primary weight savings effect on vehicle mass/size; (2) today's investment; (3) typically 10-20 years to mature and fully characterize new materials.

Bales, Tom↗

NASA NTRS1993

Vehicle Systems Panel deliberations

The Vehicle Systems Panel addressed materials and structures technology issues related to launch and space vehicle systems not directly associated with the propulsion or entry systems. The Vehicle Systems Panel was comprised of two subpanels - Expendable Launch Vehicles & Cryotanks (ELVC) and Reusable Vehicles (RV). Tom Bales, LaRC, and Tom Modlin, JSC, chaired the expendable and reusable vehicles subpanels, respectively, and co-chaired the Vehicle Systems Panel. The following four papers are discussed in this section: (1) Net Section components for Weldalite Cryogenic Tanks, by Don Bolstad; (2) Build-up Structures for Cryogenic Tanks and Dry Bay Structural Applications, by Barry Lisagor; (3) Composite Materials Program, by Robert Van Siclen; (4) Shuttle Technology (and M&S Lessons Learned), by Stan Greenberg.

Bales, Tom↗

NASA NTRS1993

Built-up Al-Li structures for cryogenic tank and dry bay applications

The objectives are: (1) to demonstrate the cost benefits of built-up cryotank and dry bay structures; (2) to study of benefits of using Al alloys; (3) to study of benefit of using Al-Li alloys; (4) to evaluate alternative low-cost stiffener and joining concepts.

Lisagor, W. Barry↗

NASA NTRS1990

Advanced metallics for high temperature airframe structures

The development of new lower density materials with improved properties and higher use temperatures is considered essential enabling technology for nearly all envisioned aeronautics structural applications on the horizon. Notable examples of such applications include the High Speed Civil Transport (HSCT) in the supersonic regime and the National Aerospace Plane (NASP) in the hypersonic regime. This paper reviews the vehicle as well as material requirements for such applications and identifies candidate emerging metallics along with examples of reported properties. Finally, critical needs and current development status of candidate metallics are addressed.

Lisagor, W. Barry↗

NASA NTRS1988

Materials and structures for hypersonic vehicles

Hypersonic vehicles are envisioned to require, in addition to carbon-carbon and ceramic-matrix composities for leading edges heated to above 2000 F, such 600 to 1800 F operating temperature materials as advanced Ti alloys, nickel aluminides, and metal-matrix composited; These possess the necessary low density and high strength and stiffness. The primary design drivers are maximum vehicle heating rate, total heat load, flight envelope, propulsion system type, mission life requirements and liquid hydrogen containment systems. Attention is presently given to aspects of these materials and structures requiring more intensive development.

Tenney, Darrel R.↗