Engineering Papers⌕ Search

Engineering topics

Lin, Yi

Publications and source records attributed to Lin, Yi.

At least 19 records

Ultrafast creation of a light-induced semimetallic state in strongly excited 1T-TiSe 2

Screening, a ubiquitous phenomenon associated with the shielding of electric fields by surrounding charges, has been widely adopted as a means to modify a material’s properties. While most studies have relied on static changes of screening through doping or gating thus far, here we demonstrate that screening can also drive the onset of distinct quantum states on the ultrafast timescale. By using time- and angle-resolved photoemission spectroscopy, we show that intense optical excitation can drive 1T-TiSe 2 , a prototypical charge density wave material, almost instantly from a gapped into a semimetallic state. By systematically comparing changes in band structure over time and excitation strength with theoretical calculations, we find that the appearance of this state is likely caused by a dramatic reduction of the screening length. In summary, this work showcases how optical excitation enables the screening-driven design of a nonequilibrium semimetallic phase in TiSe 2 , possibly providing a general pathway into highly screened phases in other strongly correlated materials.

36 MATERIALS SCIENCE↗

Progressive evolutions of non-fused ring electron acceptors toward efficient organic solar cells with improved photocurrent and reduced energy loss

Resolving competitive counterbalance between high external quantum efficiency (EQE) response and low energy loss is critical for achieving efficient organic solar cells (OSCs), including those based on low-cost non-fused-ring electron acceptor (NFREA). In this work, we performed a comparable study by utilizing four NFREAs with progressive evolutions in molecular structures, energetic levels, spectral coverages, crystallinity, etc, to pair with polymer donor J52. By regulating the terminal and side chains of NFREAs, the enhanced intramolecular charge transfer (ICT) effect allows O-PC-EH possessing the broader spectral coverage for higher photocurrent, the reduced energetic offset enables O-PC-EH-based device owning higher luminescence property for lower energy loss, the strengthened crystallinity endows O-PC-EH-based blend better charge transport property for less charge recombination. With those comprehensive managements from molecule to blend properties, the J52:O-PC-EH-based OSCs achieved the best efficiency of 14.4% (certified: 14.1%) with benefits in all the three device parameters. Here, this work reveals the importance of fine-tuning molecular structures of NFREAs according to paired polymer donor for maximizing the device performances.

14 SOLAR ENERGY↗

Evidence for a delocalization quantum phase transition without symmetry breaking in CeCoIn 5

The study of quantum phase transitions that are not clearly associated with broken symmetry is a major effort in condensed matter physics, particularly in regard to the problem of high-temperature superconductivity, for which such transitions are thought to underlie the mechanism of superconductivity itself. Here we argue that the putative quantum critical point in the prototypical unconventional superconductor CeCoIn 5 is characterized by the delocalization of electrons in a transition that connects two Fermi surfaces of different volumes, with no apparent broken symmetry. Drawing on established theory of f-electron metals, we discuss an interpretation for such a transition that involves the fractionalization of spin and charge, a model that effectively describes the anomalous transport behavior we measured for the Hall effect.

36 MATERIALS SCIENCE↗

Ion‐Conducting, Electron‐Blocking Layer for High‐Performance Solid Electrolytes

Lithium metal batteries bring greater promise for energy density, often relying on solid‐state electrolytes to meet critical benchmarks. However, Li dendrite formation is a prevailing problem that limits the cycle life and Coulombic efficiency of solid‐state Li metal batteries. For the first time, a thin (<100 nm) layer of electronically insulating, ionically conducting lithium phosphorus oxynitride (LiPON) is applied using atomic layer deposition between a Li anode and garnet Li 7 La 3 Zr 2 O 12 (LLZO). The performance of a conformal LiPON layer as an electron barrier in symmetric Li‐LLZO cells is observed through potential step chronoamperometry, galvanostatic cycling, electron microscopy, and various spectroscopic techniques. The LiPON‐coated LLZO achieves 100 times lower electronic conductance than LLZO alone. Cycling carried out at 0.1 mA cm −2 for 100 cycles demonstrates that suppression of electron pathways into the bulk solid electrolyte improves the cycle life of a lithium metal cell. These findings suggest an electronic conductivity effect in solid‐state electrolytes. A strategy is demonstrated to design thin‐film (LiPON)‐modulated bulk solid‐state electrolytes (LLZO) capable of maintaining high ionic conductivity and electrochemical stability while reducing the effective electronic conductivity, which results in significantly decreased dendrite formation, improved cycle life, and greater interfacial integrity between the electrolyte and a Li anode.

Hitz, Emily M.↗

Dry-pressed lithium nickel cobalt manganese oxide (NCM) cathodes enabled by holey graphene host

There is an increasing demand for electric vehicle batteries with higher energy densities that can be manufactured with low cost utilizing environmentally friendly processes. Lithium nickel cobalt manganese oxides (NCM), such as LiNi(0.5)Co(0.2)Mr(0.3)O(2) (NCM523), are commonly used in commercial lithium ion batteries for electric vehicle applications. These cathodes are typically fabricated using environmentally hazardous, energy intensive, and time-consuming solvent-based slurry casting processes. Polymeric binders, also required for cathode preparation, add weight and can undergo parasitic reactions during battery cycling. Here we report a facile, solvent-free, binder-free, and rapid cold-press electrode fabrication process to prepare high mass loading NCM cathodes within minutes. This process is enabled by the use of holey graphene, a unique lightweight, compressible carbon nanomaterial that serves as both a binder and an electrically conductive matrix. NCM cathodes fabricated by this method are stable and exhibit good active material utilization. A significant advantage for the dry-press process is that the electrode mass loadings can be readily increased simply by adding more composite powder to the compression molding die, resulting in improved areal capacities that are attractive for applications requiring high energy per unit footprint. (C) 2020 Elsevier Ltd. All rights reserved.

25 ENERGY STORAGE↗

High-Performance, Long-Life, Rechargeable Li–CO 2 Batteries based on a 3D Holey Graphene Cathode Implanted with Single Iron Atoms

A highly efficient cathode catalyst for rechargeable Li-CO 2 batteries is successfully synthesized by implanting single iron atoms into 3D porous carbon architectures, consisting of interconnected N,S-codoped holey graphene (HG) sheets. The unique porous 3D hierarchical architecture of the catalyst with a large surface area and sufficient space within the interconnected HG framework can not only facilitate electron transport and CO 2 /Li+ diffusion, but also allow for a high uptake of Li 2 CO 3 to ensure a high capacity. Consequently, the resultant rechargeable Li-CO 2 batteries exhibit a low potential gap of approximate to 1.17 V at 100 mA g -1 and can be repeatedly charged and discharged for over 200 cycles with a cut-off capacity of 1000 mAh g -1 at a high current density of 1 A g -1 . Density functional theory calculations are performed and the observed appealing catalytic performance is correlated with the hierarchical structure of the carbon catalyst. This work provides an effective approach to the development of highly efficient cathode catalysts for metal-CO 2 batteries and beyond.

(2) batteries↗

Reliable Bonding of Composite Laminates Using Reflowable Epoxy Resins

Epoxy matrix composites assembled with adhesives maximize the performance of aerospace structures, but the possibility of forming weak bonds requires the installation of redundant fasteners, which add weight and manufacturing cost. Co-cured joints (e.g. unitized composite structures) are immune to weak bonds because the uncured resin undergoes diffusion and mixing through the joint. A means of co-curing complex structures may reduce the need for redundant fasteners in bondlines. To this end, NASA started the AERoBOND project to develop novel joining materials to enable a “secondary-co-cure” assembly process. Aerospace epoxy resin systems reformulated with offset stoichiometry prevented the resin from advancing beyond the gel point during a conventional autoclave cure cycle up to 180 °C. The offset resins were applied to the joining surfaces of laminate preforms as prepreg. Two surfaces with complimentary offset resins were joined using conventional secondary bonding techniques. Preliminary efforts have indicated that the resulting joint has no discernable interface and appears as a conventional co-cured laminate under optical magnification. This report will discuss the initial work performed regarding formulation of the epoxy resin system using calorimetry, rheology, and mechanical testing.

Palmieri, Frank L.↗

Reinforcing Additives for Ice Adhesion Reduction Coatings

Adhesion of contaminants has been identified as a ubiquitous issue for aeronautic exterior surfaces. In-flight icing is particularly hazardous for all aircraft and can be experienced throughout the year under the appropriate environmental conditions. On larger vehicles, the accretion of ice could result in loss of lift, engine failure, and potentially loss of vehicle and life were it not for active deicing or anti-icing equipment. Smaller vehicles though cannot support the mass and mechanical complexity of active ice mitigating systems and thus must rely upon passive approaches or avoid icing conditions altogether. One approach that may be applicable to all aircraft is the use of coatings. Durability remains an issue and has prevented realization of coatings for leading edge contamination mitigation. In this work, epoxy coatings were generated as a passive approach for ice adhesion mitigation and methods to improve durability were evaluated. Highly cross-linked epoxy systems can be extremely rigid, which could have deleterious consequences regarding application as a leading edge coating. Incorporation of flexible species, such as poly(ethylene glycol) may improve coating toughness.8 Additionally, core-shell rubber (CSR) particles have been utilized to improve fracture toughness of epoxies.9 Both of these more established additives are investigated in this work. An emerging additive that is also evaluated here is holey graphene. This nanomaterial possesses many of the advantageous properties of graphene (excellent mechanical properties, thermal and electrical conductivity, large surface area, etc.) while also exhibiting behaviors associated with flexible, porous materials (i.e., compressibility, increased permeation, etc.). Holey graphene, HG, was synthesized by the oxidation of defect-rich sites on graphene sheets through controlled thermal expo-sure.10 It is envisioned that the porous nature of HG would allow resin penetration through the graphitic plane, resulting in better interfacial interaction and therefore better translation of the nanomaterial’s properties to the surrounding matrix.

Wohl, Christopher J↗

Phase transition and electronic structure evolution of MoTe 2 induced by W substitution

We report that the transition-metal dichalcogenide compounds MoTe 2 and WTe 2 are polymorphic with both semiconducting and metallic phases. The thermodynamically stable phase of WTe 2 at room temperature is orthorhombic and metallic and displays a wide range of interesting phenomena including type-II Weyl fermions, titanic magnetoresistance and superconductivity in bulk, and quantum spin Hall insulator behavior in the monolayer case. On the other hand, the stable phase of MoTe 2 at room temperature is a trigonal prismatic semiconductor that has a direct gap in the monolayer with strong spin-orbit coupling. The alloy series Mo 1-x W x Te 2 thus offers the possibility for tuning the structural and, consequently, electronic phases via tuning of the composition. Here, we report comprehensive studies of the electronic structure of Mo 1-x W x Te 2 alloys using angle-resolved photoemission spectroscopy and first-principles calculations as a function of composition. At room temperature, we find a sharp boundary between the orthorhombic and the trigonal prismatic phases at x = 0.10 using structural characterization. Finally, we also show that by compositional tuning it is possible to control the band inversion in this series of compounds thus yielding important consequences for topological surface states.

36 MATERIALS SCIENCE↗

Tankyrase regulates apoptosis by activating JNK signaling in Drosophila

Highlights: • Ectopic expression of DTNKS induces wing and eye defects. • DTNKS positively regulates cell apoptosis. • DTNKS regulates apoptosis by controlling JNK signaling activity. Programmed cell death (PCD), or apoptosis, plays essential roles in various cellular and developmental processes, and dysregulation of apoptosis causes many diseases. Thus, regulation of apoptotic process is very important. Drosophila tankyrase (DTNKS) is an evolutionarily conserved protein with poly(ADP-ribose) polymerase activity. In mammalian cells, tankyrases (TNKSs) have been reported to regulate cell death. To determine whether DTNKS plays function in inducing apoptosis in in vivo development, we used Drosophila as a model system and generated transgenic flies expressing DTNKS. We show that ectopic expression of DTNKS promotes caspase-dependent apoptosis and knockdown of DTNKS by RNAi dramatically alleviates apoptotic defect caused by ectopic expression of pro-apoptotic protein hid or rpr in the adult eye. Moreover, our result shows that ectopic expression of DTNKS triggers the activation of c-Jun N-terminal kinase (JNK) signaling, which is required for DTNKS-mediated apoptosis. Taken together, our finding identifies the role of DTNKS in regulating apoptosis by activating JNK signaling in Drosophila.

60 APPLIED LIFE SCIENCES↗

Effect of aging treatment on microstructures, tensile properties and intergranular corrosion behavior of Al–Cu–Li alloy

Highlights: • T8 duplex aging greatly promoted the precipitation of strengthening phases. • Heavy precipitation of strengthening phases led to enhancing of tensile properties. • Intergranular corrosion sensibility can be reduced by T8 duplex aging greatly. - Abstract: The influence of aging treatment on microstructures, tensile properties and corrosion properties of Al–Cu–Li alloy was investigated. The results show that the T8 duplex aging treatment was more effective than T6 and T8 single aging treatment in enhancing the tensile properties and improving the intergranular corrosion (IGC) resistance. Based on the microstructure observation, tensile test, electrochemical experiment and IGC measurement, the factors which affect the microstructures, tensile properties and IGC behavior changing of Al–Cu–Li alloy during aging treatments were discussed in detail.

36 MATERIALS SCIENCE↗

Optimization of Picosecond Laser Parameters for Surface Treatment of Composites Using a Design of Experiments (DOE) Approach

Based on guidelines from the Federal Aviation Administration, research supported by the NASA Advanced Composites Project is investigating methods to improve process control for surface preparation and pre-bond surface characterization on aerospace composite structures. The overall goal is to identify high fidelity, rapid, and reproducible surface treatments and surface characterization methods to reduce the uncertainty associated with the bonding process. The desired outcome is a more reliable bonded airframe structure, and to reduce time to achieve certification. In this work, a design of experiments (DoE) approach was conducted to determine optimum laser ablation conditions using a pulsed laser source with a nominal pulse width of 10 picoseconds. The laser power, frequency, scan speed, and number of passes (1 or 2) were varied within the laser system operating boundaries. Aerospace structural carbon fiber reinforced composites (Torayca® 3900-2/T800H) were laser treated, then characterized for contamination, and finally bonded for mechanical testing. Pre-bond characterization included water contact angle (WCA) using a handheld device, ablation depth measurement using scanning electron microscopy (SEM), and silicone contamination measurement using laser induced breakdown spectroscopy (LIBS). In order to accommodate the large number of specimens in the DoE, a rapid-screening, double cantilever beam (DCB) test specimen configuration was devised based on modifications to ASTM D5528. Specimens were tested to assess the failure modes observed under the various laser surface treatment parameters. The models obtained from this DoE indicated that results were most sensitive to variation in the average laser power. Excellent bond performance was observed with nearly 100% cohesive failure for a wide range of laser parameters. Below about 200 mW, adhesive failure was observed because contamination was left on the surface. For laser powers greater than about 600 mW, large amounts of fiber were exposed, and the failure mode was predominately fiber tear.

Palmieri, Frank L.↗

Determination of Trace Silicone Contamination on Composites by Quantitative XPS and LIBS

Surface treatment and surface characterization techniques are critical to ensure that adherends are chemically activated and free of contaminants prior to adhesive bonding. Silicone contamination from mold-release agents and other sources can interfere with interfacial bonding, decreasing the durability and performance of bonded composite structures. Tools and methods are needed that can be used in a production environment to reliably detect low levels of contaminants in a rapid, simple, and cost-effective manner to improve bond reliability. In this work, surface characterization of carbon fiber reinforced polymer (CFRP) composites was performed using laser induced breakdown spectroscopy (LIBS) and the results were compared with those obtained from X-ray photoelectron spectroscopy (XPS). The objective was to investigate the ability to quantify the surface species measured by LIBS since it offers many advantages over XPS in terms of ease of use, sample preparation, and real-time results. The as-processed CFRP panels had trace surface silicone contamination from the fabrication process, the source of which was not investigated. The composites were laser treated at select average laser power levels, resulting in varying levels of contamination reduction. The Si atomic percentage measurements using XPS were conducted both before and after laser ablation. The XPS results were compared with those obtained from LIBS to assess the reliability of each technique for surface contaminant characterization. The results showed an excellent correlation in Si atomic concentration between the two techniques.

Ledesma, Rodolfo↗

Excitation and characterization of image potential state electrons on quasi-free-standing graphene

We investigate the band structure of image potential states in quasi-free-standing graphene (QFG) monolayer islands using angle-resolved two-photon-photoemission spectroscopy. Direct probing by low-energy electron diffraction shows that QFG is formed following oxygen intercalation into the graphene-Ir(111) interface. Despite the apparent decoupling of the monolayer graphene from the Ir substrate, we find that the binding energy of the n = 1 image potential state on these QFG islands increases by 0.17 eV, as compared to the original Gr/Ir(111) interface. We use calculations based on density-functional theory to construct an empirical, one-dimensional potential that quantitatively reproduces the image potential state binding energy and links the changes in the interface structure to the shift in energy. Specifically, two factors contribute comparably to this energy shift: a deeper potential well arising from the presence of intercalated oxygen adatoms and a wider potential well associated with the increase in the graphene-Ir distance. While image potential states have not been observed previously on QFG by photoemission, our paper now demonstrates that they may be strongly excited in a well-defined QFG system produced by oxygen intercalation. Finally, this opens an opportunity for studying the surface electron dynamics in QFG systems, beyond those found in typical nonintercalated graphene-on-substrate systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Picosecond Pulsed Laser Ablation for the Surface Preparation of Epoxy Composites

As part of a technical challenge under the Advanced Composites Program, methods for improving pre-bond process control for aerospace composite surface treatments and inspections, in conjunction with Federal Aviation Administration guidelines, are under investigation. The overall goal is to demonstrate high fidelity, rapid and reproducible surface treatment and surface characterization methods to reduce uncertainty associated with the bonding process. The desired outcomes are reliable bonded airframe structure, and reduced timeline to certification. In this work, laser ablation was conducted using a q-switched Nd:YVO4 laser capable of nominal pulse durations of 8 picoseconds (ps). Aerospace structural carbon fiber reinforced composites with an epoxy resin matrix were laser treated, characterized, processed into bonded assemblies and mechanically tested. The characterization of ablated surfaces were conducted using scanning electron microscopy (SEM), water contact angle (WCA) goniometry, micro laser induced breakdown spectroscopy (uLIBS), and electron spin resonance (ESR). The bond performance was assessed using a double cantilever beam (DCB) test with an epoxy adhesive. The surface characteristics and bond performance obtained from picosecond ablated carbon fiber reinforced plastics (CFRPs) are presented herein.

Palmieri, Frank↗