Engineering Papers⌕ Search

Engineering topics

Lillo, Thomas

Publications and source records attributed to Lillo, Thomas.

DEVELOPMENT OF A SCALABLE THERMOMECHANICAL PROCESS (TMP) FOR THICK BAINITIC ARMOR STEEL

A bainite phase-based alloy and associated thermomechanical process were developed to produce (2.5 to over 5 cm) thick armor-grade steel with uniform through-thickness high hardness and strength. The alloy composition and the final-critical (austenite to bainite) isothermal transformation step were specifically designed to utilize a simple and versatile air-cool/quench method to keep a low upfront capital cost and to provide the ability to continuously control the cooling rate in real time, in order to produce maximum volume fraction of bainite phase, and promote uniformly distributed strength and hardness. Final thickness of 2.5 cm and 5.7 cm steel plates were fabricated for characterization, testing and evaluation and found to possess uniform through-thickness hardness between 53 to 55 HRC and dynamic compressive strength of up to 2 GPa.

36 MATERIALS SCIENCE↗

Quarterly Management Document – FY17, 4th Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

During the 4th quarter of FY17 modeling and simulation development of creep in nickel-based alloys was continued with a focus on incorporation of simulated alloy microstructures into the creep model. Additionally, the model was calibrated with experimental creep data from Alloy 617. Experimental data collection also continued with creep tests, stress drop tests and characterization of alloy microstructures.

36 MATERIALS SCIENCE↗

Quarterly Management Document – FY17, 3rd Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

Progress on modeling the the creep of thick sections welds in Alloy 740H is reported. Climb of dislocations during creep has been added to the model. Creep testing is continuing and stress drop testing has been initiated to determine the threshold stress of this particle-strengthened alloy. Work has also begun on generating synthetic microstructures, representative of experimental microstructures, from data collected with EBSD. This will enable incorporation of experimental microstructures into the modeling and simulation effort.

36 MATERIALS SCIENCE↗

Thermal Conductivity in Nanocrystalline Ceria Thin Films

The thermal conductivity of nanocrystalline ceria films grown by unbalanced magnetron sputtering is determined as a function of temperature using laser-based modulated thermoreflectance. The films exhibit significantly reduced conductivity compared with stoichiometric bulk CeO2. A variety of microstructure imaging techniques including X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron analysis, and electron energy loss spectroscopy indicate that the thermal conductivity is influenced by grain boundaries, dislocations, and oxygen vacancies. The temperature dependence of the thermal conductivity is analyzed using an analytical solution of the Boltzmann transport equation. The conclusion of this study is that oxygen vacancies pose a smaller impediment to thermal transport when they segregate along grain boundaries.

99 GENERAL AND MISCELLANEOUS↗

Aging of Alloy 617 at 650 and 750°C

Alloy 617 has been selected as the primary candidate for heat exchanger applications in advanced reactors. For the VHTR this application could require extended service up to a reactor outlet temperature of 950°C. A key hurdle to using this alloy in the VHTR heat exchanger application is qualifying the alloy for Section III of the ASME Boiler and Pressure Vessel Code. In order to Code qualify the material it is necessary to characterize the influence of long term aging on the mechanical behavior. Alloy 617 has been aged at 650 and 750°C for times up to 5300 hours. The microstructure after aging has been characterized using optical and transmission electron microscopies. It has been determined that in addition to carbides, a significant volume fraction of γ’ phase (Ni 3 Al) is formed at these temperatures. The γ’ does not contribute significantly to changing the tensile or impact properties of the aged material. It does, however, appear to increase creep resistance and impede creep crack growth.

36 MATERIALS SCIENCE↗

Chromium-free nickel alloys for hot sulfuric and sulfur environments

There are few adequate materials available for severe corrosion conditions, like those of the S–I thermochemical cycle. High Si, Ni-alloys have excellent corrosion resistance, especially in mineral acids, but have typically been limited by poor mechanical properties or difficult fabrication issues. The ductility of nickel silicide, Ni3Si, can be improved through a combination of micro- and macro-alloying. Nb and other minor alloying elements yield a cast alloy with excellent corrosion resistance to sulfuric acid and good mechanical properties. In this paper, efforts to optimize the alloys performance are presented along with progress toward the development of a wrought version of the material. It was found that an appropriate heat treatment provides the largest improvement in the cast Ni–Si alloy microstructure. Trials have resulted in more than a 50% reduction by the cold rolling process. This process not only increases homogenization but also results in a more uniform distribution of G-phase particles, which is beneficial for the improvements in ductility and corrosion resistance. These alloys have great potential for use in future hydrogen production as well as fossil energy combustion.

99 GENERAL AND MISCELLANEOUS↗

Microstructure, Processing, Performance Relationships for High Temperature Coatings

HVOF coatings have shown high resistance to corrosion in fossil energy applications and it is generally accepted that mechanical failure, e.g. cracking or spalling, ultimately will determine coating lifetime. The high velocity oxygen-fuel method (HVOF) for applying coatings is one of the most commercially viable and allows the control of various parameters including powder particle velocity and temperature which influence coating properties, such as residual stress, bond coat strength and microstructure. The mechanical durability of coatings is being assessed using a dual eddy current coil method to monitor crack formation in real time during thermal cycling. Absolute impedence signals from two coils, which interrogate two different areas on the sample, are collected. Crack detection can be determined from the differential signal generated from these absolute signals. The coils are operated at two different frequencies, resulting in two differential signals used for crack detection. Currently this crack detection method is being used to elucidate the influence of thermal cycling temperature and coating thickness on cracking. Recent results (cycles to failure) will be presented for FeAl coatings thermally sprayed (HVOF) onto carbon steel to two coating thicknesses (160 microns and 250 microns thick) and subsequently cycled at temperatures up to 700oC. Thinner coatings exhibit greater resistance to cracking. Ultimately the resistance to cracking will be used to explore the relationship between HVOF spraying parameters, the mechanical properties of the coating and coating bond strength to develop optimized thermal spray parameters. To this end thermal spray coatings (FeAl and Fe3Al) have been applied to additional alloy substrates (Grade 91 steel, 316 SS, etc.) relevant to the fossil industry. Future plans also include a direct comparison to conventional weld overlay coatings currently used in the industry as well as exploration of new coatings. The room temperature mechanical strength and coating adhesion to the substrate is also of considerable importance. Eddy current methods are being developed to detect coating failure during room temperature tensile tests to optimize surface preparation as well as aid in the optimization of the HVOF thermal spray parameters.

20 FOSSIL-FUELED POWER PLANTS↗