Engineering Papers⌕ Search

Engineering topics

Lienert, U

Publications and source records attributed to Lienert, U.

At least 19 records

High-energy diffraction microscopy at the advanced photon source

The status of the High Energy Diffraction Microscopy (HEDM) program at the 1-ID beam line of the Advanced Photon Source is reported. HEDM applies high energy synchrotron radiation for the grain and sub-grain scale structural and mechanical characterization of polycrystalline bulk materials in situ during thermomechanical loading. Case studies demonstrate the mapping of grain boundary topology, the evaluation of stress tensors of individual grains during tensile deformation and comparison to a finite element modeling simulation, and the characterization of evolving dislocation structure. Complementary information is obtained by post mortem electron microscopy on the same sample volume previously investigated by HEDM.

43 PARTICLE ACCELERATORS↗

Validation of a crystal plasticity model using high energy diffraction microscopy

High energy diffraction microscopy is used to measure the crystallographic orientation and evolution of lattice strain in an Al-Li alloy. The relative spatial arrangement of the several pancake-shaped grains in a tensile sample is determined through in situ and ex situ techniques. A model for crystal plasticity with continuity of lattice spin is posed, where grains are represented by layers in a finite element mesh following the arrangement indicated by experiment. Comparison is drawn between experiment and simulation.

36 MATERIALS SCIENCE↗

Statistics of High Purity Nickel Microstructure From High Energy X-ray Diffraction Microscopy

We have measured and reconstructed via forward modeling a small volume of microstructure of high purity, well annealed nickel using high energy x-ray diffraction microscopy (HEDM). Statistical distributions characterizing grain orientations, intra-granular misorientations, and nearest neighbor grain misorientations are extracted. Results are consistent with recent electron backscatter diffraction measurements. Peaks in the grain neighbor misorientation angle distribution at 60 degrees ({Sigma}3) and 39 degrees ({Sigma}9) have resolution limited widths of {approx} 0.14 degree FWHM. The analysis demonstrates that HEDM can recover grain and grain boundary statistics comparable to OIM volume measurements; more extensive data sets will lead to full, five parameter grain boundary character distributions. Due to its non-destructive nature, HEDM can then watch, both statistically and through tracking of individual grains and boundaries, the evolution of such distributions with processing of the sample.

43 PARTICLE ACCELERATORS↗

Reversal of asymmetry of x-ray peak profiles from individual grains during a strain path change.

X-ray peak profiles are measured from individual bulk grains during tensile deformation. Two differently oriented copper samples pre-deformed in tension show the expected peak profile asymmetry caused by intra-grain stresses. One of the samples is oriented to achieve a significant change of the intra-grain stresses during in situ tensile loading and this is observed as a reversal of the sign of the peak profile asymmetry.

36 MATERIALS SCIENCE↗

Load partitioning between single bulk grains in a two-phase duplex stainless steel during tensile loading.

The lattice strain tensor evolution for single bulk grains of austenite and ferrite in a duplex stainless steel during tensile loading to 0.02 applied strain has been investigated using in situ high-energy X-ray measurements and finite-element modeling. Single-grain X-ray diffraction lattice strain data for the eight austenite and seven ferrite grains measured show a large variation of residual lattice strains, which evolves upon deformation to the point where some grains with comparable crystallographic orientations have lattice strains different by 1.5 x 10{sup -3}, corresponding to a stress of -300MPa. The finite-element simulations of the 15 measured grains in three different spatial arrangements confirmed the complex deformation constraint and importance of local grain environment.

36 MATERIALS SCIENCE↗

In situ measurements of x-ray peak profile asymmetry from individual grains.

Two copper samples, pre-deformed in tension to 5% plastic strain, are subjected to an in situ tensile deformation of 1% plastic strain while X-ray peak profiles from individual bulk grains are obtained. One sample is oriented with the in situ tensile axis parallel to the pre-deformation axis, and peak profiles are obtained with the scattering vector parallel to this direction. The profiles show the expected asymmetry explained by the composite model as caused by intra-grain stresses. The other sample is oriented with the in situ tensile axis perpendicular to the pre-deformation axis, and peak profiles are obtained with the scattering vector parallel to the in situ tensile axis. In this case the profiles initially show an opposite asymmetry, but during the in situ deformation the asymmetry reverses sign as the deformation under new loading conditions leads to changes in the intra-grain stresses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Evolution of deformation structures under varying loading conditions followed in-situ by high angular resolution 3DXRD.

With high angular resolution three-dimensional X-ray diffraction, individual subgrains are traced in the bulk of a polycrystalline specimen and their dynamics is followed in situ during varying loading conditions. The intensity distribution of single Bragg reflections from an individual grain is analyzed in reciprocal space. It consists of sharp high-intensity peaks arising from subgrains superimposed on a cloud of lower intensity arising from dislocation walls. Individual subgrains can be distinguished by their unique combination of orientation and elastic strain. The responses of polycrystalline copper to different loading conditions are presented: during uninterrupted tensile deformation, formation of subgrains can be observed concurrently with broadening of the Bragg reflection shortly after onset of plastic deformation. With continued tensile deformation, the subgrain structure develops intermittently. When the traction is terminated, stress relaxation occurs and number, size and orientation of subgrains are found to be constant. The subgrain structure freezes and only a minor clean-up of the dislocation structure is observed. When changing the tensile direction after pre-deformation in tension, a systematic correlation between the degree of strain path change and the changes in the dislocation structure quantified by the volume fraction of the subgrains is established. For obtaining the subgrain volume fraction, a new fitting method has been developed for partitioning the contributions of subgrains and dislocation walls.

36 MATERIALS SCIENCE↗

In-situ single-grain peak profile measurements on Ti-7Al during tensile deformation.

High-energy three-dimensional X-ray diffraction with medium and high reciprocal space resolution was applied to study in situ tensile deformation of Ti-7Al specimens. Samples with planar and random dislocation microstructures were prepared and characterized by electron microscopy. Stress tensors of individual grains were obtained at several loads up to 2% deformation. The stress tensors were found to rotate, and resolved shear stresses were calculated. High-resolution reciprocal space maps of selected grains were recorded. Azimuthal and radial distributions were visualized and discussed in terms of idealized dislocation structures. Heterogeneous grain rotations were observed for the planar microstructure and found to be consistent with activation of the highest stressed basal slip system. Intra-granular strain gradients were detected in excess of the intrinsic radial dislocation peak broadening. The potential of combining the applied techniques with modeling to obtain multiple length-scale information during deformation of bulk specimens is discussed.

36 MATERIALS SCIENCE↗

Evolution of stress in individual grains and twins in a magnesium alloy aggregate.

This is an in situ measurement of the full stress tensor and its evolution in a growing deformation twin and, simultaneously, in the grain where the twin forms. The combined information provides a detailed picture of the grain-twin interaction. The three-dimensional x-ray diffraction method using 80.7 keV synchrotron x rays allows us to in situ investigate a grain within the bulk of a magnesium alloy (AZ31) sample that is compressed to activate the {l_brace}10{bar 1}2{r_brace} <{bar 1}011> tensile twin system. We observe that the stress state of the twin is drastically different from the one of the grain in which it is embedded. We analyze such result in terms of the shear transformation associated with twinning and the dimensional constraints imposed by the surrounding aggregate.

36 MATERIALS SCIENCE↗

Load partitioning and strain-induced martensite formation during tensile loading of a metastable austenitic stainless steel.

In-situ high-energy X-ray diffraction and material modeling are used to investigate the strain-rate dependence of the strain-induced martensitic transformation and the stress partitioning between austenite and {alpha}{prime} martensite in a metastable austenitic stainless steel during tensile loading. Moderate changes of the strain rate alter the strain-induced martensitic transformation, with a significantly lower {alpha}{prime} martensite fraction observed at fracture for a strain rate of 10{sup -2} s{sup -1}, as compared to 10{sup -3} s{sup -1}. This strain-rate sensitivity is attributed to the adiabatic heating of the samples and is found to be well predicted by the combination of an extended Olson-Cohen strain-induced martensite model and finite-element simulations for the evolving temperature distribution in the samples. In addition, the strain-rate sensitivity affects the deformation behavior of the steel. The {alpha}{prime} martensite transformation at high strains provides local strengthening and extends the time to neck formation. This reinforcement is witnessed by a load transfer from austenite to {alpha}{prime} martensite during loading.

36 MATERIALS SCIENCE↗

Residual stress distribution in steel butt welds measured using neutron and synchrotron diffraction.

70 keV synchrotron radiation and thermal neutrons have been employed to investigate the residual stress characteristics in a fully restrained, steel, butt weld. The focus is on the values of the subsurface and through-thickness strain/stress variation in the middle of the weld. The advantages and limitations of the techniques have been addressed, in relation to the gauge volume, the stress-free reference sample and positioning. The measurement of residual stress around the weld achieved in this work significantly improves the resolution at which residual stress in welded components has been determined.

36 MATERIALS SCIENCE↗

Statistics of high purity nickel microstructure from high energy x-ray diffraction microscopy.

We have measured and reconstructed via forward modeling a small volume of microstructure of high purity, well annealed nickel using high energy xray diffraction microscopy (HEDM). Statistical distributions characterizing grain orientations, intra-granular misorientations, and nearest neighbor grain misorientations are extracted. Results are consistent with recent electron backscatter diffraction measurements. Peaks in the grain neighbor misorientation angle distribution at 60 degrees (S3) and 39 degrees (S9) have resolution limited widths of {approx}0:14 degree FWHM. The analysis demonstrates that HEDM can recover grain and grain boundary statistics comparable to OIM volume measurements; more extensive data sets will lead to full, five parameter grain boundary character distributions. Due to its non-destructive nature, HEDM can then watch, both statistically and through tracking of individual grains and boundaries, the evolution of such distributions with processing of the sample.

36 MATERIALS SCIENCE↗