Engineering Papers⌕ Search

Engineering topics

Li, S X

Publications and source records attributed to Li, S X.

Shear viscosity to entropy density ratio in the Boltzmann-Uehling-Uhlenbeck model

The ratio of shear viscosity ({eta}) to entropy density (s) for an equilibrated system is investigated in intermediate-energy heavy-ion collisions below 100A MeV within the framework of the Boltzmann-Uehling-Uhlenbeck model. After the collision system almost reaches a local equilibration, the temperature, pressure and energy density are obtained from the phase-space information and {eta}/s is calculated using the Green-Kubo formulas. The results show that {eta}/s decreases with incident energy and tends toward a smaller value around 0.5, which is not so drastically different from the BNL Relativistic Heavy Ion Collider results in the present model.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Evaluation of 2.25Cr-1Mo Alloy for Containment of LiCl/KCl Eutectic during the Pyrometallurgical Processing of Used Nuclear Fuel

Recovery of uranium from the Mk-IV and Mk-V electrorefiner vessels containing a LiCl/KCl eutectic salt has been on-going for 14 and 12 years, respectively, during the pyrometallurgical processing of used nuclear fuel. Although austenitic stainless steels are typically utilized for LiCl/KCl salt systems, the presence of cadmium in the Mk-IV electrorefiner dictates an alternate material. A 2.25Cr-1Mo alloy (ASME SA-387) was chosen due to the absence of nickel in the alloy which has a considerable solubility in cadmium. Using the transition metal impurities (iron, chromium, nickel, molybdenum, and manganese) in the electrorefined uranium products, an algorithm was developed to derive values for the contribution of the transition metals from the various input sources. Weight loss and corrosion rate data for the Mk-V electrorefiner vessel were then generated based on the transition metal impurities in the uranium products. To date, the corrosion rate of the 2.25Cr-1Mo alloy in LiCl/KCl eutectic is outstanding assuming uniform (i.e. non-localized) conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Separation and Recovery of Uranium Metal from Spent Light Water Reactor Fuel via Electrolytic Reduction and Electrorefining

A series of bench-scale experiments was performed in a hot cell at Idaho National Laboratory to demonstrate the separation and recovery of uranium metal from spent light water reactor (LWR) oxide fuel. The experiments involved crushing spent LWR fuel to particulate and separating it from its cladding. Oxide fuel particulate was then converted to metal in a series of six electrolytic reduction runs that were performed in succession with a single salt loading of molten LiCl – 1 wt% Li2O at 650 °C. Analysis of salt samples following the series of electrolytic reduction runs identified the diffusion of select fission products from the spent fuel to the molten salt electrolyte. The extents of metal oxide conversion in the post-test fuel were also quantified, including a nominal 99.7% conversion of uranium oxide to metal. Uranium metal was then separated from the reduced LWR fuel in a series of six electrorefining runs that were performed in succession with a single salt loading of molten LiCl-KCl-UCl3 at 500 °C. Analysis of salt samples following the series of electrorefining runs identified additional partitioning of fission products into the molten salt electrolyte. Analyses of the separated uranium metal were performed, and its decontamination factors were determined.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fate of Noble Metals during the Pyroprocessing of Spent Nuclear Fuel

During the pyroprocessing of spent nuclear fuel by electrochemical techniques, fission products are separated as the fuel is oxidized at the anode and refined uranium is deposited at the cathode. Those fission products that are oxidized into the molten salt electrolyte are considered active metals while those that do not react are considered noble metals. The primary noble metals encountered during pyroprocessing are molybdenum, zirconium, ruthenium, rhodium, palladium, and technetium. Pyroprocessing of spent fuel to date has involved two distinctly different electrorefiner designs, in particular the anode to cathode configuration. For one electrorefiner, the anode and cathode collector are horizontally displaced such that uranium is transported across the electrolyte medium. As expected, the noble metal removal from the uranium during refining is very high, typically in excess of 99%. For the other electrorefiner, the anode and cathode collector are vertically collocated to maximize uranium throughput. This arrangement results in significantly less noble metals removal from the uranium during refining, typically no better than 20%. In addition to electrorefiner design, operating parameters can also influence the retention of noble metals, albeit at the cost of uranium recovery. Experiments performed to date have shown that as much as 100% of the noble metals can be retained by the cladding hulls while affecting the uranium recovery by only 6%. However, it is likely that commercial pyroprocessing of spent fuel will require the uranium recovery to be much closer to 100%. The above mentioned design and operational issues will likely be driven by the effects of noble metal contamination on fuel fabrication and performance. These effects will be presented in terms of thermal properties (expansion, conductivity, and fusion) and radioactivity considerations. Ultimately, the incorporation of minor amounts of noble metals from pyroprocessing into fast reactor metallic fuel will be shown to be of no consequence to reactor performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Integrated Efficiency Test for Pyrochemical Fuel Cycles

An engineering-scale integrated efficiency test was conducted with sodium-bonded, spent EBR-II drive fuel elements. The major pieces of equipment involved in the test were the element chopper, Mk-IV electrorefiner, cathode processor, and casting furnace. Four electrorefining batches (containing 50.4 kg HM) were processed under a set of fixed operating parameters that have been developed for the equipment based on over a decade’s worth of processing experience. A mass balance around this equipment was performed. Actinide dissolution and recovery efficiencies were established based on the mass balance and chemical analytical results of various samples taken from process streams during the integrated efficiency test.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Actinide Recovery Experiments with Bench-Scale Liquid Cadmium Cathode in Fission Product-Laden Molten Salt

This article summarizes the observations and analytical results from a series of bench- scale liquid cadmium cathode experiments that recovered transuranic elements together with uranium from a molten electrolyte laden with real fission products. Variable parameters such as the ratio of Pu3+/U3+ in the electrolyte, liquid cadmium cathode voltage, and feed materials were tested in the LCC experiments. Actinide recovery efficiency and Pu/U ratio in the liquid cadmium cathode product under variable conditions are reported in the article. Separation factors for actinides and rare earth elements in the salt/cadmium system are also presented.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Determining Bond Sodium Remaining in Plenum Region of Spent Nuclear Driver Fuel

The Fuel Conditioning Facility (FCF) at the Idaho National Laboratory (INL) treats spent nuclear fuel using an electro-chemical process that separates the uranium from the fission products, sodium thermal bond, and cladding materials [REF 1]. Upon immersion into the ER electrolyte, the sodium used to thermally bond the fuel to the clad jacket chemically reacts with the UCl3 in the electrolyte producing NaCl and uranium metal. The uranium in the spent fuel is separated from the cladding and fission products by taking advantage of the electro-chemical potential differences between uranium and the other fuel components. Assuming all the sodium in the thermal bond is converted to NaCl in the ER, the difference between the cumulative bond sodium mass in the fuel elements and the cumulative sodium mass found in the driver ER electrolyte inventory provides an upper mass limit for the sodium that migrated to the upper gas region, or plenum section, of the fuel element during irradiation in the reactor. The plenums are to be processed as metal waste via melting and metal consolidation operations. However, depending on the amount of sodium in the plenums, additional processing may be required to remove the sodium before metal waste processing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Engineering-Scale Liquid Cadmium Cathode Experiments

Recovery of uranium and transuranic (TRU) actinides from spent nuclear fuel by an electrorefining process was investigated as part of the U.S. Department of Energy Advanced Fuel Cycle Initiative. Experiments were performed in a shielded hot cell at the Materials and Fuels Complex at Idaho National Laboratory. The goal of these experiments was to collect, by an electrochemical process, kilogram quantities of uranium and plutonium into what is called a liquid cadmium cathode (LCC). For each experiment, a steel basket loaded with chopped spent nuclear fuel from the Experimental Breeder Reactor II acted as the anode in the electrorefiner. The cathode was a beryllium oxide crucible containing ~26 kg of cadmium metal (the LCC). In the three experiments performed to date, between 1 and 2 kg of heavy metal was collected in the LCC after passing an integrated current between 1.80 and 2.16 MC (500 and 600 A h) from the anode to the cathode. Sample analysis of the processed LCC ingots measured detectable amounts of TRUs and rare earth elements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗