Engineering topics

Li, Nami

Publications and source records attributed to Li, Nami.

9 records

DOE OSTI2024

HL-2A's ELM cycle simulations by integrating BOUT++'s drift MHD and transport code

A new integrating model has been developed to couple tokamak edge multiscale magnetohydrodynamic (MHD) events and transport simulations, such as edge-localized mode (ELM) cycles. As a proof of principle, we first start from a set of three-field two-fluid model equations, which includes the pressure, current, and vorticity. Here, the equations are separated into the slowly evolving part of the axisymmetric component by taking a time average of the axisymmetric component. The time-averaged fluxes, which are quadratic in fluctuating quantities, act as driven terms for the time-averaged axisymmetric quantities that determine the plasma transport, and therefore the large-scale evolution of the plasma profiles. Then the HL-2A's ELM cycles are simulated using the model. Good agreements of ELM size and pedestal recovery time have been achieved for the solutions obtained from the coupled simulation compared with experiment. For one ELM cycle simulation, the coupled code can achieve a speedup of a factor of up to 30 over standalone code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Characterization of SOL profiles and turbulence in ICRF-heated plasmas in EAST

Scrape-off layer (SOL) profiles and turbulence in ion cyclotron range of frequency (ICRF)-heated plasmas are investigated by the reciprocating probe diagnostic system (FRPs) and gas puff imaging (GPI) diagnostic in EAST. A radio-frequency (RF) sheath potential reaching up to 100 V is identified proximate to the ICRF antennas. Notably, the amplitude of this RF sheath potential escalates in response to rising ICRF power and inversely with plasma density. When a RF sheath is present in the far SOL, a pronounced density ‘shoulder’ forms in front of the ICRF antennas, while the ‘shoulder’ fade away as the antenna and associated RF sheath shift outwards. A strong E r shear is revealed by measurements from both FRPs and GPI. Analysis of the poloidal wave number-frequency spectrum reveals suppression of high-frequency turbulence in the far SOL due to the RF sheath. This effect is manifested in the reduced autocorrelation time τ c and reduced average blob size δ blob of the SOL plasma. Intriguingly, the poloidal propagation direction of the low-frequency turbulence reverses from the electron to the ion diamagnetic drift direction at the RF sheath location. A surge of tungsten impurity is potentially attributed to the heightened interaction between the SOL plasmas and the wall material. Shifting the ICRF antennas outward, to alleviate heat spots, results in the relocation of the RF sheath to the shaded region of the main limiter. This shift amplifies the radial velocity of blobs in the far SOL and concurrently diminishes the SOL density when compared to conditions without ICRF injection. The properties of ion saturation current fluctuations are consistent with the stochastic model predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Turbulence spreading effects on the ELM size and SOL width

BOUT++ turbulence simulations were performed to investigate the impact of turbulence spreading on the edge localized mode (ELM) size and divertor heat flux width (λ q ) broadening in small ELM regimes. Here, this study is motivated by EAST experiments. BOUT++ linear simulations of a pedestal radial electric field (E r ) scan show that the dominant toroidal number mode (n) shifts from high-n to low-n, with a narrow mode spectrum, and the maximum linear growth rate increases as the pedestal E r well deepens. The nonlinear simulations show that as the net E × B pedestal flow increases, the pressure fluctuation level and its inward penetration beyond the top of the pedestal both increase. This leads to a transition from small ELMs to large ELMs. Both inward and outward turbulence spreading are sensitive to the scrape-off-layer (SOL) plasma profiles. The inward turbulence spreading increases for the steep SOL profiles, leading to increasing pedestal energy loss in the small ELM regime. The SOL width (λ q ) is significantly broadened progressing from the ELM-free to small ELM regime, due to the onset of strong radial turbulent transport. The extent of the SOL width (λ q ) broadening depends strongly on outward turbulence spreading. The fluctuation energy intensity flux Γ ε at the separatrix can be enhanced by increasing either pedestal E r flow shear or local SOL pressure gradient. The λ q is broadened as the fluctuation energy intensity flux Γ ε at the last close flux surface (LCFS) increases. Local SOL E × B flow shear will restrain outward turbulence spreading and the associated heat flux width broadening. Operating in H-mode with small ELMs has the potential to solve two critical problems: reducing the ELM size and broadening the SOL width.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Simulation of the impact of particle recycling on the plasma in MPS-LD device based on the BOUT++ LPD module

A linear plasma device (LPD) module has been developed under the BOUT++ framework to simulate plasma transport in the MPS-LD. However, previously, the LPD module used a simplistic neutral particle model that only includes particle density and velocity, which prevents the full understanding of the plasma-neutrals interactions. In this work, we further optimize the neutral model by using a more complete neutral fluid model containing the continuity equation, momentum equation, and energy equation. The reactions such as charge exchange, excitation, and radiation collisions are included. Since the neutral particle source is mainly provided by particle recycling from the target, a particle recycling model is employed, which includes both fast reflection and slow thermal release. The upgraded LPD module is applied to simulate the argon (Ar) discharge experiment of MPS-LD, and the benchmark against experiment measurement and SOLPS-ITER simulation results are presented. Good agreements are obtained, showing the validation of the upgraded module. After that, the impact of particle recycling on Ar plasma is investigated. It is found that a higher recycling coefficient (R) promotes the achievement of high-density plasma at the target. In conclusion, the recycled Ar atoms change target plasma pressure as well as plasma-neutral collisions, which both contribute to plasma momentum loss, thus promoting the rollover of ion flux to the target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Impact of pedestal density gradient and collisionality on ELM dynamics

BOUT++ turbulence simulations are conducted to capture the underlying physics of small ELM characteristics achieved by increasing separatrix density via controlling strike points from vertical to horizontal divertor plates for three EAST discharges. BOUT++ linear simulations show that the most unstable modes change from high-n ideal ballooning modes to intermediate-n peeling–ballooning modes and eventually to peeling–ballooning stable plasmas in the pedestal. Nonlinear simulations show that the fluctuation is saturated at a high level for the lowest separatrix density. The ELM size decreases with increasing separatrix density, until the fraction of this energy lost during the ELM crash becomes less than 1% of the pedestal stored energy, leading to small ELMs. Simulations indicate that small ELMs can be triggered either by the marginally peeling–ballooning instability near the peak pressure gradient position inside the pedestal or by a local instability in the pedestal foot with a larger separatrix density gradient. The pedestal collisionality scan for type-I ELMs with steep pedestal density gradient shows that both linear growth rate and ELM size decrease with increasing collisionality. On the contrary, the pedestal collisionality and pedestal density width scan with a weak pedestal density gradient indicate small ELMs can either be triggered by a high-n ballooning mode or by a low-n peeling mode in a low collisionality region 0.04–0.1. We report the simulations indicate the weaker the linear unstable modes near marginal stability with small linear growth rate, the lower nonlinearly saturated fluctuation intensity and the smaller turbulence spreading from the linear unstable zone to stable zone in the nonlinear saturation phase, leading to small ELMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Data-driven model for divertor plasma detachment prediction

We present a fast and accurate data-driven surrogate model for divertor plasma detachment prediction leveraging the latent feature space concept in machine learning research. Our approach involves constructing and training two neural networks: an autoencoder that finds a proper latent space representation (LSR) of plasma state by compressing the multi-modal diagnostic measurements and a forward model using multi-layer perception (MLP) that projects a set of plasma control parameters to its corresponding LSR. By combining the forward model and the decoder network from autoencoder, this new data-driven surrogate model is able to predict a consistent set of diagnostic measurements based on a few plasma control parameters. In order to ensure that the crucial detachment physics is correctly captured, highly efficient 1D UEDGE model is used to generate training and validation data in this study. The benchmark between the data-driven surrogate model and UEDGE simulations shows that our surrogate model is capable of providing accurate detachment prediction (usually within a few per cent relative error margin) but with at least four orders of magnitude speed-up, indicating that performance-wise, it has the potential to facilitate integrated tokamak design and plasma control. Comparing with the widely used two-point model and/or two-point model formatting, the new data-driven model features additional detachment front prediction and can be easily extended to incorporate richer physics. This study demonstrates that the complicated divertor and scrape-off-layer plasma state has a low-dimensional representation in latent space. Understanding plasma dynamics in latent space and utilising this knowledge could open a new path for plasma control in magnetic fusion energy research.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Simulation of plasma transport in MPS-LD linear plasma device by using BOUT++

Here a linear plasma device (LPD) module based on the 2D transport module under the BOUT++ framework is developed in this paper to simulate plasma transport in the LPD. The LPD module includes three parts, i.e. magnetic field calculation, simulation mesh generation and plasma transport setup. The magnetic field is calculated with the circular current loop using the location and current information of each coil. The mesh generation code can produce a simulation mesh for LPD by employing the magnetic field. The plasma transport model is based on the reduced Braginskii equations, which consist of the continuity equation, momentum equation, and energy equation. The fluid neutral model is applied for neutral particle simulation. Deuterium (D) and helium (He) ions and atoms can be simulated by the model. The first attempt to simulate plasma transport in the new LPD, called multiple plasma simulation linear plasma device (MPS-LD), is presented using the developed model. The D plasma transport in the MPS-LD is simulated and benchmarked against the two-point model, showing the validation of the BOUT++ simulation. The effects of radial transport on the heat load to the target are studied, which illustrates the significant impact of the radial diffusivities $D_⟂$ and $\mathcal{X}_{⟂i,e}$ on the plasma. Moreover, the He impurity injection process during the discharge is studied with emphasis on plasma–impurity interactions. The simulation results show that He injection can reduce the plasma energy load to the target significantly, and the efficiency depends on the He source density and injection velocity. The present work provides an alternative and flexible simulation tool for plasma transport in LPDs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Characteristics of grassy ELMs and their impact on the divertor heat flux width

We report BOUT++ turbulence simulations are conducted for a 60 s steady-state long pulse high β p EAST grassy ELM discharge. BOUT++ linear simulations show that the unstable mode spectrum covers a range of toroidal mode numbers from low-n (n = 10–15) peeling–ballooning modes (P–B) to high-n (n = 40–80) drift-Alfvén instabilities. Nonlinear simulations show that the ELM crash is triggered by low-n peeling modes and fluctuation is generated at the peak pressure gradient position and radially spread outward into the scrape-off-layer, even though the drift-Alfvén instabilities dominate the linear growth phase. However, drift-Alfvén turbulence delays the onset of the grassy ELM and enhances the energy loss with the fluctuation extending to pedestal top region. Simulations further show that if the peeling drive is removed, the fluctuation amplitude drops by an order of magnitude and the ELM crashes disappear. The divertor heat flux width is ~2 times larger than the estimates based on the HD model and the Eich's ITPA multi-tokamak scaling (or empirical Eich scaling) due to the strong radial turbulence transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Modeling of small tungsten dust grains in EAST tokamak with NDS-BOUT ++

In order to investigate the transport of small dusts as well as their evolution property along their trajectories, the NDS module is developed under the BOUT++ framework, a highly desirable C++ code package to perform parallel plasma fluid simulations with an arbitrary number of equations in three-dimensional curvilinear coordinates. Due to the severe dust ablation in fusion plasmas, the dust size would decrease from micrometer to nanometer, resulting in impurities. Small dusts in the simulations here are specified as tungsten spheres with the radii on or below the order of submicrometer. The Rayleigh limit is included in the charging process when the dust is ablated to the droplet phase. The simulation results from the NDS module show that a 200 nm radius spherical tungsten dust originated from upper divertor region of EAST Tokamak is ablated completely due to the intense heating from the incoming plasma inside the core region, well consistent with the CCD footage of EAST shot # 81459. Furthermore it is found that the magnetic field dominates the dust transport when the dust radius is below 100 nm during the ablation along the trajectory. Our simulations predict that a 10 nm radius spherical tungsten dust injected from the inner midplane is well constrained by the magnetic field, and it reaches the inner divertor target with a velocity on the order of km/s.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗