Centralized, decentralized, and independent control of a flexible manipulator on a flexible base
Explore the source record for details and available documents.
Li, Feiyue↗
Engineering topics
Li, Feiyue
Publications and source records attributed to Li, Feiyue.
Centralized, decentralized, and independent control of a flexible manipulator on a flexible base
The dynamics and control of a flexible manipulator arm with payload mass on a flexible base in space are considered. The controllers are provided by one torquer at the center of the base and one torquer at the connection joint of the robot and the base. The nonlinear dynamics of the system is modeled by applying the finite element method and Lagrangian formula. Three control strategies are considered and compared, i.e., centralized control, decentralized control, and independent control. All these control designs are based on the linear quadratic regulator theory. A mathematical decomposition is used in the decentralization process so that the coupling between the subsystems is weak, while a physical decomposition is used in the independent control design process. For both the decentralized and the independent controls, the stability of the overall linear system is checked before a numerical simulations is initiated. Two numerical examples show that the response of the independent control system are close to those of the centralized control system, while the responses of the decentralized control system are not.
Li, Feiyue↗
Maneuver simulations of flexible spacecraft by solving TPBVP
The optimal control of large angle rapid maneuvers and vibrations of a Shuttle mast reflector system is considered. The nonlinear equations of motion are formulated by using Lagrange's formula, with the mast modeled as a continuous beam. The nonlinear terms in the equations come from the coupling between the angular velocities, the modal coordinates, and the modal rates. Pontryagin's Maximum Principle is applied to the slewing problem, to derive the necessary conditions for the optimal controls, which are bounded by given saturation levels. The resulting two point boundary value problem (TPBVP) is then solved by using the quasilinearization algorithm and the method of particular solutions. In the numerical simulations, the structural parameters and the control limits from the Spacecraft Control Lab Experiment (SCOLE) are used. In the 2-D case, only the motion in the plane of an Earth orbit or the single axis slewing motion is discussed. In the 3-D slewing, the mast is modeled as a continuous beam subjected to 3-D deformations. The numerical results for both the linearized system and the nonlinear system are presented to compare the differences in their time response.
Bainum, Peter M.↗
The dynamics and control of large flexible space structures - 13
The optimal control of three-dimensional large angle maneuvers and vibrations of a Shuttle-mast-reflector system is considered. The nonlinear equations of motion are formulated by using Lagrange's formula, with the mast modeled as a continuous beam subject to three-dimensional deformations. Pontryagin's Maximum Principle is applied to the slewing problem, to derive the necessary conditions for the optimal controls, which are bounded by given saturation levels. The resulting two point boundary value problem is then solved by using the quasilinearization algorithm and the method of particular solutions. The study of the large angle maneuvering of the Shuttle-beam-reflector spacecraft in the plane of a circular earth orbit is extended to consider the effects of the structural offset connection, the axial shortening, and the gravitational torque on the slewing motion. Finally the effect of additional design parameters (such as related to additional payload requirement) on the linear quadratic regulator based design of an orbiting control/structural system is examined.
Bainum, Peter M.↗
Numerical approach for solving rigid spacecraft minimum time attitude maneuvers
Explore the source record for details and available documents.
Li, Feiyue↗
Rapid in-plane maneuvering of the flexible orbiting SCOLE
The rapid two-dimensional slewing and vibrational control of the unsymmetrical flexible SCOLE (Spacecraft Control Laboratory Experiment) with multi-bounded controls has been considered. Pontryagin's Maximum Principle has been applied to the nonlinear equations of the system to derive the necessary conditions for the optimal control. The resulting two-point boundary-value problem is then solved by using the quasilinearization technique, and the near-minimum time is obtained by sequentially shortening the slewing time until the controls are near the bang-bang type. The trade-off between the minimum time and the minimum flexible amplitude requirements has been discussed. The numerical results show that the responses of the nonlinear system are significantly different from those of the linearized system for rapid slewing.
Bainum, Peter M.↗
An improved shooting method for solving minimum-time maneuver problems
The minimum-time attitude maneuvers of a rigid spacecraft are considered. Generally, the associated nonsingular, nonlinear two-point boundary-value problem, derived by using Pontryagin's Maximum Principle, can be solved through shooting methods to find the switching times for the bang-bang control. However, a good initial guess for the missing initial costates is important because the convergence range of the initial costates is very narrow, especially when a multi-bang-bang control strategy is needed. This paper proposes a numerical approach to generate the initial costates so that they are very close to the converged values. The initial costates are first generated by using a recently developed quasi-linearization technique for the near-minimum-time problem and then reduced in magnitude, through some properly designed scales, before the shooting method is used. Numerical examples indicate the closeness of the results from these two techniques (quasi-linearization and shooting).
Li, Feiyue↗
Effects of structural offset, axial shortening, and gravitational torque on the slewing of a flexible spacecraft
The large-angle maneuvering of a Shuttle-beam-reflector spacecraft in the plane of a circular earth orbit is examined by considering the effects of the structural offset connection, the axial shortening, and the gravitational torque on the slewing motion. The offset effect is analyzed by changing the attachment point of the reflector to the beam. As the attachment point is moved away from the mass center of the reflector, the responses of the nonlinear system deviate from those of the linearized system. The axial geometric shortening effect induced by the deformation of the beam contributes to the system equations through second order terms in the modal amplitudes and rates. The gravitational torque effect is relatively small.
Li, Feiyue↗
The dynamics and control of large flexible space structures - 12, supplement 11
The rapid 2-D slewing and vibrational control of the unsymmetrical flexible SCOLE (Spacecraft Control Laboratory Experiment) with multi-bounded controls is considered. Pontryagin's Maximum Principle is applied to the nonlinear equations of the system to derive the necessary conditions for the optimal control. The resulting two point boundary value problem is then solved by using the quasilinearization technique, and the near minimum time is obtained by sequentially shortening the slewing time until the controls are near the bang-bang type. The tradeoff between the minimum time and the minimum flexible amplitude requirements is discussed. The numerical results show that the responses of the nonlinear system are significantly different from those of the linearized system for rapid slewing. The SCOLE station-keeping closed loop dynamics are re-examined by employing a slightly different method for developing the equations of motion in which higher order terms in the expressions for the mast modal shape functions are now included. A preliminary study on the effect of actuator mass on the closed loop dynamics of large space systems is conducted. A numerical example based on a coupled two-mass two-spring system illustrates the effect of changes caused in the mass and stiffness matrices on the closed loop system eigenvalues. In certain cases the need for redesigning control laws previously synthesized, but not accounting for actuator masses, is indicated.
Bainum, Peter M.↗
Use of the quasilinearization algorithm for the simulation of LSS slewing
The use of the Maximum Principle for the large angle slewing of large space structures (LSS) usually results in the so-called two-point boundary-value problem, in which many requirements (e.g., minimum time, small amplitude, and limited control power, etc.) must be satisfied simultaneously. The successful solution of this problem depends largely on the use of an efficient numerical algorithm. There are many candidate algorithms available for this problem (e.g., quasilinearization, gradient, etc.). Here researchers discuss only the quasilinearization method which has been used for several cases of large angle slewing of LSS. The basic idea of this algorithm is to make a series of successive approximations of the solution from a particular solvable case (linear or nonlinear) to a more general practical case. For the rigid spacecraft slewing problem with no constraints on the controls, the solution procedure can be found in the literature. This procedure needs to be modified if a minimum time for the slewing problem is desired with control limits given. Recently, an indirect method for finding the minimum time was developed to meet all these requirements. For the general mixed (including both rigid and flexible parts) problem, an additional constraint of small vibrational amplitude on the flexible parts is imposed.
Li, Feiyue↗
The dynamics and control of the in-orbit SCOLE configuration
The study of the dynamics of the Spacecraft Control Laboratory Experiment (SCOLE) is extended to emphasize the synthesis of control laws for both the linearized system as well as the large amplitude slewing maneuvers required to rapidly reorient the antenna line of sight. For control of the system through small amplitude displacements from the nominal equilibrium position LQR techniques are used to develop the control laws. Pontryagin's maximum principle is applied to minimize the time required for the slewing of a general rigid spacecraft system. The minimum slewing time is calculated based on a quasi-linearization algorithm for the resulting two point boundary value problem. The effect of delay in the control input on the stability of a continuously acting controller (designed without considering the delay) is studied analytically for a second order plant. System instability can result even for delays which are only a small fraction of the natural period of motion.
Bainum, Peter M.↗
The dynamics and control of large flexible space structures, part 11
A mathematical model is developed to predict the dynamics of the proposed Spacecraft Control Laboratory Experiment during the stationkeeping phase. The Shuttle and reflector are assumed to be rigid, while the mass connecting the Shuttle to the reflector is assumed to be flexible with elastic deformations small as compared with its length. It is seen that in the presence of gravity-gradient torques, the system assumes a new equilibrium position primarily due to the offset in the mass attachment point to the reflector from the reflector's mass center. Control is assumed to be provided through the Shuttle's three torquers and throught six actuators located by painrs at two points on the mass and at the reflector mass center. Numerical results confirm the robustness of an LQR derived control strategy during stationkeeping with maximum control efforts significantly below saturation levels. The linear regulator theory is also used to derive control laws for the linearized model of the rigidized SCOLE configuration where the mast flexibility is not included. It is seen that this same type of control strategy can be applied for the rapid single axis slewing of the SCOLE through amplitudes as large as 20 degrees. These results provide a definite trade-off between the slightly larger slewing times with the considerable reduction in over-all control effort as compared with the results of the two point boundary value problem application of Pontryagin's Maximum Principle.
Bainum, Peter M.↗
Minimum time attitude slewing maneuvers of a rigid spacecraft
The minimum time attitude slewing motion of a rigid spacecraft with its controls provided by torques and forces, which have their upper and lower limits prescribed, is considered. The two-point boundary-value problem is derived by applying the Pontriagin's Maximum Principle to the system and solved by using a quasi-linearization algorithm. The nominal solutions to the problem as well as the starting values of the total slewing time and the unknown initial costates for this algorithm are generated by using Euler's eigenaxis rotation theorem. It is pointed out that one of the four initial costates associated with the quaternions can be arbitrarily selected without affecting the optimal controls and, thus, simplifying the computation. The minimum slewing time is determined by shortening the total slewing time until at least one of the controls becomes a bang-bang type. Several numerical tests for the rigidized SCOLE model are presented to show the applications of the methods.
Li, Feiyue↗
The dynamics and control of large flexible space structures X, part 1
The effect of delay in the control system input on the stability of a continuously acting controller which is designed without considering the delay is studied. The stability analysis of a second order plant is studied analytically and verified numerically. For this example it is found that the system becomes unstable for a delay which is equivalent to only 16 percent of its natural period of motion. It is also observed that even a small amount of natural damping in the system can increase the amount of delay that can be tolerated before the onset of instability. The delay problem is formulated in the discrete time domain and an analysis procedure suggested. The maximum principle from optimal control theory is applied to minimize the time required for the slewing of a general rigid spacecraft. The slewing motion need not be restricted to a single axis maneuver. The minimum slewing time is calculated based on a quasi-linearization algorithm for the resulting two point boundary value problem. Numerical examples based on the rigidized in-orbit model of the SCOLE also include the more general reflector line-of-sight slewing maneuvers.
Bainum, Peter M.↗
Issues in modeling and controlling the SCOLE configuration
The parametric study of the in-plane Spacecraft Control Laboratory Experiment (SCOLE) system, the Floquet Stability Analysis, and three dimensional formulations of the SCOLE system dynamics are examined. Control issues are discussed, such as: control of large structures with delayed input in continuous time; control with delayed input in discrete time; control law design for SCOLE using Linear Quadratic Gaussian (LQC)/TRR technique; and optimal torque control for SCOLE slewing maneuvers.
Bainum, Peter M.↗
Optimal torque control for SCOLE slewing maneuvers
The Spacecraft Control Laboratory Experiment (SCOLE) was slewed from one attitude to the required attitude and an integral performance index which involves the control torques was minimized. Kinematic and dynamical equations, optimal control, two-point boundary-value problems, and estimation of unknown boundary conditions are presented.
Bainum, P. M.↗
Minimum time attitude slewing maneuvers of a rigid spacecraft
The problems of large-angle attitude maneuvers of a spacecraft have gained much consideration in recent years. The configurations of the spacecraft considered are: completely rigid, a combination of rigid and flexible parts, or gyrostat-type systems. The performance indices usually include minimum torque integration, power criterion, and frequency-shaped cost functionals. The minimum time slewing problem of a rigid spacecraft was examined. Optimal control theory (Maximum Principal) was applied to the slewing motion of a general rigid spacecraft. Control torque about all three axes was computed. The equations for the system are composed of the Euler dynamical equations in the spacecraft body axes and the quaternion kinematical equation. By introducing the costates for the quaternion and the angular velocity, the Hamiltonian of the system can be formed and the optimal control obtained. Finally the methods are applied to the SCOLE slewing motion. The control variables include three control moments on the Shuttle and two control forces on the reflector. Numerical results are discussed.
Li, Feiyue↗