Levy, Ralph | Engineering Papers

NASA NTRS1991

A design strategy for the use of vortex generators to manage inlet-engine distortion using computational fluid dynamics

A reduced Navier-Stokes solution technique was successfully used to design vortex generator installations for the purpose of minimizing engine face distortion by restructuring the development of secondary flow that is induced in typical 3-D curved inlet ducts. The results indicate that there exists an optimum axial location for this installation of corotating vortex generators, and within this configuration, there exists a maximum spacing between generator blades above which the engine face distortion increases rapidly. Installed vortex generator performance, as measured by engine face circumferential distortion descriptors, is sensitive to Reynolds number and thereby the generator scale, i.e., the ratio of generator blade height to local boundary layer thickness. Installations of corotating vortex generators work well in terms of minimizing engine face distortion within a limited range of generator scales. Hence, the design of vortex generator installations is a point design, and all other conditions are off design. In general, the loss levels associated with a properly designed vortex generator installation are very small; thus, they represent a very good method to manage engine face distortion. This study also showed that the vortex strength, generator scale, and secondary flow field structure have a complicated and interrelated influence over engine face distortion, over and above the influence of the initial arrangement of generators.

Anderson, Bernhard H.↗

NASA NTRS1991

A design strategy for the use of vortex generators to manage inlet-engine distortion using computational fluid dynamics

A reduced Navier-Stokes solution technique was successfully used to design vortex generator installations for the purpose of minimizing engine face distortion by restructuring the development of secondary flow that is induced in typical 3-D curved inlet ducts. The results indicate that there exists an optimum axial location for this installation of corotating vortex generators, and within this configuration, there exists a maximum spacing between generator blades above which the engine face distortion increases rapidly. Installed vortex generator performance, as measured by engine face circumferential distortion descriptors, is sensitive to Reynolds number and thereby the generator scale, i.e., the ratio of generator blade height to local boundary layer thickness. Installations of corotating vortex generators work well in terms of minimizing engine face distortion within a limited range of generator scales. Hence, the design of vortex generator installations is a point design, and all other conditions are off design. In general, the loss levels associated with a properly designed vortex generator installation are very small; thus, they represent a very good method to manage engine face distortion. This study also showed that the vortex strength, generator scale, and secondary flow field structure have a complicated and interrelated influence over engine face distortion, over and above the influence of the initial arrangement of generators.

Anderson, Bernhard H.↗

NASA NTRS1991

Vortex generator design for aircraft inlet distortion as a numerical optimization problem

Aerodynamic compatibility of aircraft/inlet/engine systems is a difficult design problem for aircraft that must operate in many different flight regimes. Takeoff, subsonic cruise, supersonic cruise, transonic maneuvering, and high altitude loiter each place different constraints on inlet design. Vortex generators, small wing like sections mounted on the inside surfaces of the inlet duct, are used to control flow separation and engine face distortion. The design of vortex generator installations in an inlet is defined as a problem addressable by numerical optimization techniques. A performance parameter is suggested to account for both inlet distortion and total pressure loss at a series of design flight conditions. The resulting optimization problem is difficult since some of the design parameters take on integer values. If numerical procedures could be used to reduce multimillion dollar development test programs to a small set of verification tests, numerical optimization could have a significant impact on both cost and elapsed time to design new aircraft.

Anderson, Bernhard H.↗

NASA NTRS1991

Optimization of transistor design including large signal device/circuit interactions at extremely high frequencies (20-100+GHz)

Transistor design for extremely high frequency applications requires consideration of the interaction between the device and the circuit to which it is connected. Traditional analytical transistor models are to approximate at some of these frequencies and may not account for variations of dopants and semiconductor materials (especially some of the newer materials) within the device. Physically based models of device performance are required. These are based on coupled systems of partial differential equations and typically require 20 minutes of Cray computer time for a single AC operating point. A technique is presented to extract parameters from a few partial differential equation solutions for the device to create a nonlinear equivalent circuit model which runs in approximately 1 second of personal computer time. This nonlinear equivalent circuit model accurately replicates the contact current properties of the device as computed by the partial differential solver on which it is based. Using the nonlinear equivalent circuit model of the device, optimization of systems design can be performed based on device/circuit interactions.

Levy, Ralph↗

NASA NTRS1988

User's manual for PEPSIG NASA tip vortex version

The tip vortex flowfield plays a significant role in the performance of advanced aircraft propellers. The flowfield in the tip region is complex, three-dimensional and viscous with large secondary velocities. A computer code was developed to predict the tip vortex flowfield of advanced aircraft propellers. This document is the user's manual. The analysis and a series of test cases are presented in NASA-CR-182179.

Tsai, Tommy M.↗

NASA NTRS1988

Computation of the tip vortex flowfield for advanced aircraft propellers

The tip vortex flowfield plays a significant role in the performance of advanced aircraft propellers. The flowfield in the tip region is complex, three-dimensional and viscous with large secondary velocities. An analysis is presented using an approximate set of equations which contains the physics required by the tip vortex flowfield, but which does not require the resources of the full Navier-Stokes equations. A computer code was developed to predict the tip vortex flowfield of advanced aircraft propellers. A grid generation package was developed to allow specification of a variety of advanced aircraft propeller shapes. Calculations of the tip vortex generation on an SR3 type blade at high Reynolds numbers were made using this code and a parametric study was performed to show the effect of tip thickness on tip vortex intensity. In addition, calculations of the tip vortex generation on a NACA 0012 type blade were made, including the flowfield downstream of the blade trailing edge. Comparison of flowfield calculations with experimental data from an F4 blade was made. A user's manual was also prepared for the computer code (NASA CR-182178).

Tsai, Tommy M.↗

NASA NTRS1987

Duct flows with swirl

The physics of the flow interaction between swirl and secondary flow was studied in duct bends relevant to the design of advanced aircraft nozzle systems. Both laminar and turbulent subsonic flows were investigated in generic duct bends for different amounts of swirl. The flow calculations are based on an economical three-dimensional spatial marching method employed in an existing computer code (PEPSIG). The computational method and code were extended to allow azimuthal periodicity and solutions in which the polar coordinate singularity occurs in the interior of the flow field. These extensions are needed to address swirling flow and twisted centerlines arising in out-of-plane bends. It was found that appropriate amounts of swirl can reduce total pressure loss relative to nonswirling cases. This conclusion was found to be insensitive to computational mesh.

Tsai, Tommy M.↗

NASA NTRS1987

Design of Optimum Ducts Using an Efficient 3-D Viscous Computational Flow Analysis

Design of fluid dynamically efficient ducts is addressed through the combination of an optimization analysis with a three-dimensional viscous fluid dynamic analysis code. For efficiency, a parabolic fluid dynamic analysis was used. Since each function evaluation in an optimization analysis is a full three-dimensional viscous flow analysis requiring 200,000 grid points, it is important to use both an efficient fluid dynamic analysis and an efficient optimization technique. Three optimization techniques are evaluated on a series of test functions. The Quasi-Newton (BFGS, eta = .9) technique was selected as the preferred technique. A series of basic duct design problems are performed. On a two-parameter optimization problem, the BFGS technique is demonstrated to require half as many function evaluations as a steepest descent technique.

Madabhushi, Ravi K.↗