Engineering topics

Levine, S. R.

Publications and source records attributed to Levine, S. R..

At least 37 records · Page 2

NASA NTRS1981

Advanced aircraft engine materials trends

Recent activities of the Lewis Research Center are reviewed which are directed toward developing materials for rotating hot section components for aircraft gas turbines. Turbine blade materials activities are directed at increasing metal temperatures approximately 100 C compared to current directionally solidified alloys by use of oxide dispersion strengthening or tungsten alloy wire reinforcement of nickel or iron base superalloys. The application of thermal barrier coatings offers a promise of increasing gas temperatures an additional 100 C with current cooling technology. For turbine disk alloys, activities are directed toward reducing the cost of turbine disks by 50 percent through near net shape fabrication of prealloyed powders as well as towards improved performance. In addition, advanced alloy concepts and fabrication methods for dual alloy disks are being studied as having potential for improving the life of future high performance disks and reducing the amount of strategic materials required in these components.

Dreshfield, R. L.↗

NASA NTRS1980

Thermal barrier coatings for heat engine components

A comprehensive NASA-Lewis program of coating development for aircraft gas turbine blades and vanes is presented. Improved ceramic layer compositions are investigated, along the MCrAlY bond films and the methods of uniform deposition of the coatings; the thermomechanical and fuel impurity tolerance limits of the coatings are being studied. Materials include the ZrO2-Y2O3/NiCrAlY system; the effects of the bond coat and zirconia composition on coating life and Mach 1 burner rig test results are discussed. It is concluded that Diesel engines can also utilize thermal barrier coatings; they have been used successfully on piston crowns and exhaust valves of shipboard engines to combat lower grade fuel combustion corrosion.

Levine, S. R.↗

NASA NTRS1980

Corrosion-resistant ceramic thermal barrier coating

Two-layer thermal barrier coating, consisting of metal-CrA1Y bond coating and calcium silicate ceramic outer layer, greatly improves resistance of turbine parts to hot corrosion from fuel and air impurities. Both layers can be plasma sprayed, and ceramic layer may be polished to reduce frictional losses. Ceramic provides thermal barrier, so parts operate cooler metal temperatures, coolant flow can be reduced, or gas temperatures increased. Lower grade fuels also can be used.

Hodge, P. E.↗

NASA NTRS1980

Thermal barrier coatings - Burner rig hot corrosion test results

A Mach 0.3 burner rig test program was conducted to examine the sensitivity of thermal barrier coatings to Na- and V-contaminated combustion gases simulating potential utility gas turbine environments. Coating life of the standard ZrO2-12Y2O3/Ni-16.2Cr-5.6Al-0.6Y (composition in wt %) NASA thermal barrier coating system which was developed for aircraft gas turbines was significantly reduced in such environments. Two thermal barrier coating systems, Ca2SiO4/Ni-16.2Cr-5.6Al-0.6Y and ZrO2-8Y2O3/Ni-16.4Cr-5.1Al-0.15Y and a less insulative cermet coating system, 50 vol % MgO-50 vol % Ni-19.6Cr-17.1Al-0.97Y/Ni-16.2Cr-5.6Al-0.6Y, were identified as having much improved corrosion resistance compared to the standard coating.

Hodge, P. E.↗

NASA NTRS1980

Thermal barrier coatings for aircraft gas turbines

Improvements in gas turbine performance are approaching the limits imposed by alloy properties and excessive cooling air requirements. Thin ceramic coatings can increase the difference between gas temperature and metal temperature by several hundred degrees. Thus, they are potentially a major step forward in surface protection. These coatings offer the potential to reduce fuel consumption by permitting reduced coolant flow or higher turbine inlet temperature or to improve durability by reducing metal temperatures and transient thermal stresses. At NASA Lewis, in-house and contractual programs are in place to bring this promising technology to engine readiness in the early 1980's. Progress towards this goal is summarized in this paper.

Miller, R. A.↗

NASA NTRS1980

Thermal barrier coatings for superalloys

The current status of ceramic thermal barrier coatings for protection of turbine airfoil components is reviewed. Test results for an early duplex coating system ZrO2-12% Y2O3/Ni-16% Cr-6% Al-0.6% Y, improved system ZrO2-8% Y2O3/Ni-17% Cr-5% Al-0.35% Y, and air/fuel impurity tolerant systems based on ZrO2-8% Y2O3, 2CaO-SiO2, and a MgO-NiCrAlY cermet are discussed. Preliminary test results at 800 C for a graded ZrO2-8% Y2O3/Ni-20% Cr-11% Al-0.4% Y coating system show that the coating can survive at least 500 hr in the presence of 50 ppm V plus other fuel contaminants and additives.

Miller, R. A.↗

NASA NTRS1979

Materials and structures technology

Materials and structures performance limitations, particularly for the hot section of the engine in which these limitations limit the life of components, are considered. Failure modes for components such as blades, vanes, and combustors and how they are affected by the environment for such components are discussed. Methods used to improve the materials used for such components are: (1) application of directional structures to turbine components for high strength at high temperatures; (2) improved coatings to increase oxidation and corrosion resistance; (3) increase strength and stiffness with reduced weight by applying higher specific properties of composite materials; and (4) cost effective processing such as near net shape powder methods applied to disks. Life prediction techniques developed to predict component life accurately in advance of service and progress in improving the intermediate and cold section components of turbine engines are covered.

Signorelli, R. A.↗

NASA NTRS1978

Thermal barrier coatings: Burner rig hot corrosion test results

A Mach 0.3 burner rig test program was conducted to examine the sensitivity of thermal barrier coatings to Na and V contaminated combustion gases simulating potential utility gas turbine environments. Coating life of the standard ZrO2-12Y2O3/Ni-16.2Cr-5.6Al-0.6Y NASA thermal barrier coating system which was developed for aircraft gas turbines was significantly reduced in such environments. Two thermal barrier coating systems, Ca2SiO4/Ni-16.2Cr-5.6Al-0.6Y and ZrO2-8Y2O3/Ni-16.4Cr-5.1Al-0.15Y and a less insulative cermet coating system, 50 volume percent MgO-50 volume percent Ni-19.6Cr-17.1Al-0.97Y/Ni-16.2Cr-5.6Al-0.6Y, were identified as having much improved corrosion resistance compared to the standard coating.

Hodge, P. E.↗

NASA NTRS1978

Reaction diffusion in the NiCrAl and CoCrAl systems

The paper assesses the effect of overlay coating and substrate composition on the kinetics of coating depletion by interdiffusion. This is accomplished by examining the constitution, kinetics and activation energies for a series of diffusion couples primarily of the NiCrAl/Ni-10Cr or CoCrAl/Ni-10Cr type annealed at temperatures in the range 1000-1205 C for times up to 500 hr. A general procedure is developed for analyzing diffusion in multicomponent multiphase systems. It is shown that by introducing the concept of beta-source strength, which can be determined from appropriate phase diagrams, the Wagner solution for consumption of a second phase in a semiinfinite couple is successfully applied to the analysis of MCrAl couples. Thus, correlation of beta-recession rate constants with couple composition, total and diffusional activation energies, and interdiffusion coefficients are determined.

Levine, S. R.↗

NASA NTRS1978

Adhesive/cohesive strength of a ZrO2.1-2 w/o Y2O3/NiCrAIY thermal barrier coating

The room temperature adhesive/cohesive strength of a 0.05 cm thick ZrO2.12w/oY2O3/0.013 cm thick NiCrAlY thermal barrier coating system (TBC) was investigated. The weakest link was the oxide/NiCrAlY interface region with a strength of 6.2 MN/sq m. The fracture was about half cohesive oxide failure, half oxide/NiCrAlY adhesive failure and 1 percent cohesive NiCrAlY failure. The TBC failed in a similar manner in 950 C tensile and compression tests. The oxide stripped from the TBC had a cohesive strength of 24.6 MN/sq m. The NiCrAlY had a cohesive strength of 25.1 MN/sq m. The NiCrAlY and oxide failed primarily at interparticle boundaries.

Levine, S. R.↗

NASA NTRS1978

High temperature surface protection

Alloys of the MCrAlX type are the basis for high temperature surface protection systems in gas turbines. M can be one or more of Ni, Co, or Fe and X denotes a reactive metal added to enhance oxide scale adherence. The selection and formation as well as the oxidation, hot corrosion and thermal fatigue performance of MCrAlX coatings are discussed. Coatings covered range from simple aluminides formed by pack cementation to the more advanced physical vapor deposition overlay coatings and developmental plasma spray deposited thermal barrier coatings.

Levine, S. R.↗

NASA NTRS1978

Thermal Barrier Coatings

Thermal barrier coatings offer gas turbines one way to reach fuel flexibility and improved efficiency. Test/analytical results are encouraging for this young technology.

Grisaffe, S. J.↗

NASA NTRS1977

Reaction diffusion in the nickel-chromium-aluminum and cobalt-chromium-aluminum systems

The effects of MCrAl coating-substrate interdiffusion on oxidation life and the general mutliphase, multicomponent diffusion problem were examined. Semi-infinite diffusion couples that had sources representing coatings and sinks representing gas turbine alloys were annealed at 1,000, 1,095, 1,150, or 1,205 C for as long as 500 hours. The source and sink aluminum and chromium contents and the base metal (cobalt or nickel) determined the parabolic diffusion rate constants of the couples and predicted finite coating lives. The beta source strength concept provided a method (1) for correlating beta recession rate constants with composition; (2) for determining reliable average total, diffusion, and constitutional activation energies; and (3) for calculating interdiffusion coefficients.

Levine, S. R.↗

NASA NTRS1977

Thermal barrier coatings: A near term, high payoff technology

The present status of thermal barrier coatings is reviewed including both experimental results and forecasts of the benefits derived from use of these coatings in aircraft and utility gas turbines. The potential of thermal barrier coatings relative to structural ceramics is discussed along with a development plan for these coatings.

Levine, S. R.↗

NASA NTRS1976

Hot hardness of nickel-rich nickel-chromium-aluminum alloys

Rockwell A hardness of cast nickel-chromium-aluminum (NiCrAl) alloys was examined from ambient to 1150 K and compared to cast NiAl and IN-100. Alloy constitution was either gamma, gamma prime + gamma or gamma + beta + alpha + gamma prime. Below 1000 K beta containing NiCrAl alloys have hardnesses comparable to IN-100; above 1000 K they soften faster than IN-100. At 1150 K the hardness of beta-containing NiCrAl alloys decreases with increasing beta-content. The beta-containing NiCrAl alloys were harder than beta-NiAl. The ultimate tensile strengths of the NiCrAl alloys were estimated. The effects of NiCrAl coatings on strength and fatigue life of cooled turbine components were deduced.

Levine, S. R.↗

NASA NTRS1976

Toward more environmentally resistant gas turbines - Progress in NASA-Lewis programs

The paper surveys programs for improving the environmental resistance of gas turbine and power system materials to oxidation and hot corrosion. A computer program Corest has been produced which provides an initial method for predicting long-time metal loss using short-time oxidation data. The role of the coefficient of thermal expansion mismatch on oxide spallation is being studied. A paralinear oxidation attack model in conjunction with regression analysis of weight change data has been applied to the study of oxidation and hot corrosion attack of some Ni-Cr-Al system alloys. Oxide-dispersion strengthened alloys based on the Ni-Cr-Al system are being developed. Sodium sulfate formation during turbine combustion is being investigated from a thermodynamic viewpoint.

Lowell, C. E.↗

NASA NTRS1976

Toward more environmentally resistant gas turbines: Progress in NASA-Lewis programs

A wide range of programs are being conducted for improving the environmental resistance to oxidation and hot corrosion of gas turbine and power system materials. They range from fundamental efforts to delineate attack mechanisms, allow attack modeling and permit life prediction, to more applied efforts to develop potentially more resistant alloys and coatings. Oxidation life prediction efforts have resulted in a computer program which provides an initial method for predicting long time metal loss using short time oxidation data by means of a paralinear attack model. Efforts in alloy development have centered on oxide-dispersion strengthened alloys based on the Ni-Cr-Al system. Compositions have been identified which are compromises between oxidation and thermal fatigue resistance. Fundamental studies of hot corrosion mechanisms include thermodynamic studies of sodium sulfate formation during turbine combustion. Information concerning species formed during the vaporization of Na2SO4 has been developed using high temperature mass spectrometry.

Lowell, C. E.↗

NASA NTRS1974

Performance of coated columbium and tantalum alloys in plasma arc reentry simulation tests

The evaluation of coated refractory metals screened in stagnation model plasma arc tests is reported. Columbium alloys FS-85, C-129Y, and Cb-752 coated with Si-20Cr-20Fe (R512E) were tested at 1390 C. Three silicide coatings on Ta-10W were tested at 1470 C. Half-hour cycles and a 6500 N/sqm stagnation pressure were used. The best R512E coated columbium alloy was FS-85 with first local coating breakdowns occurring in 12 to 50 cycles. At coating defects, low metal recession rates (0.005 mm/min) were generally observed on coated columbium alloys while high rates (0.15 mm/min) were observed on coated Ta-10W. Coated columbium suffered large emittance losses (to below 0.7) due to surface refractory metal pentoxide formation.

Levine, S. R.↗