Engineering Papers⌕ Search

Engineering topics

Lerche, E

Publications and source records attributed to Lerche, E.

Heat loads from ICRF and LH wave absorption in the SOL: characterization on JET and implications for the ITER-Like Wall

Heat loads from ICRF and LH wave absorption in the SOL are characterized on JET from the de-convolution of surface temperatures measured by infrared thermography. The spatial localization, quantitative estimates, parametric dependence and physical origin of the observed heat fluxes are documented. Implications of these observations are discussed for the operation of JET with an ITER-Like Wall, featuring Beryllium tiles with reduced power handling capability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ICRF scenarios for ITER's half-field phase

The non-active operation phase of ITER will be done in H and {sup 4}He plasmas at half the nominal magnetic field, B{sub 0} = 2.65T. At this field and for the given frequency range of the ICRF system (f = 40-55MHz), three ICRF heating scenarios are available a priori: (i) Fundamental ICRH of majority H plasmas at f{approx_equal}40MHz,(ii) second harmonic (N= 2) {sup 3}He ICRH in H plasmas at f{approx_equal}53MHz and (iii) fundamental minority H heating in {sup 4}He plasmas at f{approx_equal}40MHz. While the latter is expected to perform well for not too large H concentrations, the heating scenarios available for the Hydrogen plasmas are less robust. Recent JET experiments performed in similar conditions to those expected in ITER's half-field phase confirmed the low performance of these two scenarios and numerical simulations have shown that the situation is not much improved in ITER, mainly because of the rather modest plasma temperature and density expected in its initial operation phase. A summary of the main experimental results obtained at JET followed by numerical predictions for ITER's half-field ICRF heating scenarios will be presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ICRF heating at JET: From operations with a metallic wall to the long term perspective of a DT campaign

The first series of experiments with the ITER-like wall (ILW) will start mid-2011 with D plasmas and will continue through 2012-13 with H, {sup 4}He and D plasmas, and up to 2014-15, when a DT campaign is proposed. In this paper, the previous experience at JET is reviewed to set the scene for the future challenges of ICRF operation including change in the ICRF coupling, W impurity production and evaluation of localized power loads due the RF sheaths. development in a Beryllium/Tungsten environment of ICRF heating schemes for the non activated and the DT phases of ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhancing The Mode Conversion Efficiency In JET Plasmas With Multiple Mode Conversion Layers

The constructive interference effect described by Fuchs et al. [1] shows that the mode conversion and thereby the overall heating efficiency can be enhanced significantly when an integer number of fast wave wavelengths can be folded in between the high field side fast wave cutoff and the ion-ion hybrid layer(s) at which the ion Bernstein or ion cyclotron waves are excited. This effect was already experimentally identified in ({sup 3}He)-D plasmas [2] and was recently tested in ({sup 3}He)-H JET plasmas. The latter is an 'inverted' scenario, which differs significantly from the ({sup 3}He)-D scenarios since the mode-conversion layer is positioned between the low field side edge of the plasma and the ion-cyclotron layer of the minority {sup 3}He ions (whereas the order in which a wave entering the plasma from the low field side encounters these layers is inverted in a 'regular' scenario), and because much lower {sup 3}He concentrations are needed to achieve the mode-conversion heating regime. The presence of small amounts of {sup 4}He and D in the discharges gave rise to an additional mode conversion layer on top of the expected one associated with {sup 3}He-H, which made the interpretation of the results more complex but also more interesting: Three different regimes could be distinguished as a function of X[{sup 3}He], and the differing dynamics at the various concentrations could be traced back to the presence of these two mode conversion layers and their associated fast wave cutoffs. Whereas (1-D and 2-D) numerical modeling yields quantitative information on the RF absorptivity, recent analytical work by Kazakov [3] permits to grasp the dominant underlying wave interaction physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High frequency fast wave current drive for DEMO

A steady-state tokamak reactor (SSTR) requires a high efficiency current drive system, from plug to driven mega-amps. RF systems working in the ion-cyclotron range of frequencies (ICRF) have high efficiency from plug to antenna but a limited current drive (CD) efficiency and centrally peaked CD profiles. The latter feature is not adequate for a SSTR where the current should be sufficiently broad to keep the central safety factor (possibly significantly) above 1. In addition, the fact that the fast wave (FW) is evanescent at the edge limits coupling, requiring high voltage operation, which makes the system dependent on plasma edge properties and prone to arcing, reducing its reliability. A possible way to overcome these weaknesses is to operate at higher frequency (10 times or more the cyclotron frequency). The advantages are: (1) The coupling can be much better (waves propagate in vacuum) if the parallel refractive index n{sub ||} is kept below one, (2) The FW group velocity tends to align to the magnetic field, so the power circumnavigates the magnetic axis and can drive off-axis current, (3) Due to the latter property, n{sub ||} can be upshifted along the wave propagation path, allowing low n{sub ||} launch (hence good coupling, large CD efficiency) with ultimately good electron absorption (which requires higher n{sub ||}. Note however that the n{sub ||} upshift is a self-organized feature, that electron absorption is in competition with {alpha}-particle absorption and that uncoupling of the FW from the lower hybrid resonance at the edge requires n{sub ||} slightly above one. The latter possibly counterproductive features might complicate the picture. The different aspects of this potentially attractive off-axis FWCD scheme are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Interaction of ICRF Fields with the Plasma Boundary in AUG and JET and Guidelines for Antenna Optimization

W sputtering during ICRF on ASDEX Upgrade (AUG) and temperature rise on JET A2 antenna septa are considered in connection with plasma conditions at the antenna plasma facing components and E{sub parallel} near-fields. Large antenna-plasma clearance, high gas puff and low light impurity content are favorable to reduce W sputtering in AUG. The spatial distribution of spectroscopically measured effective W sputtering yields clearly points to the existence of strong E{sub parallel} fields at the antenna box ('feeder fields') which dominate over the fields in front of the antenna straps. The picture of E{sub parallel} fields, obtained by HFSS code, corroborates the dominant role of E{sub parallel} at the antenna box on the formation of sheath-driving RF voltages for AUG. Large antenna-plasma clearance and low gas puff are favorable to reduce septum temperature of JET A2 antennas. Assuming a linear relation between the septum temperature and the sheath driving RF voltage calculated by HFSS, the changes of the temperature with dipole phasing (00{pi}{pi}, 0{pi}{pi}0 or 0{pi}0{pi}) are well described by the related changes of the RF voltages. Similarly to the AUG antenna, the strongest E{sub parallel} are found at the limiters of the JET A2 antenna for all used dipole phasings and at the septum for the phasings different from 0{pi}0{pi}. A simple general rule can be used to minimize E{sub parallel} at the antenna: image currents can be allowed only at the surfaces which do not intersect magnetic field lines at large angles of incidence. Possible antenna modifications generally rely either on a reduction of the image currents, on their short-circuiting by introducing additional conducting surfaces or on imposing the E{sub parallel} = 0 boundary condition. On the example of AUG antenna, possible options to minimize the sheath driving voltages are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

ICRF Wall Conditioning: Present Status and Developments for Future Superconducting Fusion Machines

ITER and future superconducting fusion machines need efficient wall conditioning techniques for routine operation in between shots in the presence of permanent high magnetic field for wall cleaning, surface isotope exchange and to control the in-vessel long term tritium retention. Ion Cyclotron Wall Conditioning (ICWC) based on the ICRF discharge is fully compatible and needs the presence of the magnetic field. The present paper focuses on the principal aspects of the ICWC discharge performance in large-size fusion machines: (i) neutral gas RF breakdown with conventional ICRF heating antennas, (ii) antenna coupling with low density ({approx}10{sup 17} m{sup -3}) RF plasmas and (iii) ICWC scenarios with improved RF plasma homogeneity in the radial and poloidal directions. All these factors were identified as crucial to achieve an enhanced conditioning effect (e.g. removal rates of selected 'marker' masses). All the observed effects are analyzed in terms of RF plasma wave excitation/absorption and compared with the predictions from 1-D RF full wave and 0-D RF plasma codes. Numerical modeling and empirical extrapolation from the existing machines give good evidence for the feasibility of using ICWC in ITER with the main ICRF antenna.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview on Experiments On ITER-like Antenna On JET And ICRF Antenna Design For ITER

Following an overview of the ITER Ion Cyclotron Resonance Frequency (ICRF) system, the JET ITER-like antenna (ILA) will be described. The ILA was designed to test the following ITER issues: (a) reliable operation at power densities of order 8 MW/m{sup 2} at voltages up to 45 kV using a close-packed array of straps; (b) powering through ELMs using an internal (in-vacuum) conjugate-T junction; (c) protection from arcing in a conjugate-T configuration, using both existing and novel systems; and (d) resilience to disruption forces. ITER-relevant results have been achieved: operation at high coupled power density; control of the antenna matching elements in the presence of high inter-strap coupling, use of four conjugate-T systems (as would be used in ITER, should a conjugate-T approach be used); operation with RF voltages on the antenna structures up to 42 kV; achievement of ELM tolerance with a conjugate-T configuration by operating at 3{omega} real impedance at the conjugate-T point; and validation of arc detection systems on conjugate-T configurations in ELMy H-mode plasmas. The impact of these results on the predicted performance and design of the ITER antenna will be reviewed. In particular, the implications of the RF coupling measured on JET will be discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Present Status of the ITER-like ICRF Antenna on JET

The commissioning of the ITER-Like ICRF Antenna (ILA) on JET plasmas from May 2008 to April 2009 in various conditions (33, 42 and 47 MHz, L- and H-mode, antenna strap-plasma separatrix distances of {approx}9 to 17 cm) has provided relevant information for future antenna design and operation. The maximum power density achieved was 6.2 MW/m{sup 2} in L-mode with strap to plasma separatrix distance of {approx}9-10 cm at 42 MHz on the lower half of the ILA extrapolating to 8 MW/m{sup 2} if the full generator power had been available. Efficient (trip-free operation) ELM tolerance was obtained both at 33 and 42 MHz on a large range of ELMs with strap voltages up to 42 kV and a maximum power density of 4.1 MW/m{sup 2}. The paper reviews these achievements as well as remaining issues.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

RF Matching Feedback Control Systems on the JET ITER-Like Antenna

Ion Cyclotron Resonance Frequency (ICRF) antennas achieve maximum power transfer from RF generator to plasma load by establishing an impedance match. The JET ITER-Like Antenna (ILA) consists of 4 mutually coupled resonators that need to be matched simultaneously and whose resonant states need to be accurately controlled by several available actuators to couple maximum power and to achieve optimal ELM resilience. The operation of the matching system is described. Experimental operation revealed some phenomena and sensitivities that did not surface from simulation alone and that should be taken into account for the design of future ICRF antennae systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulating the JET ITER-like Antenna circuit

A set of simulation/interpretation tools based on transmission line theory and on the RF model developed by M. Vrancken has been developed to study the ITER-like Antenna (ILA) at JET. For given tuning element settings, the unique solution of the equations governing the ILA circuit requires solving a system of coupled linear equations relating the voltages and currents at the antenna straps and other key locations. This computation allows cross-checking predicted values against measured experimental ones. Further more, a minimization procedure allows improving the correspondence with the quantities measured in the circuit during shots, thus coping with unavoidable errors arising from uncertainties in the measurements or from inaccuracies in the adopted RF model. Typical applications are e.g. fine-tuning of the second-stage of the ILA circuit for increased ELM-resilience, cross-checking the calibration of the measurements throughout the circuit and predicting the antenna performance and matching conditions in new plasma scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Operational Experience with the Scattering Matrix Arc Detection System on the JET ITER-Like Antenna

The Scattering Matrix Arc Detection System (SMAD) has been fully deployed on all 4 sets of Resonant Double Loop (RDL), Vacuum Transmission Line (VTL) and Antenna Pressurised Transmission Lines (APTL) of the JET ICRF ITER-Like Antenna (ILA) and this has been indispensable for operating at low (real) T-point impedance values to investigate ELM tolerance. This paper describes the necessity of the SMAD vs VSWR (Voltage Standing Wave Ratio) protection system, SMAD commissioning, problems and a number of typical events detected by the SMAD system during operation on plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Overview of Recent Results on Heating and Current Drive in the JET tokamak

In this paper, significant results in the heating and current drive domains obtained at JET in the past few years following systems upgrade and dedicated experimental time, will be reviewed. Firstly, an overview of the new Ion Cyclotron Resonance Frequency (ICRF) heating capabilities will be presented i.e. results from the ITER-Like ICRF antenna (ILA), the use of External Conjugate-T and 3dB hybrid couplers to increase the ICRF power during ELMy H-mode. Furthermore, experiments to study the influence of the phasing of the ICRF antenna on power absorption and coupling will be described. Looking at Low Hybrid (LH) issues for ITER, the effect of the location of gas injection on the LH coupling improvement at large launcher-separatrix distances will be discussed as the possibility to operate at ITER-relevant power densities. Experiments to characterise the LH power losses in the Scrape-Off-Layer (SOL) and to determine the LH wave absorption and current drive using power modulation will be shown. Finally, plasma rotation studies in the presence of ICRF heating with standard and enhanced JET toroidal field ripple will be presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A 2D finite element wave equation solver based on triangular base elements

A finite element method based on the subdivision of the physical domain in triangular sub-domains in which simple local 'areale' coordinates are adopted is explored. The advantage of the method is that it straightforwardly allows grid refinement in regions where higher precision is required. The plasma model was kept simple for this 'proof-of-principle' exercise. Rather than accounting for the actual differential or integro-differential dielectric tensor, its locally uniform plasma equivalent was adopted for 3 possible choices: the cold plasma response, the full hot Stix/Swanson plasma tensor retaining all orders in finite Larmor radius (FLR) and the more common hot tensor, truncated at terms of second order in the Larmor radius.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Recent experiments on alternative dipole phasing with the JET A2 ICRF antennas

Using the JET A2 ICRF antennas, experiments were carried out to assess the performance of three different dipole phasing configurations relevant for the operation of the ICRF antenna in ITER. Three similar discharges with dipole (0{pi}0{pi}), 'symmetric dipole' (0{pi}{pi}0) and 'super dipole' (00{pi}{pi}) phasings were compared. In the 'super dipole' case, higher coupling was confirmed but lower heating efficiency and much stronger plasma wall interaction were observed, as corroborated, respectively, by the analysis of the diamagnetic energy response to the ICRF power steps and by the observation of a considerable temperature rise of the antenna limiters and septa in the 00{pi}{pi} case. These observations were found to be in line with simulations of the ICRF wave absorption and with High Frequency Structure Simulator (HFSS) modelling of the RF fields near the antenna.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗