Engineering Papers⌕ Search

Engineering topics

Leonard, A.

Publications and source records attributed to Leonard, A..

At least 37 records · Page 2

Computing three-dimensional incompressible flows with vortex elements

The techniques, capabilities and applicability of numerical models of three-dimensional, unsteady vortical flows with high Re are assessed. Vorticity is calculated only in appropriate regions and the velocity field is derived from the boundary conditions. Vorticity is assumed to take the shape of tubes with uniform core structures in the case of turbulence. The efforts being made to simplify equations for dense collections of vortex filaments in order to make them tractable to computer simulations are described. The effectiveness of vorticity arrow representations for accurately describing vorticity fields near surfaces is discussed, along with Lagrangian vortex elements, which may be of use in modelling the rotational part of flows around bluff bodies, nonuniform density flows and chemically reacting flows.

Leonard, A.↗

Direct numerical simulation of equilibrium turbulent boundary layers

This paper describes the simulation of turbulent boundary layers by direct numerical solution of the three-dimensional, time-dependent Navier-Stokes equations, using a spectral method. The flow is incompressible, with Re sub delta = 1000. The equations are written in the self-similar coordinate system and periodic streamwise and spanwise boundary conditions are imposed. A family of nine 'equilibrium' boundary layers, from the strongly accelerated 'sink' flow to Stratford's separating boundary layer is treated. Good general agreement with experiments is observed. The effects of pressure gradients on the structures and statistics, both in the wall and wake regions are discussed.

Spalart, P. R.↗

Simulating a Three-Dimensional Flow in Pipes

Numerical method simulates in unsteady, incompressible flow in axisymmetric pipe in three dimensions. Method relies on velocity-vector expansion technique in which each vector function in expansion set is divergence-free and satisfies boundary conditions for viscous flow.

Leonard, A.↗

A spectral numerical method for the Navier-Stokes equations with applications to Taylor-Couette flow

A new spectral method for solving the incompressible Navier-Stokes equations in a plane channel and between concentric cylinders is presented. The method uses spectral expansions which inherently satisfy the boundary conditions and the continuity equation and yield banded matrices which are efficiently solved at each time step. In addition, the number of dependent variables is reduced, resulting in a reduction in computer memory requirements. Several test problems have been computed for the channel flow and for flow between concentric cylinders, including Taylor-Couette flow with axisymmetric Taylor vortices and wavy vortices. In all cases, agreement with available experimental and theoretical results is very good.

Moser, R. D.↗

Numerical simulation of vortex breakdown by the vortex-filament method

The vortex filament method was applied to the simulation of vortex breakdown. The principal vortex region was represented by multiple filaments, and an axial velocity component was induced by a spiral winding of the filaments. First, an accuracy check was performed for a cylindrical swirling flow with simple analytical expressions for the axial and theta velocities. The result suggests that the flow field is simulated to any accuracy by increasing the number of filaments. Second, an axisymmetric type vortex breakdown was simulated, with experimental data serving as upstream conditions. The calculated axial and theta velocity contours show the breakdown of the vortex, including a rapid change in the vortex core, followed axially by a recovery zone and then a second breakdown. When three dimensional initial data are used the second breakdown appears to be of the spiral type in correspondence with experimental observations. The present method is easily used to simulate other types of vortex breakdown or other vortex flows with axial velocity.

Nakamura, Y.↗

Numerical simulation of vortex breakdown by the vortex-filament method

The vortex-filament method was applied to the simulation of vortex breakdown. The principal vortex region was represented by multiple filaments, and an axial velocity component was induced by a spiral winding of the filaments. An accuracy check was performed for a cylindrical swirling flow with simple analytical expressions for the axial and theta velocities. The result suggests that the flow field can be simulated to any accuracy by increasing the number of filaments. An axisymmetric-type vortex breakdown was simulated, with experimental data serving as upstream conditions. The calculated axial- and theta-velocity contours show the breakdown of the vortex, including a rapid change in the vortex core, followed axially by a recovery zone and then a second breakdown. When three dimensional initial data are used the second breakdown appears to be of the spiral type in correspondence with experimental observations. The present method can easily be used to simulate other types of vortex breakdown or other vortex flows with axial velocity.

Nakamura, Y.↗

Numerical Simulation of Turbulent Fluid Flows

Numerical simulation of turbulent flows is discussed. Computational requirements for the direct simulaton of turbulence, simulation of arbitrary homogeneous flows, an expansion technique for wall bounded flows with application to pipe flow, and possibilities of flow representations or modeling techniques that allow the simulation of high Reynolds number flows with a relatively small number of dependent variables are included.

Leonard, A.↗

Numerical simulation of separated flows

A new numerical method, based on the Vortex Method, for the simulation of two-dimensional separated flows, was developed and tested on a wide range of gases. The fluid is incompressible and the Reynolds number is high. A rigorous analytical basis for the representation of the Navier-Stokes equation in terms of the vorticity is used. An equation for the control of circulation around each body is included. An inviscid outer flow (computed by the Vortex Method) was coupled with a viscous boundary layer flow (computed by an Eulerian method). This version of the Vortex Method treats bodies of arbitrary shape, and accurately computes the pressure and shear stress at the solid boundary. These two quantities reflect the structure of the boundary layer. Several versions of the method are presented and applied to various problems, most of which have massive separation. Comparison of its results with other results, generally experimental, demonstrates the reliability and the general accuracy of the new method, with little dependence on empirical parameters. Many of the complex features of the flow past a circular cylinder, over a wide range of Reynolds numbers, are correctly reproduced.

Spalart, P. R.↗

A new numerical method for the simulation of three dimensional flow in a pipe

A new numerical technique for simulating three dimensional, unsteady, incompressible pipe flows is presented and its utility and accuracy is shown. Each vector function in the expansion of the velocity field is divergence free and satisfies the boundary conditions for viscous flow. Some of the benefits of the expansion technique are that pressure is eliminated from the dynamics, only two unknowns per mesh point are required, implicit treatment of the viscous terms is provided at no extra computational cost, and no fractional time steps are required. The method uses spectral expansions: Fourier series in the azimuthal and streamwise directions, and Jacobi polynominals in the radial direction.

Leonard, A.↗

Vortex simulation of an inviscid shear layer

The accuracy of the vortex-blob method was tested by simulating a free-shear-layer instability, Kirchhoff's elliptical vortex, and a circular vortex. The main numerical parameters in the vortex-blob method are the density of the vortices, and the distribution of vorticity within each vortex core. The growth rate of a periodic unstable mode of the shear layer was calculated numerically and compared with the exact result. The error is only a few percent for about 10 rows of vortex blobs. The error is reduced by decreasing the spacing between vortices and, correspondingly, the core size. In the simulation of the motion of the elliptical vortex, the rotation of the boundary, without change of shape, and the circular particle paths of the vortical fluid were well simulated. For the circular vortex, optimum sets of parameters were obtained by comparing them with the exact velocity. The results are consistent with convergence theories of the vortex-blob method. In particular, second-order convergence is observed with a Gaussian core from velocity calculation.

Nakamura, Y.↗

A new numerical method for the simulation of three-dimensional flow in a pipe

A new numerical technique for simulating three dimensional, unsteady, incompressible pipe flows is presented and its utility and accuracy is shown. Each vector function in the expansion of the velocity field is divergence free and satisfies the boundary conditions for viscous flow. Some of the benefits of the expansion technique are that pressure is eliminated from the dynamics, only two unknowns per mesh point are required, implicit treatment of the viscous terms is provided at no extra computational cost, and no fractional time steps are required. The method uses spectral expansions: Fourier series in the azimuthal and streamwise directions, and Jacobi polynominals in the radial direction. Previously announced in STAR as N82-31644

Leonard, A.↗

Computation of separated flows by a vortex-tracing algorithm

Numerical solutions for two-dimensional, time-dependent, separated flows around bodies are obtained, using a new version of the vortex method. This method provides an efficient representation of flows involving large regions of separation. The modifications incorporated in the new version, which improve its accuracy, versatility, and computing speed, are described. The computer cost is only of the order of the 3/2 power on N, instead of N-squared, for each step with N vortices. Arbitrary shapes can be treated; a conformal mapping is not required. Special attention is paid to the viscous character of the solution and to the accurate computation of the pressure distribution at the body surface. The vortex solution for the outer flow is coupled to an inner solution for the attached part of the boundary layer. Numerical results are presented for several bluff bodies exhibiting dependence on Reynolds number, for stationary airfoils under steady or transient conditions and for oscillating airfoils, including dynamic stalls. These results are compared with other available results, analytical or experimental, and demonstrate the enhanced reliability and accuracy of the improved method.

Spalart, P. R.↗

Simulation of three-dimensional incompressible flows with a vortex-in-cell method

A new method for the numerical simulation of three-dimensional incompressible flows is described. The vortex-in-cell (VIC) method presented traces the motion of the vortex filaments in the velocity field which these filaments create. The velocity field is not calculated directly by the Biot-Savart law of interaction but by creating a mesh-record of the vorticity field, then integrating a Poisson's equation via the fast Fourier transform to generate a mesh-record of the velocity field. The computed scales of motion are assumed to be essentially inviscid. Viscous of subgrid-scale effects are incorporated into a filtering procedure in wave vector space. Results of tracing a periodic array of single vortex rings are compared with a Green's function calculation. The agreement is very good.

Couet, B.↗

Mixing layer simulation by an improved three-dimensional vortex-in-cell algorithm

An extension is presented of the three-dimensional vortex-in-cell (VIC) method that allows for the simulation of incompressible turbulent flows such as plane mixing layers and wakes with exact boundary conditions in the normal direction. The vorticity is assumed to be confined between two parallel planes and the turbulence is assumed to be homogeneous in the two directions parallel to the planes. As an application, an analysis is presented of the evolution of the plane mixing layer subjected to random two- and three-dimensional initial disturbances.

Couet, B.↗

Vortex methods for flow simulation

Recent progress in the development of vortex methods and their applications to the numerical simulation of incompressible fluid flows are reviewed. Emphasis is on recent results concerning the accuracy of these methods, improvements in computational efficiency, and the development of three-dimensional methods. Simulations of several example flows which display some of the strengths and weaknesses of vortex methods are presented.

Leonard, A.↗

Turbulent structures in wall-bounded shear flows observed via three-dimensional numerical simulators

Three recent simulations of tubulent shear flow bounded by a wall using the Illiac computer are reported. These are: (1) vibrating-ribbon experiments; (2) study of the evolution of a spot-like disturbance in a laminar boundary layer; and (3) investigation of turbulent channel flow. A number of persistent flow structures were observed, including streamwise and vertical vorticity distributions near the wall, low-speed and high-speed streaks, and local regions of intense vertical velocity. The role of these structures in, for example, the growth or maintenance of turbulence is discussed. The problem of representing the large range of turbulent scales in a computer simulation is also discussed.

Leonard, A.↗

Vortex methods for two- and three-dimensional flow simulations

The point vortex and vortex blob methods for two dimensional flows are presented. Several results are discussed concerning the numerical analysis of the latter scheme, e.g., the preservation of globally conserved quantities and the analysis of the spatial discretization error resulting from the convection of fixed blobs of vorticity. An application to the two dimensional mixing layer is briefly described. The contour dynamics method is also discussed. The simulation of three dimensional flows with vortex methods is discussed. A natural way to represent the vorticity is in the form of closed tubes of filaments of vorticity, although other schemes are examined. Applications to aircraft trailing vortices and to a turbulent spot in a laminar boundary layer are presented. Hybrid schemes that use an Eulerian mesh to solve the Poisson equation for the velocity field are discussed. The goal of these schemes is to avoid the high cost of the Biot-Savart integration if many vortex elements are used while enjoying most of the advantages of pure Lagrangian schemes.

Leonard, A.↗