Engineering Papers⌕ Search

Engineering topics

Lee, Sang Bok

Publications and source records attributed to Lee, Sang Bok.

10 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Chemical and Electrochemical Characterization of Hot–Pressed Li 6 PS 5 Cl Solid State Electrolyte: Operating Pressure–Invariant High Ionic Conductivity

Sulfide solid state electrolytes (SSE) are among the most promising materials in the effort to replace liquid electrolytes, largely due to their comparable ionic conductivities. Among the sulfide SSEs, Argyrodites (Li 6 PS 5 X, X=Cl, Br, I) further stand out due to their high theoretical ionic conductivity (~1×10 –2 S cm –1 ) and interfacial stability against reactive metal anodes such as lithium. Generally, solid state electrolyte pellets are pressed from powder feedstock at room temperature, however, pellets fabricated by cold pressing consistently result in low bulk density and high porosity, facilitating interfacial degradation reactions and allowing dendrites to propagate through the pores and grain boundaries. Here, we demonstrate the mechanical and electrochemical implications of hot-pressing standalone LPSCl SSE pellets with near-theoretical ionic conductivity, superior cycling performance, and enhanced mechanical stability. X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and x-ray diffraction spectroscopy (XRD) analysis reveal no chemical changes to the Argyrodite surface after hot pressing up to 250°C. Furthermore, we use electrochemical impedance spectroscopy (EIS) to understand mechanical stability of Argyrodite SSE pellets as a function of externally applied pressure, demonstrating for the first time pressed standalone Argyrodite pellets with near-theoretical conductivities at external pressures below 14 MPa.

25 ENERGY STORAGE↗
DOE OSTI2024

Simultaneous Solid Electrolyte Deposition and Cathode Lithiation for Thin Film Batteries and Lithium Iontronic Devices

Here we show that the deposition of the solid-state electrolyte LiPON onto films of V 2 O 5 leads to their uniform lithiation of up to 2.2 Li per V 2 O 5 , without affecting the Li concentration in the LiPON and its ionic conductivity. Our results indicate that Li incorporation occurs during LiPON deposition, in contrast to earlier mechanisms proposed to explain postdeposition Li transfer between LiPON and LiCoO 2 . We use our discovery to demonstrate symmetric thin film batteries with a capacity of >270 mAh/g, at a rate of 20C, and 1600 cycles with only 8.4% loss in capacity. We also show how autolithiation can simplify fabrication of Li iontronic transistors attractive for emerging neuromorphic computing applications. Our discovery that LiPON deposition results in autolithiation of the underlying insertion oxide has the potential to substantially simplify and enhance the fabrication process for thin film solid state Li ion batteries and emerging lithium iontronic neuromorphic computing devices.

25 ENERGY STORAGE↗
DOE OSTI2023

In Situ Raman Mapping of Si Island Electrodes and Stress Modeling as a Function of Lithiation and Size

Si is known for cracking and delamination during electrochemical cycling of a battery due to the large volume change associated with Li insertion and extraction. However, it has been found experimentally that patterned Si island electrodes that are 200 nm thick and less than 7 μm wide can deform in a purely elastic manner. Inspired by this, we performed in situ Raman stress characterization of model poly-crystalline Si island electrodes using an electrochemical cell coupled with an immersion objective lens and designed for a short working distance. A 5 μm wide Si island electrode showed a parabolic stress profile during lithiation, while for a 15 μm Si island electrode, a stress plateau in the center of the electrode was observed. A continuum model with coupled electro-chemo-mechanical (ECM) physics was established to understand the stress measurement. A qualitative agreement was reached between modeling and experimental data, and the critical size effect could be explained by the Li diffusive flux as governed by competition between the Li concentration and hydrostatic stress gradients. Below the critical size, the stress gradient drives Li toward the edges, where the electrode volume is free to expand, while above the critical size, the stress plateau inhibits Li diffusion to the edge and forces destructive stress relief by cracking. Furthermore, this work represents a promising methodology for in situ characterization of ECM coupling in battery electrodes, with suggestions provided for further improvement.

25 ENERGY STORAGE↗
DOE OSTI2023

On-Wafer Wide-Pore Anodic Aluminum Oxide

Anodized aluminum oxide (AAO) has been used as nanotemplates for nanomaterials and nanodevice fabrications. Microfabrication techniques are attracting attention for nanodevice synthesis. However, AAO requires a microfabrication-compatible substrate due to its brittleness. While there are studies that already show AAO on compatible substrates, the pore sizes may not be applicable for multicomponent nanodevices. In this study, wide pore AAOs with ohmic bottom contacts are fabricated on 76 mm Si wafers. Sputtering was used to deposit Al along with supporting layers to achieve this goal. A quiescent electropolishing technique was used to smooth the surface of Al. Standard photolithography was used to define the active area on the Al for anodization. Then 195 V two-step anodization was performed to fabricate wide pore AAOs with pore diameters ranging from 130 ± 32 nm to 400 ± 31 nm with interpore distance of 480 ± 47 nm. Furthermore, it also showed that the ordering of the pores depended on the current density over the more conventional anodization time.

25 ENERGY STORAGE↗
DOE OSTI2022

Co-sputtering of lithium vanadium oxide thin films with variable lithium content to enable advanced solid-state batteries

Advanced solid-state batteries most likely will entail aggressive structures or architectures with constraints that typically limit processing temperatures. Considering this, we have identified the importance of providing lithiated electrode materials at a modest processing temperature. Here we describe a pathway to meet this by the development of a co-sputtering process using lithium oxide and vanadium oxide targets which enables the growth of lithiated vanadium oxide (LVO) thin films for application in solid-state batteries. Analysis of the structure and film composition of samples deposited with different co-sputtering rate ratios and post-annealing shows that multiple phases of Li x V 2 O 5 likely coexist (i.e. α-, ε-, δ-, and γ-V 2 O 5 ), and that this is unchanged after electrochemical cycling. The co-sputtering process can tune the lithium content up to a highly lithiated state of at least Li 2 V 2 O 5 . Electrochemical half-cells showed a significant amount of lithium available on the first charge (delithiation of LVO). LVO samples post-annealed at 300 °C showed typical redox peaks for Li x V 2 O 5 for both one and two lithium insertion reactions, which were highly reversible in most cases. A thin-film solid-state battery prototype using LVO as a cathode had 20% of the expected capacity, although the coulombic efficiency is near 100% at a fast rate (22C). As a result, this co-sputtering technique represents an opportunity for low temperature synthesis of pre-lithiated cathodes for thin film batteries, and introduces a broader methodology of depositing metal oxides with different alkali metal contents.

25 ENERGY STORAGE↗
DOE OSTI2022

Nanoscale Li, Na, and K ion-conducting polyphosphazenes by atomic layer deposition

A key trailblazer in the development of thin-film solid-state electrolytes has been lithium phosphorous oxynitride (LiPON), the success of which has led to recent progress in thin-film ion conductors. Here we compare the structural, electrochemical, and processing parameters between previously published LiPON and NaPON ALD processes with a novel ALD process for the K analogue potassium phosphorous oxynitride (KPON). In each ALD process, alkali tert-butoxides and diethylphosphoramidate are used as precursors. To understand the ALD surface reactions, this work proposes a reaction mechanism determined by in-operando mass spectrometry for the LiPON process as key to understanding the characteristics of the APON (A = Li, Na, K) family. As expected, NaPON and LiPON share similar reaction mechanisms as their structures are strikingly similar. KPON, however, exhibits similar ALD process parameters but the resulting film composition is quite different, showing little nitrogen incorporation and more closely resembling a phosphate glass. Due to the profound difference in structure, KPON likely undergoes an entirely different reaction mechanism. Furthermore, this paper presents a comprehensive summary of ALD ion conducting APON films as well as a perspective that highlights the versatility of ALD chemistries as a tool for the development of novel thin film ion-conductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Al 2 O 3 Thin Films on Magnesium: Assessing the Impact of an Artificial Solid Electrolyte Interphase

Among the many emerging technologies under investigation as alternatives to the successful Lithium-ion battery, the magnesium battery is promising due to the wide availability of magnesium, its high volumetric capacity, and the possibility for safety improvements. One of the largest challenges facing rechargeable magnesium batteries is the formation of a passivation layer at the Mg metal anode interface when reactive species in the electrolyte are reduced at the electrode-electrolyte interface. To control the solid electrolyte interphase in Lithium batteries, protective layers called artificial solid electrolyte interphase (ASEI) layers have been successful in improving Li metal anode performance. The approach of protecting Mg metal anodes from electrolyte degradation has been demonstrated by fewer studies in the literature than Li systems. In this work, we discuss the properties of Al 2 O 3 thin films deposited using atomic layer deposition as an artificial solid electrolyte interphase at the Mg anode. Our results demonstrate that Al 2 O 3 does prevent electrolyte degradation due to the reductive nature of Mg. However, undesirable properties such as defects and layer breakdown lead to Mg growth that causes soft-shorting. The soft-shorting occurs with and without the protection layer, indicating the ALD layer does not prevent it and hinders Al 2 O 3 from being an ideal candidate for a protection layer. Crucial effects of this layer on Mg electrochemistry at the interface were observed, including growth of Mg deposits leading to soft-shorting of the cell whose morphology showed a dependence on the Al 2 O 3 layer. These results may provide guidelines for the future design and development of protective ASEI layers for Mg anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Mechanisms of Water-Stimulated Mg 2+ Intercalation in Vanadium Oxide: Toward the Development of Hydrated Vanadium Oxide Cathodes for Mg Batteries

As lithium-ion batteries approach their theoretical limits for energy density, magnesium-ion batteries are emerging as a promising next-generation energy storage technology. However, progress in magnesium-ion battery research has been stymied by a lack of available high capacity cathode materials that can reversibly insert magnesium ions. Vanadium Oxide (V 2 O 5 ) has emerged as one of the more promising candidate cathode materials, owing to its high theoretical capacity, facile synthesis methods, and relatively high operating voltage. This review focuses on the outlook of hydrated V 2 O 5 structures as a high capacity cathode material for magnesium-ion batteries. In general, V 2 O 5 structures exhibit poor experimental capacity for magnesium-ion insertion due to sluggish magnesium-ion insertion kinetics and poor electronic conductivity. However, several decades ago, it was discovered that the addition of water to organic electrolytes significantly improves magnesium-ion insertion into V 2 O 5 . This review clarifies the various mechanisms that have been used to explain this observation, from charge shielding to proton insertion, and offers an alternative explanation that examines the possible role of structural hydroxyl groups on the V 2 O 5 surface. While the mechanism still needs to be further studied, this discovery fueled new research into V 2 O 5 electrodes that incorporate water directly as a structural element. The most promising of these hydrated V 2 O 5 materials, many of which incorporate conductive additives, nanostructured architectures, and thin film morphologies, are discussed. Ultimately, however, these hydrated V 2 O 5 structures still face a significant barrier to potential applications in magnesium-ion batteries. During full cell electrochemical cycling, these hydrated structures tend to leach water into the electrolyte and passivate the surface of the magnesium anode, leading to poor cycle life and low capacity retention. Recently, some promising strides have been made to remedy this problem, including the use of artificial solid electrolyte interphase layers as an anode protection scheme, but a call to action for more anode protection strategies that are compatible with trace water and magnesium metal is required.

25 ENERGY STORAGE↗
DOE OSTI2020

Protection layers for metal anodes

A protection layer is formed on a highly-reactive substantially-pure metal anode to a thickness of between 1 nm and 200 nm, inclusive, using atomic layer deposition (ALD). The ALD protection layer allows the conduction of ions of the metal of the anode therethrough but suppresses electron transport therethrough. The ALD protection layer may also be effective to inhibit passage of air and/or water therethrough. The ALD protection layer can allow more relaxed purity requirements for subsequent battery assembly, electrolyte specifications, and/or cathode gas purity. Fabrication methods for the protection layers, protected metal anodes, and systems and devices incorporating such protected metal anodes are also disclosed herein.

Kozen, Alexander C.↗