Engineering Papers⌕ Search

Engineering topics

Lee, Richard

Publications and source records attributed to Lee, Richard.

41 records · Page 3

RF MEMS and Their Applications in NASA's Space Communication Systems

Radio frequency (RF) and microwave communication systems rely on frequency, amplitude, and phase control circuits to efficiently use the available spectrum. Phase control circuits are required for electronically scanning phase array antennas that enable radiation pattern shaping, scanning, and hopping. Two types of phase shifters, which are the phase control circuits, are most often used. The first is comprised of two circuits with different phase characteristics such as two transmission lines of different lengths or a high pass and low pass filter and a switch that directs the RF power through one of the two circuits. Alternatively, a variable capacitor, or varactor, is used to change the effective electrical path length of a transmission line, which changes the phase characteristics. Filter banks are required for the diplexer at the front end of wide band communication satellites. These filters greatly increase the size and mass of the RF/microwave systems, but smaller diplexers may be made with a low loss varactor or a group of capacitors, a switch and an inductor.

Williams, W. Daniel↗

Ultra Small Aperture Terminal for Ka-Band SATCOM

An ultra small aperture terminal (USAT) at Ka-band frequency has been developed by Lewis Research Center (LeRC) for data rates up to 1.5 Mbps in the transmit mode and 40 Mbps in receive mode. The terminal consists of a 35 cm diameter offset-fed parabolic antenna which is attached to a solid state power amplifier and low noise amplifier. A single down converter is used to convert the Ka-band frequency to 70 MHz intermediate frequency (IF). A variable rate (9.6 Kbps to 10 Mbps) commercial modem with a standard RS-449/RS-232 interface is used to provide point-to-point digital services. The terminal has been demonstrated numerous times using the Advanced Communications Technology Satellite (ACTS) and the 4.5 in Link Evaluation Terminal (LET) in Cleveland. A conceptual design for an advanced terminal has also been developed. This advanced USAT utilizes Microwave Monolithic Integrated Circuit (MMIC) and flat plate array technologies. This terminal will be self contained in a single package which will include a 1 watt solid state amplifier (SSPA), low noise amplifier (LNA) and a modem card located behind the aperture of the array. The advanced USAT will be light weight, transportable, low cost and easy to point to the satellite. This paper will introduce designs for the reflector based and array based USAT's.

Acosta, Roberto↗

Grand challenges in mass storage: A system integrator's perspective

The grand challenges are the following: to develop more innovation in approach; to expand the I/O barrier; to achieve increased volumetric efficiency and incremental cost improvements; to reinforce the 'weakest link' software; to implement improved architectures; and to minimize the impact of self-destructing technologies. Mass storage is defined as any type of storage system exceeding 100 GBytes in total size, under the control of a centralized file management scheme. The topics covered are presented in viewgraph form.

Mintz, Dan↗

Ka-band active MMIC subarray development

A 4 x 8 array consisting of two adjacent 4 x 4 MMIC subarray modules under development as part of a MMIC insertion program for the ACTS communication experiments is presented. The subarray features a high-density 'tile' configuration integrating 16 MMIC power amplifiers and 16 MMIC phase shifters. The radiating elements are cavity-backed, aperture coupled, linearly polarized microstrip patches arranged on a 4 x 4 square grid. Each module also incorporates a MMIC controller to set the phase shifts and to turn individual amplifiers 'on' or 'off'. The novel module construction technique is expected to establish a benchmark in Ka-band and higher-frequency array architectures. The hybrid integration approach used for the module can be replaced by multifunctional chips and multilayer distribution boards. The higher level of integration is to permit the dense grid spacing required for wide-angle scanning and reduced size, weight, and cost for the array.

Lee, Richard↗

An expert system for cogeneration energy system selection

A demonstration expert system has been developed which assists engineers in cogeneration energy system selection by asking them such applications-related questions as the desired electrical and thermal loads, fuel price, and electric rates. The answers given will be interfaced with the expert system's knowledge base to recommend candidate systems. Attention is given to expert system use results obtained for a sample site; their suitability is compared to that of the detailed results obtained by an earlier cogeneration system study.

Birur, G. C.↗