Engineering Papers⌕ Search

Engineering topics

Lee, R.

Publications and source records attributed to Lee, R..

35 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Scale model acoustic testing of counterrotating fans

The UDF contrarotating propfan has been subjected to scale model wind tunnel testing to ascertain both general performance and acoustic characteristics data bases. Model Propulsion Simulator test rigs able to mount contrarotating fan blades of up to 24.5-inch diameter were used, and one of these was installed in a large anechoic test chamber for acoustic measurement of conditions simulating representative takeoffs, power cutbacks, and landing approaches. Attention is presently given to the data acquisition/reduction systems, the scaling criteria used to obtain engine size acoustic data, and comparisons with demonstrator aircraft in-flight acoustic test results.

Janardan, B. A.↗
NASA NTRS1984

Airborne Doppler lidar wind field measurements

A coherent Doppler lidar has been used in an aircraft to measure the two-dimensional wind field in a number of different atmospheric situations. The lidar, a pulsed CO2 system, was installed in the NASA Convair 990, Galileo II, and flown in a summer field program that included flights in California, in Oklahoma at the National Severe Storms Laboratory, and in Montana at the Cooperative Convective Precipitation Experiment (CCOPE). This paper provides a brief description of the instrumentation and summarizes the research flights. Examples of some of the results are given along with plans for future use of the lidar.

Bilbro, J.↗
NASA NTRS1982

Blowing Agents for Fabrication of Polyimide Foams

Polyimide resin can be foamed by agent generated within matrix of powder precursor. Blowing agent is mixture of water and methanol that are byproducts of condensation/polymerization reaction in resin. Expansion of these two compounds produces cellular foam structure that is flexible and resilient but that tends to have very-fine cellular structure. More open structure with lower density can be attained by modifying mechanism of foam formation. Foams have applications as fillers for seat cushions, wall panels, floor sheets, and thermal and acoustical insulation.

Gagliani, J.↗
NASA NTRS1981

Formulation and characterization of polyimide resilient foams of various densities for aircraft seating applications

Light weight, heat and fire resistant low smoke generating polyimide foams are developed for aircraft seating applications. The material is upgraded and classified into groups for fabrication of cushions possessing acceptable comfort properties. Refinement and selection of foaming processes using a variety of previously developd foaming techniques and definition of property relationships to arrive at the selection and classfication of polyimide foams into five groups in accordance with predetermined ILD values are emphasized.

Gagliani, J.↗
NASA NTRS1981

Modified fire-resistant foams forseat cushions

Modified polyimide-polymer resins are precursors for new family of resilient fire-resistant foams. Terpolyimide foams containing long-chain aliphatic diamines withstand 50,000 cycles of compression over a 200 pound load - an equivalent of 3 years of continuous use as seat cushion filler.

Gagliani, J.↗
NASA NTRS1981

One-step microwave foaming and curing

Process that combines microwave foaming and curing of polyimide precursors in single step produces fire-resistant foam slabs of much larger volume than has previously been possible. By adding selected conductive fillers to powder precursors and by using high-power microwave oven, foam slabs with dimensions in excess of 61 by 61 by 7.6 cm are made. Typical foaming and curing and curing time is 35 minutes in microwave oven with additional 1 to 2 hour postcure in conventional oven.

Gagliani, J.↗
NASA NTRS1981

Rigid fire-resistant foams for walls and floors

Previous techniques for fabricating rigid fire-resistant polyimide foams by compressing already-foamed precursor have been supplanted by one-step constrained-rise process. Precursor mixed with reinforcing fillers is placed between rigid substrates that constrain expansion of foam as it is heated by microwave energy. Process works for both liquid and powder precursors and can also be adapted to attach woven fiberglass skins at same time prcursor is being foamed.

Gagliani, J.↗
NASA NTRS1980

Report of convective phenomena team

A group meeting was assembled to focus on the planning of specific experiments, to establish some priorities, identify interested scientists who would like to participate, establish any special requirements, make recommendations on data processing, and to prepare flight plan outlines. Since the number of convective storms in the CCOPE (Cooperative Convective Precipitation Experiment) field experiment area are limited to only a few days during the operational time period the flight plans must be designed with a hierarchy of abort experiments so that the easily identified and lowest probability events should take priority until their quota is filled.

Orville, H.↗
NASA NTRS1980

Retinal changes in rats flown on Cosmos 936 - A cosmic ray experiment

Ten rats, five centrifuged during flight to simulate gravity and five stationary in flight and experiencing hypogravity, orbited the Earth. No differences were noted between flight-stationary and flight-centrifuged animals, but changes were seen between these two groups and ground controls. Morphological alterations were observed comparable to those in the experiment flown on Cosmos 782 and to the retinal cells exposed to high-energy particles at Berkeley. Affected cells in the outer nuclear layer showed swelling, clearing of cytoplasm, and disruption of the membranes. Tissue channels were again found, similar to those seen on 782. After space flight, preliminary data indicated an increase in cell size in montages of the nuclear layer of both groups of flight animals. This experiment shows that weightlessness and environmental conditions other than cosmic radiation do not contribute to the observed damage of retinal cells.

Philpott, D. E.↗
NASA NTRS1980

Development of fire-resistant, low smoke generating, thermally stable end items for commercial aircraft and spacecraft using a basic polyimide resin

A terpolyimide precursor was developed which can be foamed by microwave methods and yields foams possessing the best seating properties. A continuous process, based on spray drying techniques, permits production of polyimide powder precursors in large quantities. The constrained rise foaming process permits fabrication of rigid foam panels with improved mechanical properties and almost unlimited density characteristics. Polyimide foam core rigid panels were produced by this technique with woven fiberglass fabric bonded to each side of the panel in a one step microwave process. The fire resistance of polyimide foams was significantly improved by the addition of ceramic fibers to the powder precursors. Foams produced from these compositions are flexible, possess good acoustical attenuation and meet the minimum burnthrough requirements when impinged by high flux flame sources.

Gagliani, J.↗
NASA NTRS1978

Effects of Radiation on Rat Retina after 18 days of Space Flight

Although cumulative effects an retina from low-dose radiation during prolonged spaceflight are not known, ary impairment of vision could set limits for spaceflight duration. Cosmic rays are now considered to be the cause of the "light flashes" seen during spaceflight by activating retina cells as they pass through the photoreceptors. Previous studies have also shown retinal cellular alterations and cell necrosis from high-energy, particle (HZE) radiation. Ten rats, 5 centrifuged during flight (FC) to simulate gravity and 5 in-flight stationary (FS) experiencing hypogravity, orbited Earth for 18.5 days on Cosmos 936. The animals were sacrificed 25 days post-recovery and the eyes flown to Ames Res. Ctr. The pattern of cell necrosis in the retinas from the FC group showed the same response to radiation as the FS. This would indicate that hypogravity was not a factor in the observed results. Also the cellular response in the retinas exposed in the Berkeley accelerator again matched both the FC and FS eyes. Thus all three conditions provide comparable changes and indicate HZE particles as the possible cause of the cellular alterations, channels, and breakdown.

Philpott, D.↗
NASA NTRS1977

Independent Evaluation of Shuttle Flight Control System

A brief summary of the work performed on the Approach and Landing Test (ALT) shuttle flight control system is presented. (FCS) and a bibliography of the formal reports are included which document the activities in detail. In general, the activities were grouped in four categories: (1) independent evaluation of ALT FCS software design; (2) independent evaluation of Software Development Laboratory (SDL) testing of ALT FCS software; (3) independent evaluation of Shuttle Avionics Integration Laboratory (SAIL) ALT FCS testing; and (4) independent evaluation of ALT flight test results.

Lee, R.↗
NASA NTRS1976

Coannular plug nozzle noise reduction and impact of exhaust system designs

Reducing the noise generated by high velocity jets has confronted engine designers and acoustics workers alike for the past fifteen years. Some of the jet noise suppressor configurations that are investigated are shown. With the exception of the early CJ-805 daisy suppressor nozzle which found successful application on the Convair 990 airplane, the others were developmental hardware at different stages of the effort in the past eight years - all aiming at potential supersonic cruise aircraft applications. Some significant progress was made as the result of work supported by NASA and FAA in the past two to three years. This work pertains to the concept demonstration and scale model testing of coannular plug nozzles with inverted velocity profile, and to the preliminary study of its application to advanced variable cycle engines (VCE) appropriate for supersonic cruise aircraft.

Lee, R.↗
NASA NTRS1973

QCSEE task 2: Engine and installation preliminary design

High-bypass turbofan engines with features required for commercial short haul powered lift transports were designed. Two engines were configured for each of the externally blown flap installations, under-the-wing and over-the-wing. Estimates of installed and uninstalled performance, noise, and weight were defined for each propulsion system.

Neitzel, R. E.↗
NASA NTRS1972

TF-34 turbofan quiet engine study

A study of high bypass turbofan engines in heavily sound-suppressed nacelles based on the TF-34 engine. The four-engine noise objective was 95 PNdb at four locations typical of takeoff and landing. Three engines were studied; these had fan pressure ratios, bypass ratios, and fan tip speeds respectively of 1.48/6.5/404 m/sec (1327 ft/sec), 1.25/13/305 (1000), 1.25/13/366(1200). The bypass 13 engines had a variable pitch fan, direct- and gear-driven. Noise suppressive treatment was identified which met 95 PNdb objective except for sideline liftoff at 6.5 bypass, full power, which was 2 PNdb noisier; at 90% power, 95 PNdb was achieved.

Edkins, D. P.↗