Engineering topics

Lee, K. D.

Publications and source records attributed to Lee, K. D..

12 records

NASA NTRS1993

Design efficiency evaluation for transonic airfoil optimization - A case for Navier-Stokes design

A constrained-optimization design method which improves the aerodynamic performance of transonic airfoils is evaluated from a design-quality and design-efficiency viewpoint. Design efficiency is a measure of the performance improvement and the design time (CPU time). Total-airfoil design and upper-surface design are performed using the Euler and Navier-Stokes equations with several grids, and are evaluated using the Navier-Stokes equations to determine the anticipated physical design response. Even though the cost of the Euler design is lower than Navier-Stokes design, the Navier-Stokes evaluation indicates that the Euler design does not necessarily improve the aerodynamic performance. Therefore, the design optimization should be based on an accurate flow simulation to achieve an actual performance improvement, and the design time is a secondary concern.

Hager, J. O.↗

NASA NTRS1993

Three-dimensional Navier-Stokes calculations using solution-adapted grids

A three-dimensional solution-adaptive grid generation technique is presented. The adaptation technique redistributes grid points to improve the accuracy of a flow solution without increasing the number of grid points. It is applicable to structured grids with a multiblock topology. The method uses a numerical mapping and potential theory to modify the initial grid distribution based on the properties of the flow solution on the initial grid. The technique is demonstrated with two examples - a transonic finite wing and a supersonic blunt fin. The advantages are shown by comparing flow solutions on the adapted grids with those on the initial grids.

Henderson, T. L.↗

NASA NTRS1992

MAG3D and its application to internal flowfield analysis

MAG3D (multiblock adaptive grid, 3D) is a 3D solution-adaptive grid generation code which redistributes grid points to improve the accuracy of a flow solution without increasing the number of grid points. The code is applicable to structured grids with a multiblock topology. It is independent of the original grid generator and the flow solver. The code uses the coordinates of an initial grid and the flow solution interpolated onto the new grid. MAG3D uses a numerical mapping and potential theory to modify the grid distribution based on properties of the flow solution on the initial grid. The adaptation technique is discussed, and the capability of MAG3D is demonstrated with several internal flow examples. Advantages of using solution-adaptive grids are also shown by comparing flow solutions on adaptive grids with those on initial grids.

Lee, K. D.↗

NASA NTRS1991

Grid generation strategies for turbomachinery configurations

Turbomachinery flow fields involve unique grid generation issues due to their geometrical and physical characteristics. Several strategic approaches are discussed to generate quality grids. The grid quality is further enhanced through blending and adapting. Grid blending smooths the grids locally through averaging and diffusion operators. Grid adaptation redistributes the grid points based on a grid quality assessment. These methods are demonstrated with several examples.

Lee, K. D.↗

NASA NTRS1991

Grid quality improvement by a grid adaptation technique

A grid adaptation technique is presented which improves grid quality. The method begins with an assessment of grid quality by defining an appropriate grid quality measure. Then, undesirable grid properties are eliminated by a grid-quality-adaptive grid generation procedure. The same concept has been used for geometry-adaptive and solution-adaptive grid generation. The difference lies in the definition of the grid control sources; here, they are extracted from the distribution of a particular grid property. Several examples are presented to demonstrate the versatility and effectiveness of the method.

Lee, K. D.↗

NASA NTRS1989

An improvement of convection fidelity in Euler calculations

A new solution procedure is presented to solve the Euler equations for steady, compressible, rotational, inviscid flows. The approach is aimed at achieving real inviscid solutions in Euler calculations by eliminating numerical diffusion. The variables in the Euler equations are divided into elliptic and convective quantities, using the Clebsch velocity decomposition. The convective quantities are then transported without numerical contamination using an efficient convection operator, while the elliptic quantities are integrated with a relaxation procedure. This approach provides a generalization of the full potential formulation to rotation Euler physics by allowing variations of convective quantities. Results are demonstrated for several transonic flows in two dimensions.

Lee, K. D.↗

NASA NTRS1983

User's guide for the Solar Backscattered Ultraviolet (SBUV) and the Total Ozone Mapping Spectrometer (TOMS) RUT-S and RUT-T data sets: October 31, 1978 to November 1, 1980

Raw data from the Solar Backscattered Ultrviolet/Total Ozone Mapping Spectrometer (SBUV/TOMS) Nimbus 7 operation are available on computer tape. These data are contained on two separate sets of RUTs (Raw Units Tapes) for SBUV and TOMS, labelled RUT-S and RUT-T respectively. The RUT-S and RUT-T tapes contain uncalibrated radiance and irradiance data, housekeeping data, wavelength and electronic calibration data, instrument field-of-view location and solar ephemeris information. These tapes also contain colocated cloud, terrain pressure and snow/ice thickness data, each derived from an independent source. The "RUT User's Guide" describes the SBUV and TOMS experiments, the instrument calibration and performance, operating schedules, and data coverage, and provides an assessment of RUT-S and -T data quality. It also provides detailed information on the data available on the computer tapes.

Fleig, A. J.↗

NASA NTRS1982

Ozone climatology series. Volume 1: Atlas of total ozone, April 1970 - December 1976

Contours and gridded values are given for seven years of monthly mean total ozone data derived from observations with the Backscattered Ultraviolet instrument on Nimbus-4 for the Northern and Southern Hemispheres. The instrument, algorithm, uncertainties in derived ozone and systematic changes in the bias with respect to the international groundbased ozone network of Dobson instruments, are discussed.

Heath, D. F.↗

NASA NTRS1981

BGRID: A block-structured grid generation code for wing sections

The operation of the BGRID computer program is described for generating block-structured grids. Examples are provided to illustrate the code input and output. The application of a fully implicit AF (approximation factorization)-based computer code, called TWINGB (Transonic WING), for solving the 3D transonic full potential equation in conservation form on block-structured grids is also discussed.

Chen, H. C.↗

NASA NTRS1981

Vertical ozone profile results from the Nimbus-4 BUV data

A seven year data set which consists of both total ozone and ozone vertical profiles has been derived from the Nimbus-4 Backscatter Ultraviolet (BUV) experiment. The BUV experiment measures the earth's backscattered solar radiance at 12 wavelengths in the Hartley-Huggins band. The shortest 8 bands are used to determine the vertical ozone profile. The longest four bands are used to determine the total ozone. The present investigation provides a review of the major characteristics of the instrument performance and ozone results during the seven year period of the data set. Attention is given to the data coverage in time and space, the major areas of nonhomogeneous coverage, adjustments made to the basic instrument radiances, long-term trends in the radiances, rocket and balloon measurements, and problems associated with the validation of the satellite data set.

Fleig, A. J.↗

NASA NTRS1980

Grid generation for general three-dimensional configurations

A suitable grid system for complex three dimensional configurations such as wing/body/nacelle shape for the solution of nonlinear transonic flow problems was constructed. Two approaches were explored based on Thompson's body fitted coordinate concept. The most general approach was to divide the computational domain into multiple rectangular blocks where the configuration itself was also represented by a set of blocks whose structure follows the natural lines of the configuration. The block structured grid system was adaptable to complex configurations and gives good grid quality near physical corners. However, it introduced algorithm issues for the flow solution concerning the treatment of nonanalytic grid block boundaries and nonstandard grid cells. These issues were explored in relation to the grid generation. A more limited approach treats a wing/body configuration with only a single rectangular block in computational space. The issues involving nonstandard cells were avoided, but other limitations on grid resolution appear. Both a linear and a nonlinear system of grid generation equations were developed including methods of grid control.

Lee, K. D.↗

NASA NTRS1980

Effect of grid system on finite element calculation

Detailed parametric studies of the effect of grid system on finite element calculation for potential flows were made. These studies led to the formulation of a design criteria for optimum mesh system and the development of two methods to generate the optimum mesh system. The guidelines for optimum mesh system are: (1) the mesh structure should be regular; (2) the element should be as regular and equilateral as possible; (3) the distribution of size of element should be consistent with that of flow variables to insure maximum uniformity in error distribution; (4) for non-Dirichlet boundary conditions, smaller boundary elements or higher order interpolation functions should be used; and (5) the mesh should accommodate the boundary geometry as accurately as possible. The results of the parametric studies are presented.

Lee, K. D.↗