Engineering topics
Lee, J Y
Publications and source records attributed to Lee, J Y.
XAFS characterization of mercury captured on cupric chloride-impregnated sorbents.
Abstract not provided
Framework for Interoperable Sustainable Manufacturing Process Analysis Applications Development
Abstract not provided
Dominant front-side acceleration of energetic proton beams from plastic targets irradiated by an ultraintense laser pulse
An experimental observation has been made by using aluminum-coated Mylar foils, which strongly supports that in the case of plastic target, the energetic part of the proton beam originates from the front-side of the target. When a 30 fs laser pulse with an intensity of 1.6x10{sup 19} W/cm{sup 2} was irradiated on the 12.5-{mu}m-thick Mylar side of the aluminum-coated Mylar foil, the maximum proton energy was reduced by a factor 5.5 as compared to that of 3.3 MeV observed from the single layer of the Mylar foil. With the help of a two-dimensional particle-in-cell simulation, these observations can be interpreted that in the case of plastic target, the energetic proton beam originates from the front-side of the target. In the case of an aluminum-coated 6-{mu}m-thick Mylar foil, more energetic proton beams of 4.7 MeV were also observed when the laser pulse was irradiated on the aluminum side as compared to those of 3.4 MeV from the single Mylar foil.
Formation mechanisms of metallic Zn nanodots by using ZnO thin films deposited on n-Si substrates
High-resolution transmission electron microscopy and energy dispersive x-ray spectroscopy results showed that metallic Zn nanodots (NDs) were fabricated through transformation of ZnO thin films by deposition of SiO{sub x} on ZnO/n-Si (100) heterostructures. The Zn NDs with various sizes and densities were formed due to the occurrence of the mass diffusion of atoms along the grain boundaries in the ZnO thin films. The fabrication mechanisms of metallic Zn NDs through transformation of ZnO thin films deposited on n-Si substrates are described on the basis of the experimental results.
Magnetism of one-dimensional strongly repulsive spin-1 bosons with antiferromagnetic spin-exchange interaction
We investigate magnetism and quantum phase transitions in a one-dimensional system of integrable spin-1 bosons with strongly repulsive density-density interaction and antiferromagnetic spin-exchange interaction via the thermodynamic Bethe ansatz method. At zero temperature, the system exhibits three quantum phases: (i) a singlet phase of boson pairs when the external magnetic field H is less than the lower critical field H{sub c1}; (ii) a ferromagnetic phase of atoms in the hyperfine state |F=1, m{sub F}=1> when the external magnetic field exceeds the upper critical field H{sub c2}; and (iii) a mixed phase of singlet pairs and unpaired atoms in the intermediate region H{sub c1}<H<H{sub c2}. At finite temperatures, the spin fluctuations affect the thermodynamics of the model through coupling the spin bound states to the dressed energy for the unpaired m{sub F}=1 bosons. However, such spin dynamics is suppressed by a sufficiently strong external field at low temperatures. Thus the singlet pairs and unpaired bosons may form a two-component Luttinger liquid in the strong coupling regime.
Modeling of mercury oxidation and adsorption by cupric chloride-impregnated carbon sorbents
Cupric chloride-impregnated activated carbon sorbents (CuCl{sub 2}-ACs) showed good performance in Hg{sup 0} oxidation and adsorption in previously published entrained-flow test results. In addition, our previous studies indicated that Hg{sup 0} is oxidized by CuCl{sub 2}-ACs and the resultant oxidized mercury is readsorbed onto the sorbents. This study conducted mathematical modeling to interpret. these previous results and better understand the Hg{sup 0} oxidation and adsorption mechanism of CuCl{sub 2}-ACs. As a result the mathematical modeling results confirmed that Hg{sup 0} oxidation by CuCl{sub 2}-ACs is determined by the injection level of CuCl{sub 2} impregnated onto the sorbents. An increase in Cu Cl{sub 2} loading in CuCl{sub 2}-ACs was found to increase Hg{sup 0} oxidation but very slightly increased Hg adsorption because an increase in Cu Cl{sub 2} loading decreased the active CuCl{sub 2}-free carbon sites available for the readsorption of resultant oxidized mercury on the surfaces and inside the pores.
Investigation of a mercury speciation technique for flue gas desulfurization materials
Most of the synthetic gypsum generated from wet flue gas desulfurization (FGD) scrubbers is currently being used for wallboard production. Because oxidized mercury is readily captured by the wet FGD scrubber, and coal-fired power plants equipped with wet scrubbers desire to benefit from the partial mercury control that these systems provide, some mercury is likely to be bound in with the FGD gypsum and wallboard. In this study, the feasibility of identifying mercury species in the FGD gypsum and wallboard samples was investigated using a large sample size thermal desorption method and samples from power plants in Pennsylvania. Potential candidates of pure mercury standards including mercuric chloride, mercurous chloride, mercury oxide, mercury sulfide, and mercuric sulfate were analyzed to compare their results with those obtained from FGD gypsum and dry wallboard samples. Although any of the thermal evolutionary curves obtained from these pure mercury standards did not exactly match with those of the FGD gypsum and wallboard samples, it was identified that Hg{sub 2}Cl{sub 2} and HgCl{sub 2} could be candidates. An additional chlorine analysis from the gypsum and wallboard samples indicated that the chlorine concentrations were approximately 2 orders of magnitude higher than the mercury concentrations, suggesting possible chlorine association with mercury. 21 refs., 5 figs., 3 tabs.
Different effects of a laser prepulse on the proton generation between plastic and metal targets irradiated by an ultraintense laser pulse
The effect of a laser prepulse on the generation of proton beams is compared between plastic and metal targets by irradiating a 30 fs, 2.4x10{sup 18} W/cm{sup 2} Ti:sapphire laser pulse. Proton energies generated from both target materials increase as the pulse duration of the laser prepulse decreases. However, it was found that there are distinct differences with respect to target materials. In the case of aluminum targets, as target thickness decreases, proton energy gets higher, which is well described by an isothermal expansion model. However, in the case of Mylar targets, no such dependence on target thickness could be observed, and the highest maximum proton energies are higher by factors of 1.5 to 3 than those from aluminum targets or those predicted by the isothermal expansion model. Such characteristics of the proton beams from Mylar targets can be accounted for by a bulk acceleration model, or acceleration by a resistively induced electric field.
Transformation mechanisms from metallic Zn nanocrystals to insulating ZnSiO{sub 3} nanocrystals in a SiO{sub 2} matrix due to thermal treatment
Transmission electron microscopy (TEM), high-resolution TEM, and x-ray energy dispersive spectroscopy results showed that Zn metallic nanocrystals and ZnSiO{sub 3} insulating nanocrytals embedded in a SiO{sub 2} matrix were created from the ZnO thin films deposited on n-Si (001) substrates due to rapid thermal annealing. The formed Zn metallic nanocrystals were transformed into monoclinic ZnSiO{sub 3} insulating nanocrystals with increasing number of Zn atoms resulting from an increase in the annealing time up to 10 min. The transformation mechanisms from metallic Zn nanocrystals to insulating ZnSiO{sub 3} nanocrystals in a SiO{sub 2} matrix due to rapid thermal annealing are described on the basis of the experimental results.