Nanosecond laser-induced damage of transparent conducting ITO film at 1064 nm
Abstract not provided
Engineering topics
Publications and source records attributed to Lee, J I.
Abstract not provided
Abstract not provided
Abstract not provided
Abstract not provided
We fabricated low-density GaAs/AlGaAs quantum dots for single photon source by droplet epitaxy. We investigated the emission energies of the dots and underlying superlattice by using photoluminescence and cathodoluminescence measurements. By forming a mesa etched structure, we distinguished the transitions from the superlattice and the dots. And we calculated the diffusion length in this system from the peak shift of the superlattice, and applied the diffusion to the dots to investigate the emission energy shift of the QDs.z
GaAs quantum dot (QD) was grown by droplet epitaxy (DE) method and the excitation power dependence of photoluminescence (PL) were carried out. To investigate the effect of annealing temperature on QDs optical properties, the two step RTA process was carried out in a various temperature range from 800 to 1000 deg. C. As the thermal annealing temperature increases, the PL peak position is blue-shifted due to the change of the composition and size distribution of QDs, and the highest PL intensity is observed at the sample annealed at 900 deg. C. The integrated PL intensity (I{sub PL}) is plotted against the excitation density in a log-log scale and the slope was calculated.
The GaAs quantum dots in AlGaAs barriers were grown by droplet epitaxy, emitting around 700 nm in wavelength which is compatible with low cost Si based detectors. The excitation power dependent and time resolved micro-photoluminescence measurements identified optical characteristics of exciton and biexciton states which are attributed to good quantum confinements in GaAs QDs.
Complex target structures are necessary to take full advantage of the unique laboratory environment created by inertial confinement fusion experiments. For example, uses-of-ignition targets that contain a thin layer of a low density nanoporous material inside a spherical ablator shell allow placing dopants in direct contact with the DT fuel. The ideal foam for this application is a low-density hydrocarbon foam that is strong enough to survive wetting with cryogenic hydrogen, and low enough in density (density less than {approx}30 mg/cc) to not reduce the yield of the target. Here, we discuss the fabrication foam-lined uses-of-ignition targets, and the development of low-density foams that can be used for this application. Much effort has been directed over the last 20 years toward the development of spherical foam targets for direct-drive and fast-ignition experiments. In these targets, the spherical foam shell is used to define the shape of the cryogenic DT fuel layer, or acts as a surrogate to simulate the cryogenic fuel layer. These targets are fabricated from relatively high-density aerogels (>100 mg/cc) and coated with a few micron thick permeation barrier. With exception of the above mentioned fast ignition targets, the wall of these targets is typically larger than 100 microns. In contrast, the fusion application targets for indirect-drive experiments on NIF will require a much thinner foam shell surrounded by a much thicker ablator shell. The design requirements for both types of targets are compared in Table 1. The foam shell targets for direct-drive experiments can be made in large quantities and with reasonably high yields using an encapsulation technique pioneered by Takagi et al. in the early 90's. In this approach, targets are made by first generating unsupported foam shells using a triple-orifice droplet generator, followed by coating the dried foam shells with a thin permeation barrier. However, this approach is difficult, if not impossible, to transfer to the lower density and thinner wall foam shells required for indirect-drive uses-of-ignition targets for NIF that then would have to be coated with an at least hundred-micron-thick ablator film. So far, the thinnest shells that have been fabricated using the triple-orifice-droplet generator technique had a wall thickness of {approx}20 microns, but despite of being made from a higher-density foam formulation, the shells were mechanically very sensitive, difficult to dry, and showed large deviations from roundness. We thus decided to explore a different approach based on using prefabricated thick-walled spherical ablator shells as templates for the thin-walled foam shell. As in the case of the above mentioned encapsulation technique, the foam is made by sol-gel chemistry. However, our approach removes much the requirements on the mechanical stability of the foam shell as the foam shell is never handled in its free-standing form, and promises superior ablator uniformity and surface roughness. As discussed below, the success of this approach depends strongly on the availability of suitable aerogel chemistries (ideally pure hydrocarbon (CH)-based systems) with suitable rheological properties (high viscosity and high modulus near the gel point) that produce low-density and mechanically strong foams.
This paper outlines the characterization of voids and Microstructure in TATB-based Explosives over several orders of magnitude, from sizes on the order of 10 nm to about 1 cm. This is accomplished using ultra small angle x-ray scattering to investigate voids from a few nm to a few microns, ultra small angle neutron scattering for voids from 100 nm to 10 microns, and x-ray computed microtomography to investigate microstructure from a few microns to a few centimeters. The void distributions of LX-17 are outlined, and the microstructure of LX-17 is presented. Temperature cycling and compressive creep cause drastically different damage to the microstructure. Temperature cycling leads to a volume expansion (ratchet growth) in TATB-based explosives, and x-ray scattering techniques that are sensitive to sizes up to a few microns indicated changes to the void volume distribution that had previously accounted for most, but not all of the change in density. This paper presents the microstructural damage larger than a few microns caused by ratchet growth. Temperature cycling leads to void creation in the binder poor regions associated with the interior portion of formulated prills. Conversely, compressive creep causes characteristically different changes to microstructure; fissures form at binder-rich prill boundaries prior to mechanical failure.
The work conducted in this project was conducted with the aim of identifying and understanding the origin and mechanisms of magnetic behavior in undoped semiconductor nanocrystals (NCs), specifically those composed of CdSe. It was anticipated that the successful completion of this task would have the effect of addressing and resolving significant controversy over this topic in the literature. Meanwhile, application of the resultant knowledge was expected to permit manipulation of the magnetic properties, particularly the strength of any magnetic effects, which is of potential relevance in a range of advanced technologies. More specifically, the project was designed and research conducted with the goal of addressing the following series of questions: (1) How does the magnitude of the magnetism in CdSe NCs change with the organic molecules used to passivate their surface the NC size? i.e. Is the magnetism an intrinsic effect in the nanocrystalline CdSe (as observed for Au NCs) or a surface termination driven effect? (2) What is the chemical (elemental) nature of the magnetism? i.e. Are the magnetic effects associated with the Cd atoms or the Se atoms or both? (3) What is/are the underlying mechanism(s)? (4) How can the magnetism be controlled for further applications? To achieve this goal, several experimental/technical milestones were identified to be fulfilled during the course of the research: (A) The preparation of well characterized CdSe NCs with varying surface termination (B) Establishing the extent of the magnetism of these NCs using magnetometry (particularly using superconducting interference device [SQUID]) (C) Establishing the chemical nature of the magnetism using x-ray magnetic circular dichroism (XMCD) - the element specific nature of the technique allows identification of the element responsible for the magnetism (D) Identification of the effect of surface termination on the empty densities of states (DOS) using x-ray absorption spectroscopy (XAS), with particular emphasis on elucidating small changes in the d-electron count. Characterizing changes in the d-electron density can yield important insight into the mechanisms of magnetism in materials. As the three attached manuscripts illustrate (presented in preprint form to ensure no infringement of copyright), each of these milestones was successfully illustrated and the results published in the scientific literature during the course of the project. The research team members were able to determine, from a series of XAS, XMCD and SQUID magnetometry measurements, that CdSe NCs are paramagnetic and that the magnitude of magnetic susceptibility is dependent upon the type of organic molecule used to passivate the NC surface (i.e. the observed magnetism results, at least in part, from a surface effect that is not intrinsic to the NCs). In addition, they identified that the mechanism by which the magnetic susceptibility is modified - via {pi} back-donation of d-electrons to the organic ligands from the Cd atoms. These findings demonstrate that the magnetic properties are related to the surface Cd atoms and illustrate the means by which the magnetic behavior can be manipulated for specific technological applications. Two of the papers published during the course of the LW project do not contain magnetometry data, but focus on the evolution in electronic structure of the CdSe NCs as a function of particle size. These measurements were crucial in developing an understanding of the electronic behavior of the NCs and, ultimately, in assigning the p back-donation mechanism for inducing controllable paramagnetic behavior. Significantly, the research team has also filed a patent application based upon their research: 'Method for Creating Ligand Induced Paramagnetism in Nanocrystalline Structures' Docket: IL-11858. It is noted that both LDRD-LW and Office of Basic Energy Sciences (OBES) funding is acknowledged in the attached manuscripts. As such, is important to indicate that funds were not comingled during the course of the project. Some of the experimental data presented in the manuscripts was collected prior to the LDRD-LW award by Dr. Meulenberg and Dr. Lee, who were supported by an OBES award at the time. This data was, in part, used by Dr. Meulenberg in his proposal/presentation for the LDRD-LW competition. Moreover, the vast majority of data presented in the three papers was collected at OBES-funded synchrotron facilities which necessitated an acknowledgement to OBES.
The study of nanometer sized semiconductor crystallites, also known as quantum dots (QDs), has seen rapid advancements in recent years in scientific disciplines ranging from chemistry, physics, biology, materials science, and engineering. QD materials of CdSe, ZnSe, InP, as well as many others, can be prepared in the size range of 1-10 nm producing uniform, nearly monodisperse materials that are typically coated with organic molecules [1-3]. The strength of charge carrier confinement, which dictates the size-dependent properties, in these QDs depends on the nature of the material and can be correlated to the Bohr radius for the system of interest. For instance, the Bohr radius for CdSe is {approx} 5 nm, while in the more covalent structure of InP, the Bohr radius approaches {approx} 10 nm. The study of CdSe QDs has been particularly extensive during the last decade because they exhibit unique and tunable optical properties and are readily synthesized with high-crystallinity and narrow size dispersions. Although the core electronic properties of CdSe are explained in terms of the quantum confinement model, experimental efforts to elucidate the surface structure of these materials have been limited. Typically, colloidal CdSe QDs are coated with an organic surfactant, which typically consists of an organo-phosphine, -thiol, or -amine, that has the function of energetically relaxing defect states via coordination to partially coordinated surface atoms. The organic surfactant also acts to enhance carrier confinement and prevent agglomeration of the particles. Chemically, it has been shown that the bonding of the surfactant to the CdSe QD occurs through Cd atoms resulting cleavage of the Se atoms and formation of a Cd-rich (i.e. non-stoichiometric) particle [5].
KIMS is a dark matter search experiment using low background CsI(TB) crystals at Yangyang Underground Laboratory in Korea. With a total exposure of 3409 kg{center_dot}d data, we set a new limit on WIMP-nucleon cross section. We achieved the most stringent limit on the spin-dependent interaction for a pure proton case. We were able to exclude the DAMA signal region for both spin-dependent and spin-independent interaction for the WIMP mass greater than 20 GeV/c{sup 2}. KIMS experiment is upgraded with 12 CsI(TB) crystals corresponding to a total mass of 104 kg and accumulating data since Jan. 2008.