Engineering Papers⌕ Search

Engineering topics

Law, Jack D.

Publications and source records attributed to Law, Jack D..

At least 19 records

Countercurrent Actinide Lanthanide Separation Process (ALSEP) Demonstration Test with a Simulated PUREX Raffinate in Centrifugal Contactors on the Laboratory Scale

An Actinide Lanthanide Separation Process (ALSEP) for the separation of trivalent actinides (An(III)) from simulated raffinate solution was successfully demonstrated using a 32-stage 1 cm annular centrifugal contactor setup. The ALSEP solvent was composed of a mixture of 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (HEH[EHP]) and N,N,N',N'-tetra-(2-ethylhexyl)-diglycolamide (T2EHDGA) in n-dodecane. Flowsheet calculations and evaluation of the results were done using the Argonne’s Model for Universal Solvent Extraction (AMUSE) code using single-stage distribution data. The co-extraction of Zr(IV) and Pd(II) was prevented using CDTA (trans-1,2-diaminocyclohexane-N,N,N',N'-tetraacetic acid) as a masking agent in the feed. For the scrubbing of co-extracted Mo; citrate-buffered acetohydroxamic acid was used. The separation of An(III) from the trivalent lanthanides (Ln(III)) was achieved using citrate-buffered diethylene-triamine-N,N,N',N",N"-pentaacetic acid (DTPA), and Ln(III) were efficiently back extracted using N,N,N',N'-tetraethyl-diglycolamide (TEDGA). A clean An(III) product was obtained with a recovery of 95% americium and curium. The Ln(III) were efficiently stripped; but the Ln(III) product contained 5% of the co-stripped An(III). The carryover of Am and Cm into the Ln(III) product is attributed to too few actinide stripping stages, which was constrained by the number of centrifugal contactors available. Improved separation would be achieved by increasing the number of An strip stages. The heavier lanthanides (Pr, Nd, Sm, Eu, and Gd) and yttrium were mainly routed to the Ln product, whereas the lighter lanthanides (La and Ce) were mostly routed to the raffinate.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Adsorbents and adsorption models for capture of Kr and Xe gas mixtures in fixed-bed columns

Off-gases produced during the reprocessing of used nuclear fuel (UNF) include 129-I 2 , 3-HHO, 14-CO 2 , 85-Kr, and 135-Xe, which are volatilized out into the off-gas. In order to meet regulatory requirements for reprocessing plant emissions, these gases must be captured and removed from the o?-gas stream prior to o?-gas emission. Of particular interest are the noble gases, Kr and Xe, which can be fairly difficult to remove from the off-gas due to their low chemical reactivity. Thus, this work is focused on utilizing engineered adsorbents, AgZ-PAN and HZ-PAN, to capture Kr and Xe from a mixed-gas stream at relatively low temperatures (191–295 K) and various flow rates (50–2000 mL/min). Isothermal data for Kr and Xe on each adsorbent are analyzed to produce the Langmuir parameters needed to model the mixture adsorption capacities at relevant temperatures using the Extended Langmuir model. Those parameters are then incorporated into a fixed-bed adsorption model developed in this work using the Mulitphysics Object-Oriented Simulation Environment (MOOSE). That model is used to simulate breakthrough times for Kr and Xe in packed columns of AgZ-PAN and HZ-PAN, ranging in length from 6 to 20 in., at relevant temperatures and flow rates. Breakthrough times varied from nearly instantaneous for Kr in AgZ-PAN to 30 h for Xe in HZ-PAN. After the developed model was validated by comparisons with experimental break-through data, the model framework was used to simulate the performance of multiple fixed-bed columns connected in series.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Aqueous Reprocessing of Used Nuclear Fuel

Aqueous reprocessing of used nuclear fuel has a long history of successful operation worldwide. The history of aqueous reprocessing and a description of current and past operating aqueous reprocessing facilities are provided and the main types of solvent extraction equipment utilized in the nuclear industry are described. While the PUREX process is well established for separating U and Pu from used nuclear fuel, numerous variants to the PUREX process are being developed and are described. Finally, advanced separation processes in which minor actinides are separated from the used nuclear fuel are a key research focus worldwide. These processes and the current state of development are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Oxidation and extraction of Am(VI) using a monoamidic extractant in 3D printed centrifugal contactors

In this study, a series of tests were performed using centrifugal contactors to evaluate the separation of Am(VI) from cerium, as well as to determine the efficiency of the contactors. All experiments were performed using 2-cm, acrylic 3D-printed centrifugal contactors. Solvent extraction tests were performed using 1 M N,N-di(2-ethylhexyl)butyramide (DEHBA)/dodecane and a nitric acid feed solution spiked with 243 Am and 139 Ce and oxidized with 60 mg mL -1 sodium bismuthate. Approximately 72 % of the Am was extracted with a single contactor stage. Co-stripping of Am and Ce was demonstrated but attempts at selective stripping were not successful. Lastly, successful recycle of the used organic phase was demonstrated. Contactor efficiencies of 95-100% were obtained.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An Advanced TALSPEAK Concept for Separating Minor Actinides. Part 1. Process Optimization and Flowsheet Development

A system is being developed to separate trivalent actinides from lanthanide fission product elements that uses 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester to extract the lanthanide ions into an organic phase, while the actinide ions are held in the citrate-buffered aqueous phase by complexation to N-(2-hydroxyethyl)ethylenediamine-N,N',N'-triacetic acid (HEDTA). Earlier investigations of this system using a 2-cm centrifugal contactor revealed that the relatively slow extraction of Sm3+, Eu3+, and Gd3+ resulted in low separation factors from Am3+. In the work reported here, adjustments to the aqueous phase chemistry were made to improve the extraction rates. The results suggest that increasing the concentration of the citric acid buffer from 0.2 to 0.6 mol/L, and lowering the pH from 3.1 to 2.6, significantly improved lanthanide extraction rates resulting in an actinide/lanthanide separation system suitable for deployment in centrifugal contactors. Experiments performed to evaluate whether the lanthanide extraction rates can be improved by replacing aqueous HEDTA with nitrilotriacetic acid (NTA) exhibited promising results. However, NTA exhibited an unsatisfactorily high distribution value for Am3+ under the extraction conditions examined.

actinide extraction↗

An Advanced TALSPEAK Concept for Separating Minor Actinides. Part 2. Flowsheet Test with Actinide-spiked Simulant

A solvent extraction system has been developed for separating trivalent actinides from lanthanides. This “Advanced TALSPEAK” system uses 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester to extract the lanthanides into a n-dodecane-based solvent phase, while the actinides are retained in a citrate-buffered aqueous phase by complexation to N-(2-hydroxyethyl)ethylenediamine-N,N',N'-triacetic acid. Batch distribution measurements indicate that the separation of americium from the light lanthanides decreases as the pH decreases. For example, the separation factor between La and Am increases from 2.5 at pH 2.0 to 19.3 at pH 3.0. However, previous investigations indicated that the extraction rates for the heavier lanthanides decrease with increasing pH. So, a balance between these two competing effects is required. An aqueous phase in which the pH was set at 2.6 was chosen for further process development because this offered optimal separation, with a minimum separation factor of ~8.4, based on the separation between La and Am. Centrifugal contactor single-stage efficiencies were measured to characterize the performance of the system under flow conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development and evaluation of a silver mordenite composite sorbent for the partitioning of xenon from krypton in gas compositions

A new engineered form composite sorbent for the selective separation of xenon from krypton in simulant composition off-gas streams resulting from the reprocessing of used nuclear fuel has been developed and evaluated. A sodium mordenite powder was incorporated into a macroporous polymer binder, formed into spherical beads and successfully converted to a 9 wt.% silver form composite sorbent. The final engineered form sorbent retained the characteristic surface area indicative of sodium mordenite powder. The sorbent was evaluated for xenon adsorption potential with capacities measured as high as 30 millimoles of xenon per kilogram of sorbent achieved at ambient temperature and 460 millimoles of xenon per kilogram sorbent at 220 K. Xenon/krypton selectivity was calculated to be 22.4 with a 1020 µL/L xenon, 150 µL/L krypton in a balance of air feed gas at 220 K. Furthermore, adsorption/desorption thermal cycling effects were evaluated with results indicating sorbent performance was not significantly impacted while undergoing numerous adsorption/desorption thermal cycles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Higher Americium Oxidation State Research Roadmap

The partitioning of hexavalent Am from dissolved nuclear fuel requires the ability to efficiently oxidize Am(III) to Am(VI) and to maintain that oxidation state for a length of time sufficient to perform the separation. Several oxidants have been, or are being developed. Chemical oxidants include Ag-catalyzed ozone, Ag-catalyzed peroxydisulfate, Cu(III) periodate, and sodium bismuthate. Hexavalent americium has also now successfully been prepared by electrolysis, using functionalized electrodes. So-called auto-reduction rates of Am(VI) are sufficiently slow to allow for separations. However, for separations based on solvent extraction or ion exchange using organic resins, the high valence state must be maintained under the reducing conditions of the organic phase contact, and a holding oxidant is probably necessary. Until now, only Cu(III) periodate and sodium bismuthate oxidation have been successfully combined with solvent extraction separations. Bismuthate oxidation provided the higher DAm, since it acts as its own holding oxidant, and a successful hot test using centrifugal contactors was performed. For the other oxidants, Ag-catalyzed peroxydisulfate will not oxidize americium in nitric acid concentrations above 0.3 M, and it is not being further investigated. Peroxydisulfate in the absence of Ag catalysis is being used to prepare Am(V) in ion exchange work, discussed below. Preliminary work with Ag-catalyzed ozone has been unsuccessful for extractions of Am(VI) from 6.5 M HNO3, and only one attempt at extraction, also from 6.5 M HNO3, using the electrolytic oxidation has been attempted. However, this high acid concentration was based on the highest Am extraction efficiency using the bismuthate oxidant; which is only sparingly soluble, and thus the oxidation yield is based on bismuthate solubility. Lower acid concentrations may be sufficient with alternative oxidants and work with Ag-ozone, Cu(III) and electrolysis is on-going. Two non-solvent-extraction separations are also under investigation. The first would separate Am(VI) by co-crystallization with uranium and the other oxidizable actinides as their nitrate salts. This novel idea has been successful in lab scale testing, and merits further investigation. Similarly, success has been achieved in separations using inorganic or hybrid ion exchange materials to sorb the lanthanides and actinides, while allowing pentavalent americium to elute. This is the only technique currently investigating Am(V), despite the advantages of this oxidation state with regard to its higher stability. The ultimate destination for this roadmap is to develop an americium separation that can be applied under process conditions, preferably affording a co-separation of the actinyl (VI) ions. Toward that end, emphasis is given here to selection of a solvent extraction flowsheet for testing in the INL centrifugal contactor hot test bed during FY16. A solvent extraction process will be tested mainly because solvent extraction separations of Am(VI) are relatively mature and the test bed currently exists in a configuration to support them. Thus, a major goal of FY16 is to select the oxidant/ligand combination to run such a test using the contactors. The only ligands under consideration are DAAP and DEHBA. This is not to say that ion exchange and co-crystallization techniques are unimportant. They merit continued investigation, but are not mature enough for hot test bed testing at this time.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multi-component testing using HZ-PAN and AgZ-PAN Sorbents for OSPREY Model validation

In efforts to further develop the capability of the Off-gas SeParation and RecoverY (OSPREY) model, multi-component tests were completed using both HZ-PAN and AgZ-PAN sorbents. The primary purpose of this effort was to obtain multi-component xenon and krypton capacities for comparison to future OSPREY predicted multi-component capacities using previously acquired Langmuir equilibrium parameters determined from single component isotherms. Experimental capacities were determined for each sorbent using two feed gas compositions of 1000 ppmv xenon and 150 ppmv krypton in either a helium or air balance. Test temperatures were consistently held at 220 K and the gas flowrate was 50 sccm. Capacities were calculated from breakthrough curves using TableCurve® 2D software by Jandel Scientific. The HZ-PAN sorbent was tested in the custom designed cryostat while the AgZ-PAN was tested in a newly installed cooling apparatus. Previous modeling validation efforts indicated the OSPREY model can be used to effectively predict single component xenon and krypton capacities for both engineered form sorbents. Results indicated good agreement with the experimental and predicted capacity values for both krypton and xenon on the sorbents. Overall, the model predicted slightly elevated capacities for both gases which can be partially attributed to the estimation of the parameters and the uncertainty associated with the experimental measurements. Currently, OSPREY is configured such that one species adsorbs and one does not (i.e. krypton in helium). Modification of OSPREY code is currently being performed to incorporate multiple adsorbing species and non-ideal interactions of gas phase species with the sorbent and adsorbed phases. Once these modifications are complete, the sorbent capacities determined in the present work will be used to validate OSPREY multicomponent adsorption predictions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The solvent extraction of Am(VI) using centrifugal contactors

One of the major challenges in nuclear fuel cycle research is the development of a separation that can be deployed on a process scale for americium from the lanthanides. Unlike most lanthanides, americium can be oxidized to higher oxidation states, and this presents an opportunity to exploit high valent americium for such a separation. Strong oxidizing agents are required. However, the preparation of hexavalent americium using sodium bismuthate has now become routine in our laboratory. The success of separations based on oxidized americium depends on not only the yield of the higher oxidation state, but also its persistence in solution. In batch contact work, short contact times allowed for the extraction of Am(VI) with DAm ~ 4, using 1 M diamylamylphosphonate as the ligand. Based on bench-scale extraction and stripping studies a flowsheet was designed and a hot test was performed in a radiological fume hood using three CINC, 5-cm centrifugal contactors. Stage 1 was the americium extraction stage. In stage 2, americium stripping was attempted after reduction with a low concentration of hydrogen peroxide. As the only lanthanide that oxidizies and extracts in this flowsheet, it was attempted to reduce and strip cerium in the third stage contactor. The results of this hot test are compared with batch extraction studies, where it was found that americium extraction was comparable to batch contacts, while stripping was less efficient than expected. Proposals for the next test are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Adsorption Isotherms for Xenon and Krypton using INL HZ-PAN and AgZ-PAN Sorbents

The generation of adsorption isotherms compliments the scale-up of off-gas processes used to control the emission of encapsulated radioactive volatile fission and activation products released during Used Nuclear Fuel (UNF) reprocessing activities. A series of experiments were conducted to obtain capacity results for varying Kr and Xe gas concentrations using HZ-PAN and AgZ-PAN engineered form sorbents. Gas compositions for Kr ranged from 150-40,000 ppmv and 250-5020 ppmv for Xe in a helium balance. The experiments were all performed at 220 K at a flowrate of 50 sccm. Acquired capacities were then respectively fit to the Langmuir equation using the Langmuir linear regression method to obtain the equilibrium parameters Qmax and Keq. Generated experimental adsorption isotherms were then plotted with the Langmuir predicted isotherms to illustrate agreement between the two. The Langmuir parameters were provided for input into the OSPREY model to predict breakthrough of single component adsorption of Kr and Xe on HZ-PAN and AgZ-PAN sorbents at the experimental conditions tested. Kr and Xe capacities resulting from model breakthrough predictions were then compared to experimental capacities for model validation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Polyacrylonitrile-Chalcogel Hybrid Sorbents for Radioiodine Capture

Powders of a Sn2S3 chalcogen-based aerogel (chalcogel) were combined with powdered polyacrylonitrile (PAN) in different mass ratios (SnS33, SnS50, and SnS70 in mass% of chalcogel), dissolved into dimethyl sulfoxide, and dropped into deionized water to form pellets of a porous PAN-chalcogel hybrid material. Pellets of these hybrid sorbents, along with pure powdered (SnSp) and granular (SnSg) forms of the chalcogel, were then used to adsorb iodine gas under both concentrated and dilute conditions. Both the SnSp and SnSg chalcogels showed very high maximum iodine loadings at 67.2 and 68.3 mass%. The maximum iodine loadings in the SnS33 and SnS50 were high at 32.8 and 53.5 mass%. In all cases, X-ray diffraction results showed the formation of Sn-I phases of SnI4 and SnI4(S8)2 revealing that the iodine binding in these materials is mainly due to a chemisorption process although some evidence also exists that supports a physisorption process.

chalcogel↗

DEVELOPMENT OF A HYDROGEN MORDENITE SORBENT FOR THE CAPTURE OF KRYPTON FROM USED NUCLEAR FUEL REPROCESSING OFF-GAS STREAMS

A novel new sorbent for the separation of krypton from off-gas streams resulting from the reprocessing of used nuclear fuel has been developed and evaluated. A hydrogen mordenite powder was successfully incorporated into a macroporous polymer binder and formed into spherical beads. The engineered form sorbent retained the characteristic surface area and microporosity indicative of mordenite powder. The sorbent was evaluated for krypton adsorption capacities utilizing thermal swing operations achieving capacities of 100 mmol of krypton per kilogram of sorbent at a temperature of 191 K. A krypton adsorption isotherm was also obtained at 191 K with varying krypton feed gas concentrations. Adsorption/desorption cycling effects were also evaluated with results indicating that the sorbent experienced no decrease in krypton capacity throughout testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microfluidic-Based Robotic Sampling System for Radioactive Solutions

A novel microfluidic based robotic sampling system has been developed for sampling and analysis of liquid solutions in nuclear processes. This system couples the use of a microfluidic sample chip with a robotic system designed to allow remote, automated sampling of process solutions in-cell and facilitates direct coupling of the microfluidic sample chip with analytical instrumentation. This system provides the capability for near real time analysis, reduces analytical waste, and minimizes the potential for personnel exposure associated with traditional sampling methods. A prototype sampling system was designed, built and tested. System testing demonstrated operability of the microfluidic based sample system and identified system modifications to optimize performance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterizing diamylamylphosphonate (DAAP) as an Americium Ligand for nuclear fuel cycle applications

Successful deployment of the currently-envisioned advanced nuclear fuel cycle requires the development of a partitioning scheme to separate Am from the lanthanides. The Am/lanthanide separation is challenging since all the metals are normally trivalent and have similar ionic radii. Oxidation of Am to higher oxidation states is one option to achieve such a separation. Hexavalent Am has now been routinely prepared in our laboratory in strongly acidic solution using sodium bismuthate as the oxidant, and then extracted into diamylamylphosphonate/dodecane solution. Here, we have characterized this phosphonate-containing solvent with regard to the extraction of Am, the lanthanides, Cm, other fission product, and/or inert constituents expected in dissolved nuclear fuel. Additionally, the effects of irradiation on dispersion numbers and the phosphonate concentration were investigated.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Novel Sorbent Development and Evaluation for the Capture of Krypton and Xenon from Nuclear Fuel Reprocessing Off-Gas Streams

The release of volatile radionuclides generated during Used Nuclear Fuel reprocessing in the US will most certainly need to be controlled to meet US regulatory emission limits. A US DOE sponsored Off-Gas Sigma Team has been tasked with a multi-lab collaborative research and development effort to investigate and evaluate emissions and immobilization control technologies for the volatile radioactive species generated from commercial Used Nuclear Fuel (UNF) Reprocessing. Physical Adsorption technology is a simpler and potential economical alternative to cryogenic distillation processes that can be used for the capture of krypton and xenon and has resulted in a novel composite sorbent development procedure using synthesized mordenite as the active material. Utilizing the sorbent development procedure, INL sigma team members have developed two composite sorbents that have been evaluated for krypton and xenon capacities at ambient and 191 K temperature using numerous test gas compositions. Adsorption isotherms have been generated to predict equilibration and maximum capacities enabling modeling to support process equipment scale-up.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Novel Sorbent Development and Evaluation for the Capture of Krypton and Xenon from Nuclear Fuel Reprocessing Off-Gas Streams

The release of volatile radionuclides generated during Used Nuclear Fuel reprocessing in the US will most certainly need to be controlled to meet US regulatory emission limits. A US DOE sponsored Off-Gas Sigma Team has been tasked with a multi-lab collaborative research and development effort to investigate and evaluate emissions and immobilization control technologies for the volatile radioactive species generated from commercial Used Nuclear Fuel (UNF) Reprocessing. Physical Adsorption technology is a simpler and potential economical alternative to cryogenic distillation processes that can be used for the capture of krypton and xenon and has resulted in a novel composite sorbent development procedure using synthesized mordenite as the active material. Utilizing the sorbent development procedure, INL sigma team members have developed two composite sorbents that have been evaluated for krypton and xenon capacities at ambient and 191 K temperature using numerous test gas compositions. Adsorption isotherms have been generated to predict equilibration and maximum capacities enabling modeling to support process equipment scale-up.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of radiolytically generated degradation products in the strip section of a TRUEX flowsheet

This report presents a summary of the work performed to meet the FCRD level 2 milestone M3FT-13IN0302053, “Identification of TRUEX Strip Degradation.” The INL radiolysis test loop has been used to identify radiolytically generated degradation products in the strip section of the TRUEX flowsheet. These data were used to evaluate impact of the formation of radiolytic degradation products in the strip section upon the efficacy of the TRUEX flowsheet for the recovery of trivalent actinides and lanthanides from acidic solution. The nominal composition of the TRUEX solvent used in this study is 0.2 M CMPO and 1.4 M TBP dissolved in n-dodecane and the nominal composition of the TRUEX strip solution is 1.5 M lactic acid and 0.050 M diethylenetriaminepentaacetic acid. Gamma irradiation of a mixture of TRUEX process solvent and stripping solution in the test loop does not adversely impact flowsheet performance as measured by stripping americium ratios. The observed increase in americium stripping distribution ratios with increasing absorbed dose indicates the radiolytic production of organic soluble degradation compounds.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗