Engineering Papers⌕ Search

Engineering topics

Lapidus, Saul H.

Publications and source records attributed to Lapidus, Saul H..

53 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Nanoscale Phase Separation and Large Refrigerant Capacity in Magnetocaloric Material LaFe 11.5 Si 1.5

Here, ferromagnetic transitions, the magnetocaloric effect, and the atomic-scale microstructure in an annealed bulk material of LaFe 11.5 Si 1.5 were investigated using magnetic measurements, Mössbauer spectroscopy, high-resolution X-ray diffraction analysis, and high-resolution transmission electron microscopy. The results provide evidence of the coexistence of two ferromagnetic phases with different Curie temperatures. The phase with a Curie temperature of 216 K corresponds to a Si-rich phase of a NaZn 13 -type structure with a small lattice volume, whereas the phase with a Curie temperature of 185 K corresponds to a Si-poor phase of a NaZn 13 -type structure with a large lattice volume. This phase coexistence is observed on a nanometer scale and it can account for inverse thermal hysteresis of the ferromagnetic transition in the Si-rich phase during warming. Furthermore, the phase coexistence helps the bulk material achieve a refrigeration capacity of 170 J kg -1 due to a combination of the magnetocaloric effect in each phase. It is determined that the magnetocaloric effect in the Si-rich and the Si-poor phase brings about a maximum of the total entropy change of -3.55 and -6.80 and J kg -1 K -1 at respective Curie temperatures, respectively. Fundamentally, the phase coexistence indicates coloring of Si atoms in the lattice of a NaZn 13 -type structure and can be attributed to nanoscale phase separation of a disordered precursor during annealing of the bulk material. The nanoscale phase separation may occur in other magnetocaloric materials, thus allowing for improvement of their refrigeration capacity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ambient and High Pressure CuNiSb 2 : Metal-Ordered and Metal-Disordered NiAs-Type Derivative Pnictides

The mineral Zlatogorite, CuNiSb 2 , was synthesized in the laboratory for the first time by annealing elements at ambient pressure (CuNiSb 2 -AP). Rietveld refinement of synchrotron powder X-ray diffraction data indicates that CuNiSb 2 -AP crystallizes in the NiAs-derived structure ( P 3 m 1, #164) with Cu and Ni ordering. The structure consists of alternate NiSb 6 and CuSb 6 octahedral layers via face-sharing. The formation of such structure instead of metal disordered NiAs-type structure ( P 6 3 / mm c, #194) is validated by the lower energy of the ordered phase by first-principle calculations. Interatomic crystal orbital Hamilton population, electron localization function, and charge density analysis reveal strong Ni-Sb, Cu-Sb, and Cu-Ni bonding and long weak Sb-Sb interactions in CuNiSb 2 -AP. The magnetic measurement indicates that CuNiSb 2 -AP is Pauli paramagnetic. First-principle calculations and experimental electrical resistivity measurements reveal that CuNiSb 2 -AP is a metal. The low Seebeck coefficient and large thermal conductivity suggest that CuNiSb 2 is not a potential thermoelectric material. Single crystals were grown by chemical vapor transport. The high pressure sample (CuNiSb 2 -8 GPa) was prepared by pressing CuNiSb 2 -AP at 700 °C and 8 GPa. However, the structures of single crystal and CuNiSb 2 -8 GPa are best fit with a disordered metal structure in the P 3 m 1 space group, corroborated by transmission electron microscopy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-Voltage Phosphate Cathodes for Rechargeable Ca-Ion Batteries

Calcium-ion batteries (CIBs) are under investigation as next-generation energy storage devices due to their theoretically high operating potentials and lower costs tied to the high natural abundance of calcium. However, the development of CIBs has been limited by the lack of available positive electrode materials. In this study, for the first time, we report two functional polyanionic phosphate materials as high-voltage cathodes for CIBs at room temperature. NaV 2 (PO 4 ) 3 electrodes were found to reversibly intercalate 0.6 mol of Ca 2+ (81 mA h g –1 ) near 3.2 V (vs Ca 2+ /Ca) with stable cycling performance at a current density of 3.5 mA g –1 . The olivine framework material FePO 4 reversibly intercalates 0.2 mol of Ca 2+ (72 mA h g –1 ) near 2.9 V (vs Ca 2+ /Ca) at a current density of 7.5 mA g –1 in the first cycle. Structural, electronic, and compositional changes are consistent with reversible Ca 2+ intercalation into these two materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Dynamics of Hydroxyl Anions Promotes Lithium Ion Conduction in Antiperovskite Li 2 OHCl

Li 2 OHCl is an exemplar of the antiperovskite family of ionic conductors, for which high ionic conductivities have been reported, but in which the atomic-level mechanism of ion migration is unclear. The stable phase is both crystallographically defective and disordered, having similar to 1/3 of the Li sites vacant, while the presence of the OH(- )anion introduces the possibility of rotational disorder that may be coupled to cation migration. In this work, complementary experimental and computational methods are applied to understand the relationship between the crystal chemistry and ionic conductivity in Li 2 OHCl , which undergoes an orthorhombic to cubic phase transition near 311 K (approximate to 38 degrees C) and coincides with the more than a factor of 10 change in ionic conductivity (from 1.2 x 10 -5 mS/cm at 37 degrees C to 1.4 x 10 -3 mS/cm at 39 degrees C). X ray and neutron experiments conducted over the temperature range 20-200 degrees C, including diffraction, quasi-elastic neutron scattering (QENS), the maximum entropy method (MEM) analysis, and ab initio molecular dynamics (AIMD) simulations, together show conclusively that the high lithium ion conductivity of cubic Li2OHCl is correlated to "paddlewheel" rotation of the dynamic OH - anion. The present results suggest that in antiperovskites and derivative structures a high cation vacancy concentration combined with the presence of disordered molecular anions can lead to high cation mobility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

In situ investigation of phosphonate retarder interaction in oil well cements at elevated temperature and pressure conditions

In this paper, the effect of a high-performance retarding additive in oil well cements was investigated under elevated temperature (165°C) and pressure (1000 psi) conditions via in situ synchrotron-based X-ray diffraction (XRD) and quasielastic neutron scattering (QENS) techniques. Under these temperature and pressure conditions, crystalline calcium silicate hydrates (C–S–H) are formed through the cement hydration process. From in situ XRD experiments, the retardation effect was observed by a change in the rate of the appearance of 11 Å tobermorites as well as a change in the rate of the α-C 2 SH generation and depletion. QENS analysis revealed that the retardation effect was related to the non-conversion of free water to chemical and constrained water components. A high presence of free water components was attributed to a decrease in 11Å tobermorites along with slower consumption of the quartz and portlandite phases. Furthermore, QENS results infer that the water molecules experienced confinement in the restricted pore spaces. The retarder inhibited this initial water confinement by slowing the bulk diffusion of free water in the confined region.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Synthesis of Antiperovskite Solid Electrolytes: Comparing Li 3 SI, Na 3 SI, and Ag 3 SI

Prior calculations have predicted that chalcohalide anti-perovskites may exhibit enhanced ionic mobility compared to oxyhalide anti-perovskites as solid-state electrolytes. Herein, the synthesis of Ag-, Li- and Na-based chalcohalide anti-perovskites is investigated using first-principle calculations and in situ synchrotron X-ray diffraction. These techniques demonstrate that the formation of Ag 3 SI is facilitated by the adoption of a common body centered cubic packing of S 2– and I – in the reactants and products at elevated temperatures, with additional stabilization achieved by the formation of a solid solution of the anions. Further, the absence of these two features appears to hinder the formation of the analogous Li and Na anti-perovskites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High Capacity for Mg 2+ Deintercalation in Spinel Vanadium Oxide Nanocrystals

Nonaqueous Mg batteries can theoretically reach high energy density with cost-effective materials, yet no such device to date has performance competitive with Li-ion technologies. A major barrier is the need for oxide cathodes that combine high capacity and voltage. Very few oxides have shown intrinsic ability for Mg 2+ intercalation in electrolytes with acceptably low content of H2O. Herein, we demonstrate that nanocrystals of MgV 2 O 4 can reach high capacity for Mg 2+ deintercalation with a mechanism that preserves their spinel framework, validated through measurements with different chemical and structural sensitivity. The structural stability contrasts with other phases where reaching high capacity required distortions that introduce undesirable mechanical strain. The favorable properties of the oxide allowed cycling in a full cell with Mg metal. This work reveals new insights into the viability of multivalent intercalation in oxides, meeting a milestone toward the feasibility of high-voltage batteries with either Mg metal or Mg-ion anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High Voltage Mg-Ion Battery Cathode via a Solid Solution Cr–Mn Spinel Oxide

We discuss how lattice Mg 2+ in a tailored solid solution spinel, MgCrMnO 4 , is electrochemically utilized at high Mn-redox potentials in a nonaqueous electrolyte. Complementary evidence from experimental and theoretical analyses supports bulk Mg 2+ (de)intercalation throughout the designed oxide frame where strong electrostatic interaction between Mg 2+ and O 2- exists. Mg/Mn antisite inversion in the spinel is lowered to similar to 10% via postannealing at 350 degrees C to further improve Mg 2+ mobility. Spinel lattice is preserved upon removal of Mg 2+ without any phase transformations, denoting structural stability at the charged state at a high potential similar to 3.0 V (vs Mg/Mel. Clear remagnesiation upon first discharge, harvesting up to similar to 180 Wh/kg at 60 degrees C is shown. In the remagnesiated state, insertion of Mg 2+ into interstitial sites in the spinel is detected, possibly resulting in partial reversibility which needs to be addressed for structural stability. The observations constitute a first clear path to the development of a practical high voltage Mg-ion cathode using a spinel oxide.

25 ENERGY STORAGE↗
DOE OSTI2020

Synthesis, Crystal Structure, and Cooperative 3d–5d Magnetism in Rock Salt Type Li 4 NiOsO 6 and Li 3 Ni 2 OsO 6

Two new transition metal oxides with the nominal chemical compositions of Li 4 NiOsO 6 and Li 3 Ni 2 OsO 6 were successfully synthesized. Both compounds crystallize in an ordered rock salt structure type in the monoclinic C2/m space group. The crystal structures were determined using both synchrotron X-ray and time-of-flight neutron, powder diffraction data. In both phases, Ni2+ ions are present while oxidation states of osmium are +6 and +5 in Li 4 NiOsO 6 and Li 3 Ni 2 OsO 6 , respectively. Ni2+ ions in the hypothetical fully ordered phase form a honeycomb arrangement in the ab crystallographic plane and these hexagons are centered by osmium ions. Furthermore, the magnetic layers are separated along the c axis by the octahedra, which are centered by Li+ (or Li+/Ni 2+ , depending on the chemical compositions). Crystal structure refinements reveal that there is some degree of mixed occupancy in cationic positions. Temperature dependent magnetic susceptibility data for both phases show ferrimagnetic transitions with predominant antiferromagnetic (AFM) interactions among 3d electrons of nickel and Sd electrons of osmium. Iso-thermal magnetization loops as a function of the applied magnetic field below the transition temperatures confirm the ferrimagnetic nature in magnetic transitions. Temperature dependent heat capacity data, however, did not exhibit any anomaly in either phase, indicating the absence of long-range magnetic ordering. The lack of long-range order for both Os 5+ and Os 6+ -based compounds was also confirmed by low temperature neutron diffraction data down to 10 K. Temperature dependent AC magnetic susceptibility data in various frequencies for both samples indicate that Li 4 NiOsO 6 exhibits spin-glass-like behavior, while the transition temperature for Li 3 Ni 2 OsO 6 is nearly frequency independent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Single-Crystal Growth and Room-Temperature Magnetocaloric Effect of X-Type Hexaferrite Sr 2 Co 2 Fe 28 O 46

X-type hexaferrites have been receiving considerable attention due to their promising applications in many magnetic-electronic fields. However, the growth of single-crystal X-type hexaferrite is still a challenge. Herein we reported, for the first time, the preparation of single crystal X-type hexaferrite Sr 2 Co 2 Fe 28 O 46 (Sr 2 Co 2 X) with high-quality and large size using floating-zone method with laser as the heating source. The crystals show rhombohedral symmetry with space group of R-3m (No. 166, a = 5.8935(1) Å and c = 83.7438(17) Å). Co 2+ and Fe 3+ oxidation states were confirmed by the X-ray absorption near-edge spectroscopy. The prepared Sr 2 Co 2 X exhibits a spin reorientation transition from easy-cone to easy-axis at T 2 of 343 K and a ferrimagnetism–paramagnetism transition at Curie temperature (TC) of ~743 K. The spin reorientation transition was accompanied by magnetocaloric effect (MCE). Both conventional and inverse MCEs were observed near T 2 with a magnetic field applied along the c-axis. The maximum value of the magnetic entropy change along the c-axis was evaluated to be 1.1 J/kg·K for a magnetic field change of 5 T.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Evolution of noncollinear magnetism in magnetocaloric MnPtGa

MnPtGa crystallizes in the hexagonal Ni 2 In structure type in space group P6 3 /mmc and has been reported to display a ferromagnetic Curie temperature near 220K. Here we find a transition near T c = 236 K to a ferromagnetic state, albeit with a reduced moment from what is expected for collinear ordering. The peak magnetocaloric entropy change was determined to be ΔS M = –1.9 J kg –1 K –1 for an applied magnetic field of H = 5 T at the ferromagnetic ordering temperature. Magnetostructural coupling manifests as a change in the slope of the thermal expansion coefficients of the c lattice parameter near T c , with a negative spontaneous volume magnetostriction; ω = –300 ppm at 190K. In this work, neutron powder diffraction studies of the magnetic ground state reveal an evolution in complexity as temperature decreases: from a ferromagnet, to a canted antiferromagnet, to the eventual formation of a spin-density-wave state at low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structure and Negative Thermal Expansion in Zr 0.3 Sc 1.7 Mo 2.7 V 0.3 O 12

A 2 M 3 O 12 -based materials have received considerable attention owing to their wide range of negative thermal expansion (NTE) and chemical flexibility toward novel materials design. However, the structure and NTE mechanism remain challenging. In this paper, Zr 4+ and V 5+ are used as a unit to compensatorily replace Sc 3+ and Mo 6+ in Sc 2 Mo 3 O 12 to tune its thermal expansion. Its crystal structure, phase transition, NTE property, and corresponding mechanisms are studied by high-resolution synchrotron X-ray diffraction, powder X-ray diffraction, ultralow-frequency Raman spectroscopy, and density functional theory calculations. The results show that Zr 0.3 Sc 1.7 Mo 2.7 V 0.3 O 12 adopts an orthorhombic (Pbcn) structure at room temperature, with V atoms occupying the position of Mo1 atoms and Zr atoms occupying the position of Sc atoms, and transforms to monoclinic (P2 1 /a) structure at similar to ~133 K (45 K lower than that of Sc 2 Mo 3 O 12 ). It exhibits excellent NTE in a broader range. Most of the phonon modes below 350 cm -1 have negative Grüneisen parameters, of which the lowest and next-lowest frequency (38.5 and 45.8 cm -1 ) optical phonon modes arising from the translational vibrations of the Sc/Zr and Mo/V atoms in the plane of the nonlinear linkage Sc/Zr-O-Mo/V have the largest and next-largest negative Grüneisen parameters and positive total anharmonicity, and contribute most to the NTE.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-Pressure, High-Temperature Synthesis and Characterization of Polar and Magnetic LuCrWO 6

We report a new polar and magnetic oxide, LuCrWO 6 , was synthesized under high pressure (6 GPa) and high temperature (1673 K). LuCrWO 6 is isostructural with the previously reported polar YCrWO 6 (SG: Pna21, no. 33). The ordering of CrO 6 and WO 6 octahedra in the edge-shared dimers induce the polar structure. The effective size of rare earth, Ln cation does not seem to affect the symmetry of LnCrWO 6 . Second harmonic generation measurements of LuCrWO 6 confirmed the noncentrosymmetric character and strong piezoelectric domains are observed from piezoresponse force microscopy at room temperature. LuCrWO 6 exhibits antiferromagnetic behavior, T N , of ~18 K with a Weiss temperature of -30.7 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enhancing easy-plane anisotropy in bespoke Ni(II) quantum magnets

We examine the crystal structures and magnetic properties of several S = 1 Ni(II) coordination compounds, molecules and polymers, that include the bridging ligands HF 2 - , A F 6 2- ( A = Ti, Zr) and pyrazine or non-bridging ligands F - , SiF 6 2- , glycine, H 2 O, 1-vinylimidazole, 4-methylpyrazole and 3-hydroxypyridine. Pseudo-octahedral NiN 4 F 2 , NiN 4 O 2 or NiN 4 OF cores consist of equatorial Ni-N bonds that are equal to or slightly longer than the axial Ni- L ax bonds. By design, the zero-field splitting ( D ) is large in these systems and, in the presence of substantial exchange interactions ( J ), can be difficult to discriminate from magnetometry measurements on powder samples. Thus, we relied on pulsed-field magnetization in those cases and employed electron-spin resonance (ESR) to confirm D when J ← D . The anisotropy of each compound was found to be easy-plane ( D > 0) and range from ≈ 8–25 K. This work reveals a linear correlation between the ratio d (Ni- L ax )/ d (Ni-N eq ) and D although the ligand spectrochemical properties may play an important role. We assert that this relationship allows us to predict the type of magnetocrystalline anisotropy in tailored Ni(II) quantum magnets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

From Waste-Heat Recovery to Refrigeration: Compositional Tuning of Magnetocaloric Mn 1+ x Sb

Magnetic refrigeration, as well as waste-heat recovery, can be accomplished through the magnetocaloric effect, where temperature changes the magnetic state of a material or vice versa. Promising magnetocaloric materials display large changes in magnetic entropy (ΔS M ) upon application of a moderate magnetic field and are often associated with magnetic materials possessing some degree of magnetostructural coupling. In such compounds, the magnetic transition is coupled to some structural transition at the ordering temperature, and indicators for these are readily calculated by the magnetic deformation proxy Σ M . MnSb, with a Curie temperature T C = 577 K, has a calculated magnetic deformation of Σ M = 5.9% and is a promising candidate material for waste-heat recovery. The temperature dependence of structural, magnetic, and magnetocaloric properties of Mn 1+ x Sb, where $x$ is a tunable amount of interstitial Mn, is studied here. specifically, excess Mn is incorporated as an interstitial whose magnetic moment is antialigned with the stoichiometric Mn, and the excess Mn has the effect of lowering T C , such that the Curie temperature can be tuned from 577 K to nearly room temperature at 318 K for $x$ = 0.2. For $x$ = 0.0, 0.1, and 0.2, values of ΔS M under a maximum magnetic field $H$ = 5 T are found to be 3.65, 3.00, and 2.83 J K -1 kg -1 , respectively. While the maximum ΔS M decreases with $x$, the high refrigerant capacity a more holistic measure of performance-is retained in this highly tunable system.

36 MATERIALS SCIENCE↗