Engineering Papers⌕ Search

Engineering topics

Langston, L. S.

Publications and source records attributed to Langston, L. S..

15 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Asymmetrical boundary layer separation at the base of a two cylinder geometry

This paper reports on the experimental description of the three-dimensional horseshoe vortex system occurring at the base of two cylinder mounted side by side on an endwall. The spacing between the two cylinders is adjusted to generate a family of viscous flows. Flow visualization performed in a water tunnel provides a qualitative understanding of the flow over a range of flow variables. A detailed wind tunnel experiment provides a quantitative description of the flow at a single test condition. At Re(D) = 2.5 x 10 to the 5th the measurements show an asymmetrical primary vortex with a wide flat cross section. A small counterrotating vortex is found between the primary vortex and the cylinder leading edge.

Boyle, M. T.↗
NASA NTRS1988

Three-dimensional flow past two cylinders mounted side by side on an endwall

This paper reports on the experimental description of flow past two cylinders that stand side by side on an endwall. Flow visualization performed in a water tunnel provides a qualitative understanding of the three-dimensional flow over a range of control variables. Limiting streamline flow visualization shows the location of the three-dimensional separation for a range of cylinder spacings. For a spacing of 1.5 diameters between centers, the flow is described using a five-hole probe and by cylinder and endwall surface static pressure measurements. At a cylinder diameter Reynolds number of 250,000 the measurements show a single primary vortex with a wide flat cross section. The velocity measurements show high shear on the endwall in the primary vortex region. A small counterrotating vortex is found between the primary vortex and the cylinder leading edge.

Boyle, M. T.↗
NASA NTRS1986

Measurements of a turbulent horseshoe vortex formed around a cylinder

An experimental investigation was conducted to characterize a symmetrical horseshoe vortex system in front of and around a single large-diameter right cylinder centered between the sidewalls of a wind tunnel. Surface flow visualization and surface static pressure measurements as well as extensive mean velocity and pressure measurements in and around the vortex system were acquired. The results lend new insight into the formation and development of the vortex system. Contrary to what has been assumed previously, a strong vortex was not identified in the streamwise plane of symmetry, but started a significant angular distance away from it. Rather than the multiple vortex systems reported by others, only a single primary vortex and saddle point were found. The scale of the separation process at the saddle point was much smaller than the scale of the approaching boundary layer thickness. Results of the present study not only shed light on such phenomena as the nonsymmetrical endwall flow in axial turbomachinery but can also be used as a test case for three-dimensional computational fluid mechanics computer codes.

Eckerle, W. A.↗
NASA NTRS1986

Horseshoe vortex formation around a cylinder

An experimental investigation was conducted to characterize a symmetrical horseshoe vortex system in front of and a around a single large-diameter right cylinder centered between the sidewalls of a wind tunnel. Surface flow visualization anad surface static pressure measurements as well as extensive mean velocity and pressure measurements in and around the vortex system were acquired. The results lend new insight into the formation and development of the vortex system. Contrary to what has been assumed previously, a strong vortex was not identified in the streamwise plane of symmetry, but started a significant angular distance away from it. Rather than the multiple vortex systems reported by others, only a single primary vortex and saddle point were found. The scale of the separation process at the saddle point was much smaller than the scale of the approaching bundary layer thickness. Results of the present study not only shed light on such phenomena as the nonsymmetrical endwall flow in axial turbomachinery but can also be used as a test case for three-dimensional computational fluid mechanics computer codes.

Eckerle, W. A.↗
NASA NTRS1983

Turbine endwall single cylinder program

Measurements of the flow field in front of a large-scale single cylinder, mounted in a wind tunnel are discussed. Static pressures on the endwall and cylinder surfaces, extensive five-hole probe pressures in front of and around the cylinder, and velocity fluctuations using a hot-wire probe where the flow is steady enough to yield meaningful results are included.

Langston, L. S.↗
NASA NTRS1982

A new surface-streamline flow-visualization technique

This paper describes a new surface-streamline flow-visualization technique that is suitable for use in low-speed wind tunnels or other low-speed gas flows. The technique provides a permanent record of ink traces that show surface-streamline direction and shape. The visualization of the endwall surface flow of the horseshoe-vortex system formed around the base of a cylinder by a separating turbulent boundary layer is used as an example. The results of the new technique are compared with those obtained from a conventional flow-visualization technique. Good agreement was found between the two, with the new technique appearing to give more-accurate surface streamlines.

Langston, L. S.↗
NASA NTRS1982

Turbine endwall single cylinder program

Detailed measurement of the flow field in front of a large-scale single cylinder, mounted in a wind tunnel is discussed. A better understanding of the three dimensional separation occuring in front of the cylinder on the endwall, and of the vortex system that is formed is sought. A data base with which to check analytical and numerical computer models of three dimensional flows is also anticipated.

Langston, L. S.↗
NASA NTRS1981

Turbine endwall two-cylinder program

A series of experiments to study the three dimensional separation of fluid flow around two isolated cylinders mounted on an endwall are described. Topics covered include: (1) water tunnel testing for both the single and double cylinder cases; (2) wind tunnel flow characteristics; (3) static pressure distribution measured on the cylinders; and (4) design and construction of a pressure reference system.

Langston, L. S.↗
NASA NTRS1980

Turbine endwall two-cylinder program

Progress is reported in an effort to study the three dimensional separation of fluid flow around two isolated cylinders mounted on an endwall. The design and performance of a hydrogen bubble generator for water tunnel tests to determine bulk flow properties and to measure main stream velocity and boundary layer thickness are described. Although the water tunnel tests are behind schedule because of inlet distortion problems, tests are far enough along to indicate cylinder spacing, wall effects and low Reynolds number behavior, all of which impacted wind tunnel model design. The construction, assembly, and operation of the wind tunnel and the check out of its characteristics are described. An off-body potential flow program was adapted to calculate normal streams streamwise pressure gradients at the saddle point locations.

Langston, L. S.↗