Engineering Papers⌕ Search

Engineering topics

Lang, Eric

Publications and source records attributed to Lang, Eric.

47 records · Page 3

Helium Bubbles and Blistering in a Nanolayered Metal/Hydride Composite

Helium is insoluble in most metals and precipitates out to form nanoscale bubbles when the concentration is greater than 1 at.%, which can alter the material properties. Introducing controlled defects such as multilayer interfaces may offer some level of helium bubble management. This study investigates the effects of multilayered composites on helium behavior in ion-implanted, multilayered ErD 2 /Mo thin film composites. Following in-situ and ex-situ helium implantation, scanning and transmission electron microscopy showed the development of spherical helium bubbles within the matrix, but primarily at the layer interfaces. Bubble linkage and surface blistering is observed after high fluence ex-situ helium implantation. These results show the ability of metallic multilayers to alter helium bubble distributions even in the presence of a hydride layer, increasing the lifetime of materials in helium environments.

36 MATERIALS SCIENCE↗

PHENIX U.S.-Japan Collaboration Investigation of Thermal and Mechanical Properties of Thermal Neutron–Shielded Irradiated Tungsten

The United States and Japan have collaborated on fusion materials research in a series of agreements reaching back to 1981. The PHENIX collaboration is the latest U.S.-Japan project which spans 2013 to 2019 and has the goal of assessing technical feasibility of tungsten-based, helium-cooled plasma-facing component concepts for a demonstration fusion power reactor (DEMO). Task 2 within the PHENIX project is focused on evaluating the neutron irradiation effects in tungsten. For tungsten, the transmutation to Re and Os is at least as important to determining its properties after irradiation as the displacement damage, and the transmutation rate depends on the energy spectrum of the reactor. A large-scale, instrumented irradiation capsule with thermal neutron shielding to better mimic fusion conditions was irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory. The tungsten specimens were irradiated in different temperature zones between 500°C and 1200°C to doses of ~0.2 to 0.7 displacements per atom. More than 20 varieties of pure tungsten and tungsten alloys were included in the irradiation, and they were evaluated in the 3025E hot-cell facility and at the Low Activation Materials Development and Analysis Laboratory. The elevated temperature tensile, fracture toughness, hardness, thermal conductivity, electrical resistivity, density, elemental composition, and microstructure properties of the irradiated materials are being collected. Furthermore, this paper overviews the experimental design, specimen matrix, and the initial results of postirradiation examinations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pre-Irradiation Comparison of W-Based Alloys for the PHENIX Campaign: Microstructure, Composition, and Mechanical Properties

Tungsten is the material of choice as the plasma-facing material in future plasma-burning fusion reactors. During operation, plasma-facing materials will be simultaneously exposed to 14-MeV neutrons, low-energy D/He particles, and high heat loads. Neutron irradiation of tungsten results in bulk material damage, including knock-on damage causing loops and voids, and transmutation reactions leading to the transmutation of tungsten to rhenium and osmium. Under irradiation to high dose, Re and Os atoms can amalgamate into precipitates that drastically alter the material properties, noticeably increasing the hardness. However, the early-stage development of Re and Os precipitates under a fast neutron spectrum has not been investigated.In this work, the microstructure and hardening behavior of W-Re alloys containing 0 to 2.2 wt% Re, TiC-doped W, and powder-injection-molded W are investigated prior to neutron irradiation at 500ºC and 800ºC to ~0.1 displacement per atom in the High Flux Isotope Reactor (HFIR) to establish a baseline understanding of the starting microstructures.Transmission electron microscopy analysis indicates a dislocation-heavy microstructure, and scanning transmission electron microscopy–energy dispersive spectroscopy shows no spatial segregation of Re and W. Similarly, surface compositional studies performed with electron backscatter diffraction and X-ray photoelectron spectroscopy showed no presence of Re, indicating the Re did not segregate or form new phases during fabrication. Here, the alloys in their as-fabricated state showed no Re segregation or second-phase development, with no significant differences between their microstructures and Vickers hardness values.

36 MATERIALS SCIENCE↗