Engineering topics

Landrum, D. Brian

Publications and source records attributed to Landrum, D. Brian.

16 records

NASA NTRS2019

Marsbee - Swarm of Flapping Wing Flyers for Enhanced Mars Exploration: NASA Innovative Advanced Concepts (NIAC) - Phase I: Final Report

Mars exploration has received significant interest from academia, industry, government, and the general public. Despite continued interest, flying on Mars remains challenging, mainly due to the ultra-thin Martian atmospheric density. Although the gravitational acceleration on Mars is 38 percent of Earth's 9.8 meters per second squared, the Martian atmospheric density is only 1.3 percent of the air density on Earth. The aerodynamic forces are proportional to the ambient fluid density. Therefore, flying near the surface of Mars has been considered nearly impossible. The proposed mission architecture (Fig. 1) consists of a Mars rover (already existing) that serves as a mobile base for Marsbees - a deployable swarm of small bio-inspired flapping wing vehicles. In one ConOps scenario, each Marsbee would carry an integrated stereographic video camera and the swarm could construct a 3D topographic map of the local surface for rover path planning. These flying scouts would provide a "third-dimension" to the rover capabilities. In other scenarios, each part of the swarm of Marsbees could carry pressure and temperature sensors for atmospheric sampling, or small spectral analyzers for identification of mineral outcroppings. In each scenario, the rover acts as a recharging and deployment/return station and data and communication hub. Human exploration of Mars is one of the major objectives of NASA and commercial entities such as SpaceX and Boeing. The identified innovations unique to the bio-inspired flapping Marsbee provide viable multi-mode flying mobility for Martian atmospheric and terrain exploration. A swarm of Marsbees provides an enhanced reconfigurable Mars exploration system that is resilient to individual component failures. These Marsbees can carry sensors and wireless communication devices in combination with a Mars rover and helicopters. These enhanced sensing and information gathering abilities can contribute to the following NASA Mars mission objectives: i) "Determine the habitability of an environment", ii) "Obtain surface weather measurements to validate global atmospheric models", and iii) "Prepare for human exploration on Mars." Various commercial entities, e.g. SpaceX and Boeing, are investing in technologies to transport humans to Mars.

Kang, Chang-kwon↗

NASA NTRS2005

Effect of Tube Geometry on Regenerative Cooling Performance

The flowfield characteristics in a rocket engine coolant channels are analyzed by use of a commercial CFD and multiphysics software developed by the CFD Research Corp. called CFD-ACE+. The channels are characterized by high Reynolds number flow, varying aspect ratio, varying curvature, asymmetric and symmetric heating. The supercritical hydrogen coolant introduces large property variations that have a strong influence on the developing flow and the resulting heat transfer. This paper only shows the effect of aspect ratio and curvature for constant properties.

Parris, Daniel K.↗

NASA NTRS2005

Uncertainty Analysis of Heat Transfer to Supercritical Hydrogen in Cooling Channels

Sound understanding of the cooling efficiency of supercritical hydrogen is crucial to the development of high pressure thrust chambers for regeneratively cooled LOX/LH2 rocket engines. This paper examines historical heat transfer correlations for supercritical hydrogen and the effects of uncertainties in hydrogen property data. It is shown that uncertainty due to property data alone can be as high as 10%. Previous heated tube experiments with supercritical hydrogen are summarized, and data from a number of heated tube experiments are analyzed to evaluate conditions for which the available correlations are valid.

Locke, Justin M.↗

NASA NTRS2001

Analysis of a Nuclear Enhanced Airbreathing Rocket for Earth to Orbit Applications

The proposed engine concept is the Nuclear Enhanced Airbreathing Rocket (NEAR). The NEAR concept uses a fission reactor to thermally heat a propellant in a rocket plenum. The rocket is shrouded, thus the exhaust mixes with ingested air to provide additional thermal energy through combustion. The combusted flow is then expanded through a nozzle to provide thrust.

Adams, Robert B.↗

NASA NTRS2001

Optimization of the SHX Fusion Powered Transatmospheric Propulsion Concept

Existing propulsion technology has not achieved cost effective payload delivery rates to low earth orbit. A fusion based propulsion system, denoted as the Simultaneous Heating and eXpansion (SHX) engine, has been proposed in earlier papers. The SHX couples energy generated by a fusion reactor to the engine flowpath by use of coherent beam emitters. A quasi-one-dimensional flow model was used to quantify the effects of area expansion and energy input on propulsive efficiency for several beam models. Entropy calculations were included to evaluate the lost work in the system.

Adams, Robert B.↗

NASA NTRS1999

Investigation of the Rocket Induced Flow Field in a Rectangular Duct

Rocket-Based Combined Cycle (RBCC) concepts attempt to improve the performance of launch vehicles at all points in the launch trajectory and make highly reusable launch vehicles a reality. The Aerojet Strutjet RBCC concept consists of a variable geometry duct with internal, vertical struts that functions in ducted rocket, ramjet, scramjet, and pure rocket modes. These struts have rocket and turbine exhaust nozzles imbedded within them. The rocket flows create an ejector effect with the ingested air at subsonic flight velocities. In ramjet and scramjet modes, the fuel rich nozzle flows react with the ingested air producing an afterburner effect. Under a NASA Marshall Space Flight Center contract, the UAH Propulsion Research Center (PRC) has designed and built a Strutjet simulation facility. A scale model of a single strut has been built and is undergoing cold-flow testing to investigate the mixing of the rocket and turbine exhausts with the ingested air. A complementary experimental program is also underway to examine the induced flow-field generated by rocket nozzles confined in a rectangular duct. Characterizing the induced flow behavior is critical to understanding and optimizing the performance of future Strutjet-based RBCC propulsion systems. The proposed paper will present results from the rocket induced flow investigation.

Landrum, D. Brian↗

NASA NTRS1999

Investigation of the Rocket Induced Flow Field in a Rectangular Duct

Several tests were performed on a one-sixth scale Rocket Based Combined Cycle (RBCC) engine model at the University of Alabama in Huntsville. The UAH RBCC facility consists of a rectangular duct with a vertical strut mounted in the center. The scaled strut consists of two supersonic rocket nozzles with an embedded vertical turbine between the rocket nozzles. The tests included mass flow, flow visualization and horizontal pressure traverses. The mass flow test indicated a c:hoked condition when the rocket chamber pressure is between 200 psi and 300 psi. The flow visualization tests narrowed the rocket chamber pressure range from, 250 psi to 300 psi. Also, from this t.est, an assumption of a minimum <area choke was made. Horizontal pressure traverses were performed at locations both upstream and downstream of the nozzle exit plane. These traverses aided in examining the induced airflow due to the ejector effect and the growth of the: boundary layer in the strut sidewall gap.

Landrum, D. Brian↗

NASA NTRS1998

Assessment of Uncertainty in the Determination of Activation Energy for Polymeric Materials

An assessment of the experimental uncertainty in obtaining the kinetic activation energy from thermogravimetric analysis (TGA) data is presented. A neat phenolic resin, Borden SC1O08, was heated at three heating rates to obtain weight loss vs temperature data. Activation energy was calculated by two methods: the traditional Flynn and Wall method based on the slope of log(q) versus 1/T, and a modification of this method where the ordinate and abscissa are reversed in the linear regression. The modified method produced a more accurate curve fit of the data, was more sensitive to data nonlinearity, and gave a value of activation energy 75 percent greater than the original method. An uncertainty analysis using the modified method yielded a 60 percent uncertainty in the average activation energy. Based on this result, the activation energy for a carbon-phenolic material was doubled and used to calculate the ablation rate In a typical solid rocket environment. Doubling the activation energy increased surface recession by 3 percent. Current TGA data reduction techniques that use the traditional Flynn and Wall approach to calculate activation energy should be changed to the modified method.

Darby, Stephania P.↗

NASA NTRS1998

Mixing of Supersonic Streams

The Strutjet approach to Rocket Based Combined Cycle (RBCC) propulsion depends upon fuel-rich flows from the rocket nozzles and turbine exhaust products mixing with the ingested air for successful operation in the ramjet and scramjet modes. A model of the Strutjet device has been built and is undergoing test to investigate the mixing of the streams as a function of distance from the Strutjet exit plane. Initial cold flow testing of the model is underway to determine both, the behavior of the ingested air in the duct and to validate the mixing diagnostics. During the tests, each of the two rocket nozzles ejected up to two pounds mass per second into the 13.6 square inch duct. The tests showed that the mass flow of the rockets was great enough to cause the entrained air to go sonic at the strut, which is the location of the rocket nozzles. More tests are necessary to determine whether the entrained air chokes due to the reduction in the area of the duct at the strut (a physical choke), or because of the addition of mass inside the duct at the nozzle exit (a Fabri choke). The initial tests of the mixing diagnostics are showing promise.

Hawk, Clark W.↗

NASA NTRS1998

Mixing of Supersonic Streams

The Strutjet approach to Rocket Based Combined Cycle (RBCC) propulsion depends upon fuel-rich flows from the rocket nozzles and turbine exhaust products mixing with the ingested air for successful operation in the ramjet and scramjet modes. It is desirable to delay this mixing process in the air-augmented mode of operation present during low speed flight. A model of the Strutjet device has been built and is undergoing test to investigate the mixing of the streams as a function of distance from the Strutjet exit plane during simulate low speed flight conditions. Cold flow testing of a 1/6 scale Strutjet model is underway and nearing completion. Planar Laser Induced Fluorescence (PLIF) diagnostic methods are being employed to observe the mixing of the turbine exhaust gas with the gases from both the primary rockets and the ingested air simulating low speed, air augmented operation of the RBCC. These diagnostics are supplemented by pressure profile measurements across the various jet streams present in the flow duct downstream of the model exit plane. The results of these experiments will be presented.

Hawk, Clark W.↗

NASA NTRS1997

Mixing of Supersonic Streams

The Strutjet approach to Rocket Based Combined Cycle (RBCC) propulsion depends upon fuel-rich flows from the rocket nozzles and turbine exhaust products mixing with the ambient air for successful operation in the ramjet and scramjet modes. A model of the Strutjet device has been built and is undergoing test to investigate the mixing of the streams as a function of distance from the Strutjet exit plane. The modeling basis was centered on using convective Mach Number as the similarity parameter to establish correlation between subscale, cold flow tests and full scale, hot firing modes. This parameter has been used successfully to correlate supersonic shear layer growth rates. The experiment design includes hot (600 R) air as the rocket exhaust simulant and hot (760 R) carbon dioxide as the turbine exhaust gas simulant. The combination of gases and their elevated temperatures was required to achieve a convective Mach Number which matched the fall scale item design conditions. The carbon dioxide is seeded with Acetone to permit tracing of the mixing processes through Laser Induced Fluorescence (LIF) techniques. The experiment and its design will be discussed in detail. Both the rocket and turbine exhaust duct nozzles are of unique (square and rectangular) shape and the turbine exhaust e)dt intersects the rocket nozzle wall upstream of the exit. Cold flow testing with the individual nozzles has been conducted to ascertain their behavior in comparison to conventional flow theory. These data are presented.

Hawk, Clark W.↗

NASA NTRS1996

Assessment of Uncertainty in the Determination of Kinetic Reaction Parameters for Polymeric Materials

The use of thermogravimetric analysis to obtain data describing the thermal response of a polymeric resin with temperature. This data can then be used to obtain activation energy and pre-exponential factor used in an Arrhenius representation of material ablation. The methods which allow to assess the uncertainties associated with the experimental determination of activation energy and pre-exponential factor are employed.

Darby, Stephanie P.↗

NASA NTRS1995

Parametric study of solar thermal rocket nozzle performance

This paper details a numerical investigation of performance losses in low-thrust solar thermal rocket nozzles. The effects of nozzle geometry on three types of losses were studied; finite rate dissociation-recombination kinetic losses, two dimensional axisymmetric divergence losses, and compressible viscous boundary layer losses. Short nozzle lengths and supersonic flow produce short residence times in the nozzle and a nearly frozen flow, resulting in large kinetic losses. Variations in geometry have a minimal effect on kinetic losses. Divergence losses are relatively small, and careful shaping of the nozzle can nearly eliminate them. The boundary layer in these small nozzles can grow to a major fraction of nozzle radius, and cause large losses. These losses are attributed to viscous drag on the nozzle walls and flow blockage by the boundary layer, especially in the throat region. Careful shaping of the nozzle can produce a significant reduction in viscous losses.

Pearson, J. Boise↗

NASA NTRS1994

Computational simulation of liquid fuel rocket injectors

A major component of any liquid propellant rocket is the propellant injection system. Issues of interest include the degree of liquid vaporization and its impact on the combustion process, the pressure and temperature fields in the combustion chamber, and the cooling of the injector face and chamber walls. The Finite Difference Navier-Stokes (FDNS) code is a primary computational tool used in the MSFC Computational Fluid Dynamics Branch. The branch has dedicated a significant amount of resources to development of this code for prediction of both liquid and solid fuel rocket performance. The FDNS code is currently being upgraded to include the capability to model liquid/gas multi-phase flows for fuel injection simulation. An important aspect of this effort is benchmarking the code capabilities to predict existing experimental injection data. The objective of this MSFC/ASEE Summer Faculty Fellowship term was to evaluate the capabilities of the modified FDNS code to predict flow fields with liquid injection. Comparisons were made between code predictions and existing experimental data. A significant portion of the effort included a search for appropriate validation data. Also, code simulation deficiencies were identified.

Landrum, D. Brian↗

NASA NTRS1993

CFD simulation of coaxial injectors

The development of improved performance models for the Space Shuttle Main Engine (SSME) is an important, ongoing program at NASA MSFC. These models allow prediction of overall system performance, as well as analysis of run-time anomalies which might adversely affect engine performance or safety. Due to the complexity of the flow fields associated with the SSME, NASA has increasingly turned to Computational Fluid Dynamics (CFD) techniques as modeling tools. An important component of the SSME system is the fuel preburner, which consists of a cylindrical chamber with a plate containing 264 coaxial injector elements at one end. A fuel rich mixture of gaseous hydrogen and liquid oxygen is injected and combusted in the chamber. This process preheats the hydrogen fuel before it enters the main combustion chamber, powers the hydrogen turbo-pump, and provides a heat dump for nozzle cooling. Issues of interest include the temperature and pressure fields at the turbine inlet and the thermal compatibility between the preburner chamber and injector plate. Performance anomalies can occur due to incomplete combustion, blocked injector ports, etc. The performance model should include the capability to simulate the effects of these anomalies. The current approach to the numerical simulation of the SSME fuel preburner flow field is to use a global model based on the MSFC sponsored FNDS code. This code does not have the capabilities of modeling several aspects of the problem such as detailed modeling of the coaxial injectors. Therefore, an effort has been initiated to develop a detailed simulation of the preburner coaxial injectors and provide gas phase boundary conditions just downstream of the injector face as input to the FDNS code. This simulation should include three-dimensional geometric effects such as proximity of injectors to baffles and chamber walls and interaction between injectors. This report describes an investigation into the numerical simulation of GH2/LOX coaxial injectors. The following sections will discuss the physical aspects of injectors, the CFD code employed, and preliminary results of a simulation of a single coaxial injector for which experimental data is available. It is hoped that this work will lay the foundation for the development of a unique and useful tool to support the SSME program.

Landrum, D. Brian↗

NASA NTRS1991

Vibration-dissociation coupling in nonequilibrium flows

The purpose of the study is to evaluate all important physical phenomena contributing to the vibration-dissociation problem by developing a numerical technique for the simulation of the vibrational relaxation and dissociation/recombination of N(2) in an isothermal box. A set of coupled master equations representing each vibrational level of N(2) is solved, and both V-V and V-T exchanges between molecules and atoms are included, along with the effects of dissociation and recombustion from/to each level. It is observed that the inverse range parameter has a strong impact on the vibrational exchange rates and relaxation. In a heating case, the lower vibrational levels relax through a series of equilibrium distributions, while in a cooling case, a population inversion is formed in the upper levels. Other cases of heating and cooling will be simulated, and together with this work, used to develop a matrix of nonequilibrium relaxation runs.

Landrum, D. Brian↗