Engineering Papers⌕ Search

Engineering topics

Lamar, J. E.

Publications and source records attributed to Lamar, J. E..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Minimum trim drag design for interfering lifting surfaces using vortex-lattice methodology

A new method has been developed by which the mean camber surface can be determined for trimmed noncoplanar planforms with minimum vortex drag under subsonic conditions. The method uses a vortex lattice and overcomes previous difficulties with chord loading specification; it uses a Trefftz plane analysis to determine the optimum span loading for minimum drag, then solves for the mean camber surface of the wing which will provide the required loading. Pitching-moment or root-bending-moment constraints can be employed as well at the design lift coefficient. Sensitivity studies of vortex-lattice arrangement have been made with this method and are presented. Comparisons with other theories show generally good agreement. The versatility of the method is demonstrated by applying it to (1) isolated wings, (2) wing-canard configurations, (3) a tandem wing, and (4) a wing-winglet configuration.

Lamar, J. E.↗
NASA NTRS1976

Sample wings for study

Two simple wings were selected for study using the various implementations (old and new) of the vortex lattice method. These are: (1) a rectangular wing with an aspect ratio of 2, and (2) a tapered wing with an aspect ratio of 5, a taper ratio of 0.5, a leading sweep of 3.317 deg., and a trailing edge sweep of 1-11.308 deg. This was done in order to gain an appreciation for the accuracy of the various implementations. References were given where force, moment, and pressure data could be found for these wings.

Lamar, J. E.↗
NASA NTRS1975

Subsonic aerodynamic characteristics of interacting lifting surfaces with separated flow around sharp edges predicted by a vortex-lattice method

Because the potential flow suction along the leading and side edges of a planform can be used to determine both leading- and side-edge vortex lift, the present investigation was undertaken to apply the vortex-lattice method to computing side-edge suction force for isolated or interacting planforms. Although there is a small effect of bound vortex sweep on the computation of the side-edge suction force, the results obtained for a number of different isolated planforms produced acceptable agreement with results obtained from a method employing continuous induced-velocity distributions. By using the method outlined, better agreement between theory and experiment was noted for a wing in the presence of a canard than was previously obtained.

Lamar, J. E.↗
NASA NTRS1975

Prediction of vortex flow characteristics of wings at subsonic and supersonic speeds

The leading-edge-suction analogy of Polhamus, which has been successful in the prediction of vortex lift characteristics on wings with pointed tips at subsonic and supersonic speeds, has recently been extended to account for the vortex flow characteristics for wings with side edges. Comparisons of experimental data and other currently used methods with the extended method are made for wings having side edges at subsonic and supersonic speeds. Recent data obtained for a low-aspect-ratio cropped-delta wing with various amounts of asymmetrical tip rake, simulating a roll control device, are also presented.

Lamar, J. E.↗
NASA NTRS1974

Extension of leading-edge-suction analogy to wings with separated flow around the side edges at subsonic speeds

A method for determining the lift, drag, and pitching moment for wings which have separated flow at the leading and side edges with subsequently reattached flow downstream and inboard is presented. Limiting values of the contribution to lift of the side-edge reattached flow are determined for rectangular wings. The general behavior of this contribution is computed for rectangular, cropped-delta, cropped-diamond, and cropped-arrow wings. Comparisons of the results of the method and experiment indicate reasonably good correlation of the lift, drag, and pitching moment for a wide planform range. The agreement of the method with experiment was as good as, or better than, that obtained by other methods. The procedure is computerized and is available from COSMIC as NASA Langley computer program A0313.

Lamar, J. E.↗
NASA NTRS1974

Theoretical and experimental longitudinal aerodynamic characteristics of an aspect ratio 0.25 sharp-edge delta wing at subsonic, supersonic, and hypersonic speeds

The suction analogy concept of Polhamus for predicting vortex lift in conjunction with an appropriate potential-flow solution is called the present method. This method is applied to an aspect ratio 0.25 sharp-edge delta wing from a Mach number of 0.143 to 10.4 in free air and at 0.074 in ground effect, and also to an aspect ratio 0.35 triangular crosssectional body at a Mach number of 6.9. The models had subsonic leading edges at the test Mach numbers. Vortex-flow effects could be neither confirmed nor denied to exist at high speeds because of the lack of flow visualization above a Mach number of 0.143. The data, however, could be better predicted by including a vortex-flow effect, although not always to the extent predicted from the present method because of the presence of actual and hypothesized unmodeled flow situations. The method of Nenni and Tung (NASA CR-1860) tended to confirm the existence of vortex flow at hypersonic speeds. The hypersonic-tangent-cone method predicted best the delta-wing results over the test angle-of-attack range and hypersonic Mach number range and did equally as well as the present method for the triangular body.

Fox, C. H., Jr.↗
NASA NTRS1972

Application of the leading edge suction analogy to prediction of longitudinal load distribution and pitching moments for sharp edged delta wings

The leading-edge-suction analogy of Polhamus has been used to develop the longitudinal load distribution of the vortex lift for delta wings. This distribution is shown to be similar in shape to that of the potential-flow longitudinal loading for delta wings having aspect ratios of 2 or less. The totals of the two theoretical distributions for delta wings with an aspect ratio near 1 are in good agreement with the experimentally determined loadings over the angle-of-attack range from 0 to 30 deg. The corresponding predicted pitching moments show slightly more stability than those measured, because of loss of lift near the wing tips.

Snyder, M. H., Jr.↗
NASA NTRS1971

Nonplanar Method for Predicting Incompressible Aerodynamic Coefficients of Rectangular Wings with Circular-Arc Camber

The development of a nonplanar lifting surface method having a continuous distribution of singularities and satisfying the tangent flow boundary condition on the mean camber surface is given. The method predicts some incompressible longitudinal aerodynamic coefficients of rectangular wings which have circular-arc camber. The solution method is of the integral-equation type and the resulting surface integrals are evaluated by either using numerical or analytical techniques, as are appropriate. Applications are made and the results compared with those from an exact two-dimensional circular-arc camber solution, a three-dimensional flat-wing solution which represents the camber by a projected slope onto the flat surface, and a flat-wing experiment. From these comparisons, the present method is found to predict well the flat-wing experiment and limiting values, in addition to the center of pressure variation at an angle of attack of zero for any camber. For wings having camber ratios larger than about 1.25% and moderate to high aspect ratios, the results deterioriate due to the inadequacy of lifting pressure modes employed.

Lamar, J. E.↗
NASA NTRS1968

Modified Multhopp mean camber computer program

Computer program which determines the mean camber surface required to support a given set of loadings on a composite wing in subsonic compressible flow has been developed.

Lamar, J. E.↗
NASA NTRS1968

Modified Multhopp lifting surface loading program

Computer program determines the longitudinal subsonic aerodynamic characteristics of composite wings. The program uses the basic theoretical method of Multhopp in predicting the loading data.

Lamar, J. E.↗