Engineering topics

Lakshminarayana, B.

Publications and source records attributed to Lakshminarayana, B..

At least 91 records · Page 5

NASA NTRS1982

Three-dimensional flow field in the tip region of a compressor rotor passage. II - Turbulence properties

The turbulence properties in the annulus wall region of an axial flow compressor rotor was measured using a triaxial, hot-wire probe rotating with the rotor. The flow was surveyed across the entire passage at five axial locations (leading edge, 1/4 chord, 1/2 chord, 3/4 chord, and the trailing edge location) and at six radial locations in a low-speed compressor rotor. The data derived include all three components of turbulence intensity and three components of turbulence stress. A comprehensive interpretation of the data with emphasis on features related to rotation, leakage flow, annulus wall boundary layer, and blade boundary layer interactions is included. All the components of turbulent intensities and stresses are found to be high in the leakage-flow mixing region. The radial component of intensities and stresses is found to be much higher than the corresponding streamwise components. The turbulent spectra clearly reveal the decay process of the inlet-guide-vane wake within the rotor passage.

Lakshminarayana, B.↗

NASA NTRS1982

Three sensor hot wire/film technique for three dimensional mean and turbulence flow field measurement

Methods of measuring the three dimensional flow field using a three-sensor, hot-wire probe is described in this paper, with emphasis on the techniques developed by the author's group at The Pennsylvania State University. The hot wire equations, data processing procedure, calibration techniques, and a discussion of various errors in the measurement are included. Some typical data acquired by this probe is also included.

Lakshminarayana, B.↗

NASA NTRS1982

Numerical analysis and FORTRAN program for the computation of the turbulent wakes of turbomachinery rotor blades, isolated airfoils and cascade of airfoils

Turbulent wakes of turbomachinery rotor blades, isolated airfoils, and a cascade of airfoils were investigated both numerically and experimentally. Low subsonic and incompressible wake flows were examined. A finite difference procedure was employed in the numerical analysis utilizing the continuity, momentum, and turbulence closure equations in the rotating, curvilinear, and nonorthogonal coordinate system. A nonorthogonal curvilinear coordinate system was developed to improve the accuracy and efficiency of the numerical calculation. Three turbulence models were employed to obtain closure of the governing equations. The first model was comprised to transport equations for the turbulent kinetic energy and the rate of energy dissipation, and the second and third models were comprised of equations for the rate of turbulent kinetic energy dissipation and Reynolds stresses, respectively. The second model handles the convection and diffusion terms in the Reynolds stress transport equation collectively, while the third model handles them individually. The numerical results demonstrate that the second and third models provide accurate predictions, but the computer time and memory storage can be considerably saved with the second model.

Hah, C.↗

NASA NTRS1982

Measurement and prediction of mean velocity and turbulence structure in the near wake of an airfoil

An experimental investigation of the near wake of a thin airfoil at various incidence angles is reported in this paper. The airfoil (NACA 0012 basic thickness form) was located in a wind tunnel, and the wake structure was measured using hot-wire sensors. The measurements of mean-velocity, turbulence intensity and Reynolds-stress components across the wake at several distances downstream show the complex nature of the near wake and its asymmetrical behavior. The asymmetry in the wake property, which is maintained up to a length of 1.5 chords downstream of the trailing edge of the blade, is dependent on the incidence angle of the inlet flow. The streamwise velocity defect in an asymmetric wake decays more slowly compared to that of a symmetric wake. The streamline curvature due to the blade loading has a substantial effect on the mean velocity profile as well as the turbulence structure. The numerical study of the same wake indicates that the existing turbulence closure models need some modification to account for the asymmetric characteristics of the wake.

Hah, C.↗

NASA NTRS1982

Three dimensional flow field inside compressor rotor, including blade boundary layers

The flow in a turbomachinery blade passage has a predominant flow direction. The viscous diffusion in the streamwise direction is usually small and the elliptic influence is transmitted upstream through the pressure field. Starting with a guessed pressure field, it is possible to converge on the full elliptic solution by iterating between a parabolic solution and an iteration of the pressure field. The main steps of the calculation are given. The blade boundary layers which are three dimensional with laminar, transitional, turbulent, and separation zones are investigated. The kinetic energy is analyzed, and the dissipation equation is presented. Measurements were made of the three dimensional flow inside an axial flow compressor passage.

Pouagare, M.↗

NASA NTRS1982

Effects of blade loading and rotation on compressor rotor wake in end wall regions

This study was carried out to understand the effects of blade loading and rotation on the rotor end wall flow structure, including the wake. The measurements were taken with a stationary three sensor hot wire located at the exit of a compressor rotor. The signal was ensemble averaged to derive all the three components of velocity and six components of stresses at the exit. Measurements were made at two different rotational speeds (1753 and 1010 rpm) and at two differing blade loadings at several radii near the hub and the annulus wall. The wake decay in the annulus wall region is found to be much more rapid than the mid span regions. Furthermore, both the loading and rotation of the blade have appreciable influence on the end wall flow and wake structure. Interaction of the annulus and hub wall boundary layers (and secondary flow resulting from these) have appreciable influence on the wake structure in the endwall regions.

Lakshminarayana, B.↗

NASA NTRS1982

Experimental study of the boundary layer on a turbomachinery rotor blade

The development of the turbulent boundary layer on a turbomachinery rotor blade is very complex. This paper is concerned with the measurement, analysis, and prediction of the blade boundary layer on a rotor blade. A comprehensive measurement of the blade boundary layer on a fan rotor blade was carried out in the axial flow fan facility at the Applied Research Laboratory. The measurements were taken with a miniature 'x' configuration hot-wire probe. The streamwise and the radial velocity profiles as well as the turbulence intensities at one radius are presented and interpreted.

Lakshminarayana, B.↗

NASA NTRS1981

Analytical and experimental study of flow phenomena in noncavitating rocket pump inducers

The flow processes in rocket pump inducers are summarized. The experimental investigations were carried out with air as the test medium. The major characteristics features of the rocket pump inducers are low flow coefficient (0.05 to 0.2) large stagger angle (70 deg to 85 deg) and high solidity blades of little or no camber. The investigations are concerned with the effect of viscosity not the effects of cavitation. Flow visualization, conventional and hot wire probe measurement inside and at the exit of the blade passage, were the analytical methods used. The experiment was carried out using four three and two bladed inducers with cambered blades. Both the passage and the exit flow were measured. The basic research and boundary layer investigation was carried out using a helical flat plate (of some dimensions as the inducer blades tested), and flat plate helical inducer (four bladed). Detailed mean and turbulence flow field inside the passage as well as the exit of the rotor were derived from these measurement. The boundary layer, endwall, and other passage data reveal extremely complex nature of the flow, with major effects of viscosity present across the entire passage. Several analyses were carried out to predict the flow field in inducers. These included an approximate analysis, the shear pumping analysis, and a numerical solution of exact viscous equations with approximate modeling for the viscous terms.

Lakshminarayana, B.↗

NASA NTRS1981

End wall flows in rotors and stators of a single stage compressor

A solution of the flow in the rotor end wall region, including the effects of tip clearance flow, is presented. A method for leakage flow measurement at the tip of a compressor rotor blade is discussed. Measurements are given for a rotor hub wall boundary layer.

Govindam, T. R.↗

NASA NTRS1981

Freestream turbulence effects on the development of a rotor wake

The effect of freestream turbulence on the development of a three-dimensional wake of a compressor rotor blade was studied experimentally. The turbulence level at the inlet of a rotor was varied systematically using grids upstream of the rotor. The rotor wake was measured with inlet turbulence intensities of 0.5, 3, and 5%. The experimental results indicate that the maxium change in the mean velocity defect is 4% over the range of inlet turbulence levels employed, while the turbulence structure in the wake is altered more substantially. The freestream turbulence effect was also analyzed, numerically, using the modified Reynolds stress closure model. The comparison between numerical prediction and experimental data shows that the freestream turbulence effect can be represented successfully with the turbulence closure model employed in this paper.

Hah, C.↗

NASA NTRS1981

Interaction of compressor rotor blade wake with wall boundary layer/vortex in the end-wall region

This paper reports the experimental study of the three-dimensional characteristics of the mean velocity of the rotor wake inside the annulus- and hub-wall boundary layers. The measurements were taken with a rotating three-sensor hot wire behind the rotor. This set of measurements probably represents the first set of comprehensive measurements taken inside the annulus- and hub-wall boundary layers. The wake was surveyed at several radial locations inside the boundary layer region and at several axial locations. Interaction of the wake with the annulus-wall boundary layer, secondary flow, tip-leakage flow, and the trailing vortex system results in slower decay and larger width of the wake. The presence of a strong vortex and its merger with the wake is also observed. The end-wall boundary layers and the secondary flow were found to have a substantial effect on both the decay characteristics and the profile of the wake. These and other measurements are reported and interpreted in this paper.

Lakshminarayana, B.↗

NASA NTRS1981

Rotor wake mixing effects downstream of a compressor rotor

An experimental study of rotor wake was conducted in the trailing-edge and near-wake regions of a moderately loaded compressor rotor blade using a rotating triaxial hot-wire probe in a rotating frame of reference. The flow-field was surveyed very close to the trailing-edge as well as inside the annulus- and hub-wall boundary layers. The large amount of data acquired during this program has been analyzed to discern the decay effects as well as the spanwise variation of three components of velocity, three components of intensities and three components of shear stresses. The data set also include extensive information on the variation of the flow properties downstream. The other derived quantities include wake momentum thickness and deviation angles at various spanwise and downstream locations. These data are presented and interpreted, with emphasis on the downstream mixing as well as endwall-wake interaction effects.

Ravindranath, A.↗

NASA NTRS1981

Characteristics of mean velocity in the annulus wall region at the exit of turbomachinery rotor passage

This paper reports the experimental study of the three-dimensional characteristics of the mean velocity in the annulus-wall boundary layer and wake mixing region of a moderately loaded compressor rotor blade. The measurements reported were obtained using a three-sensor hot-wire probe at the exit of the rotor. They consisted of tangential surveys at several axial and radial locations downstream of the compressor rotor blade passage. The variation of the streamwise, normal, and radial velocity profiles and their decay characteristics are derived from this data. The measurements reveal the highly complex and three-dimensional nature of the annulus-wall flow field and the nature of the interaction of the annulus-wall boundary layer, the blade boundary layers and wake, and the secondary flow associated with the annulus-wall region.

Davino, R.↗

NASA NTRS1981

Analysis of turbulent boundary layer on cascade and rotor blades of turbomachinery

The momentum integral technique for predicting the boundary layer growth in three-dimensional flow has been extended to include the entrainment equation as the closure model. The numerical solution is compared with the cascade, inducer, compressor, and fan rotor blade data from various sources. The agreement is found to be excellent in all cases, with the exception of the separated flow. Both the momentum thickness and the limiting streamline angle predicted from this analysis compare well with the measured data for a rotor blade. The technique is extremely useful in engineering design, analysis, and performance prediction.

Lakshminarayana, B.↗

NASA NTRS1981

Effects of rotation and blade incidence on the properties of turbomachinery rotor wake

An experimental investigation of the effects of the speed of rotation on a turbomachinery rotor blade wake was conducted using a fan rotor in incompressible flow. Measurements were made at two different rotational speeds (1753 and 1010 rpm) but keeping the same blade loading. This was achieved by maintaining the same incidence angle to the rotor blades in both sets of measurements. The blade incidence angle was also varied to discern the effect of blade loading. A tri-axial hot wire probe mounted in a stationary frame of reference was used for the measurements made at several radial and axial stations in the near- and far-wake regions. The three dimensional mean velocity and turbulence profiles, the wake defect, wake decay rate, turbulence intensities and turbulence stresses are appreciably altered when the speed of rotation and the blade loading are changed. The wake defect is substantially reduced and the radial velocity increased when the rotational speed is increased.

Lakshminarayana, B.↗

NASA NTRS1980

Analytical and experimental study of mean flow and turbulence characteristics inside the passages of an axial flow inducer

The inviscid and viscid effects existing within the passages of a three bladed axial flow inducer operating at a flow coefficient of 0.065 are investigated. The blade static pressure and blade limiting streamline angle distributions were determined and the three components of mean velocity, turbulence intensities, and turbulence stresses were measured at locations inside the inducer blade passage utilizing a rotating three sensor hotwire probe. Applicable equations were derived for the hotwire data reduction analysis and solved numerically to obtain the appropriate flow parameters. The three dimensional inviscid flow in the inducer was predicted by numerically solving the exact equations of motion, and the three dimensional viscid flow was predicted by incorporating the dominant viscous terms into the exact equations. The analytical results are compared with the experimental measurements and design values where appropriate. Radial velocities are found to be of the same order as axial velocities within the inducer passage, confirming the highly three dimensional characteristic of inducer flow. Total relative velocity distribution indicate a substantial velocity deficiency near the tip at mid-passage which expands significantly as the flow proceeds toward the inducer trailing edge. High turbulence intensities and turbulence stresses are concentrated within this core region. Considerable wake diffusion occurs immediately downstream of the inducer trailing edge to decay this loss core. Evidence of boundary layer interactions, blade blockage effects, radially inward flows, annulus wall effects, and backflows are all found to exist within the long, narrow passages of the inducer.

Gorton, C. A.↗

NASA NTRS1980

Three dimensional mean flow and turbulence characteristics of the near wake of a compressor rotor blade

The investigation was carried out using the rotating hot wire technique. Measurements were taken inside the end wall boundary layer to discern the effect of annulus and hub wall boundary layer, secondary flow, and tip leakage on the wake structure. Static pressure gradients across the wake were measured using a static stagnation pressure probe insensitive to flow direction changes. The axial and the tangential velocity defects, the radial component of velocity, and turbulence intensities were found to be very large as compared to the near and far wake regions. The radial velocities in the trailing edge region exhibited characteristics prevalent in a trailing vortex system. Flow near the blade tips found to be highly complex due to interaction of the end wall boundary layers, secondary flows, and tip leakage flow with the wake. The streamwise curvature was found to be appreciable near the blade trailing edge. Flow properties in the trailing edge region are quite different compared to that in the near and far wake regions with respect to their decay characteristics, similarity, etc. Fourier decomposition of the rotor wake revealed that for a normalized wake only the first three coefficients are dominant.

Ravindranath, A.↗

NASA NTRS1980

Structure and decay characteristics of turbulence in the near- and far-wake of a moderately loaded compressor rotor-blade

The wake of a turbomachinery rotor-blade is turbulent, highly three-dimensional, and nonisotropic with appreciable curvature in the trailing-edge and near-wake regions. The characteristics of the turbulence vary considerably with radius, blade loading, free-stream turbulence, Reynolds number, and the rotor-blade geometry. This paper is concerned with the turbulence properties of a moderately loaded compressor blade, particularly near the blade trailing-edge. The tangential variation of the axial, tangential and radial intensities and stresses across the wake, as well as their decay characteristics were measured with a tri-axial hot-wire probe in the rotor frame of reference. The decay of intensities and stresses were found to be very rapid in the trailing-edge and near-wake regions and slow in the far-wake region. The effects of inlet-guide-vane and the hub-wall boundary layers on the rotor wake turbulence spectra are also discussed. Similarity rules for the three components of intensity are also derived and presented in this paper.

Ravindranath, A.↗