Engineering Papers⌕ Search

Engineering topics

La Lone, B. M.

Publications and source records attributed to La Lone, B. M..

Suppression of Richtmyer-Meshkov Instability via Special Pairs of Shocks and Phase Transitions

The classical Richtmyer-Meshkov instability (RMI) is a hydrodynamic instability characterizing the evolution of an interface following shock loading. In contrast to other hydrodynamic instabilities such as Rayleigh-Taylor, it is known for being unconditionally unstable: regardless of the direction of shock passage, any deviations from a flat interface will be amplified. In this article, we show that for negative Atwood numbers, there exist special sequences of shocks which result in a nearly perfectly suppressed instability growth. Here, we demonstrate this principle computationally and experimentally with stepped fliers and phase transition materials. A fascinating immediate corollary is that in specific instances, a phase-transitioning material may self-suppress RMI.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Non-Richtmyer–Meshkov instability ejecta production based on shallow bubble collapse

The study of shock-driven ejecta production has focused on Richtmyer–Meshkov instability (RMI) growth from geometric features of the material surface. Extensive study of this mechanism under both single- and multiple-shock conditions has found that the ejected mass tends to be closely associated with the shocked surface phase, and its temperature is not dramatically greater than the hydrodynamic shock temperature of the bulk. In this work, we propose and demonstrate a new ejecta production mechanism that can occur under multiple-shock conditions based on the collapse of bubbles near the free surface of the material. This mechanism produces ejected mass that is much greater in quantity than observed in the RMI case. The particles are much hotter than predicted by the shock Hugoniot state, and the ejected mass does not appear to be strongly dependent upon initial surface finish. The ejecta source extends into the material with no clear remaining free surface. We name this mechanism Shallow Bubble Collapse (SBC) and discuss the conditions under which it activates. We demonstrate resolved modeling methods that enable the calculation, design, and study of SBC as a mechanism and perform a series of experiments to compare with the models. Under some multiple-shock conditions, SBC ejection produces ten times more ejected mass than RMI growth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental observations of shock-wave-induced bubble collapse and hot-spot formation in nitromethane liquid explosive

We studied the collapse of individual helium gas bubbles in the homogeneous explosive nitromethane (NM) to investigate effects of hot-spot formation on the detonation process. A bubble was injected into a NM sample, and a shock wave from an explosive detonator compressed the bubble, creating a localized hot spot. We measured shock and detonation wave speeds with optical velocimetry, and we used a high-speed camera to image the shock propagation and the pre- and post-bubble collapse processes. An infrared camera image showed the residual radiance temperature distribution after the bubble collapse, and an optical fiber pyrometer measured the time-resolved thermal radiance. We measured the optical spectra of light emitted from detonating NM without a bubble and from a collapsing bubble in shocked, undetonated NM. We estimated temperatures of the detonation fronts and of the hot spots formed by bubble collapse. To study the incipient detonation process, we performed all bubble collapse experiments at pressures below the threshold for creating a sustained detonation. Where the bubble collapsed, we observed an opaque, thermally emissive region believed to be chemical reaction products. Chemical reactions in NM can be produced with lower shock pressures (~1 GPa) when a helium bubble is present than without a bubble (~10 GPa). We used hydrodynamic modeling to predict shock wave propagation, extent of chemical reaction, and subsequent temperature rise from the collapsing bubble. Simulations using a temperature-dependent Arrhenius burn model gave much better results than reactive burn models that depend only on pressure and density.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Time-stretch spectroscopy for fast infrared absorption spectra of acetylene and hydroxyl radicals during combustion

We have developed a diagnostic that uses time-domain spectroscopy to measure transient infrared absorption spectra in gases. Using a time-stretch Fourier transform approach, we can determine pressure, temperature, and gas concentrations with sub-microsecond time resolution for over two milliseconds. We demonstrate high-resolution (0.015 nm), time-resolved spectral measurements in an acetylene-oxygen gas mixture undergoing combustion. Within a 5 µs period during the reaction, the acetylene line intensities decrease substantially, and new spectra appear that are consistent with the hydroxyl (OH) radical, a common by-product in the combustion, deflagration, and detonation of fuels and explosives. Post-reaction pressures and temperatures were estimated from the OH spectra. The technique measures spectra from 1520 to 1620 nm using fiber optics, photodetectors, and digitizers. No cameras or spectrometers are required.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal interfaces in dynamic compression experiments

Temperature is a difficult thermodynamic variable to measure in dynamic compression experiments. Optical pyrometry is a general-purpose technique for measuring temperature from a radiant surface, but that surface is often the interface between distinct materials with temperatures that vary spatially along the loading direction. This leads to a fundamental problem: how does the measured interface temperature relate to this temperature profile along the compression axis? Numerical analysis of loading history and thermal diffusion at these interfaces shows that seemingly subtle changes in experiment geometry can lead to very different temperature profiles. We compare these results to laboratory temperature measurements of shock-compressed tin.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Anisotropic shock response of single-crystalline β-phase tin shock physics, molecular dynamics, plasticity

Mesoscale simulations of the dynamic response of polycrystalline metals to shockwave compression can provide unique insight in to the nature of the various physical mechanisms responsible for material failure. This approach requires a constitutive description for individual grains and boundaries, including defects such as dislocations, within an explicit representation of the microstructure geometry and evolving deformation fields. Computational models of the single-crystal constituents cannot be unambiguously constrained by traditional measurements of the shock or stress-strain response of polycrystalline metals. Instead, these models require comprehensive measurements of the anisotropic shock response of single crystals for their calibration and validation. We present a coordinated experimental and simulation campaign on the shock response of single-crystalline β-phase tin demonstrating a remarkable anisotropic elastic-plastic response of the metal. This anisotropy will be explained with the help of molecular dynamics simulations that show preferred twinning in one orientation.

36 MATERIALS SCIENCE↗

Simultaneous Raman and pyrometric temperature measurements in shock-wave-compressed toluene

We fielded experiments to compare temperatures measured simultaneously by pyrometry and Raman spectroscopy in toluene shocked to 9 GPa. A 0.5 mm thick toluene sample was compressed between sapphire windows by plate impact from a gas gun. As the shock wave reverberated between the windows, the pressure increased stepwise to about 9 GPa. While the sample was near its peak pressure, we measured the Raman spectrum and determined temperature from the ratio of the Stokes and anti-Stokes intensities. Simultaneously, we measured the sample thermal radiance from the C-H vibration bands that occur between 3.2 and 3.6 μm to determine temperature pyrometrically. The pyrometer used a biased indium antimonide detector paired with a custom transimpedance amplifier, a system capable of temperature measurements as low as about 400 K. The Raman measurements gave a temperature of 530 ± 25 K in the bulk volume of toluene. Pyrometry gave a temperature of 496 + 15/-20 K, which is in reasonable agreement with the Raman measurement. Comparisons of this type are necessary to validate pyrometry as a temperature diagnostic in dynamic experiments.

36 MATERIALS SCIENCE↗

Dynamic reflectance changes in high-purity zirconium when it is shocked from the α to ω phase

Flash lamp-illuminated integrating spheres have been used to measure the dynamic reflectance at the interface between a shocked metal target and a window maintaining the shock stress. In conjunction with radiance measurements, this method was recently used to study the pressure versus temperature phase boundary of the beta phase to body-centered-tetragonal transition of tin at around 13 GPa and, in separate experiments, to show a relationship between the reflectance and the phase fraction. We have used this technique to measure the ratio, R, of the dynamic reflectance relative to the ambient value for a high-purity zirconium sample attached to a sapphire window to study the alpha to omega phase transition. Nine experiments cover the range of stress, σ, from 4 to 16 GPa at six wavelengths from 500 to 1550 nm. The two phases in zirconium differ in volume by <1%, so a phase change between them can be difficult to identify from anomalies in the particle velocity measured on the shock Hugoniot. The phase boundary is believed to cross the Hugoniot around 3 GPa, but dynamically it is observed at much higher stresses >6 GPa. Our results show that the relative reflectance decreases upon initial shock in the alpha state but increases as the material transforms to its omega state. The slope dR/dσ changes the sign around the phase transition. For shocks below 6 GPa, dR/dσ < 0, and for σ above 10 GPa, dR/dσ > 0. In the stress region between 6 and 10 GPa, dR/dσ varies somewhat, perhaps due to the band structure or because the transition is incomplete there. I. INTRODUCTION

74 ATOMIC AND MOLECULAR PHYSICS↗

Spall response of single-crystal copper

We performed a series of systematic spall experiments on single-crystal copper in an effort to determine and isolate the effects of crystal orientation, peak stress, and unloading strain rate on the tensile spall strength. Strain rates ranging from 0.62 to 2.2 × 10 6 s -1 and peak shock stresses in the 5–14 GPa range, with one additional experiment near 50 GPa, were explored as part of this work. Gun-driven impactors, called flyer plates, generated flat top shocks followed by spall. This work highlights the effect of crystal anisotropy on the spall strength by showing that the spall strength decreases in the following order: [100], [110], and [111]. Over the range of stresses and strain rates explored, the spall strength of [100] copper depends strongly on both the strain rate and shock stress. Except at the very highest shock stress, the results for the [100] orientation show linear relationships between the spall strength and both the applied compressive stress and the strain rate. In addition, hydrodynamic computer code simulations of the spall experiments were performed to calculate the relationship between the strain rate near the spall plane in the target and the rate of free surface velocity release during the pullback. As expected, strain rates at the spall plane are much higher than the strain rates estimated from the free surface velocity release rate. We have begun soft recovery experiments and molecular dynamics calculations to understand the unusual recompression observed in the spall signature for [100] crystals.

36 MATERIALS SCIENCE↗

Simultaneous broadband laser ranging and photonic Doppler velocimetry for dynamic compression experiments

A diagnostic was developed to simultaneously measure both the distance and velocity of rapidly moving surfaces in dynamic compression experiments, specifically non-planar experiments where integrating the velocity in one direction does not always give the material position accurately. The diagnostic is constructed mainly from fiber-optic telecommunications components. The distance measurement is based on a technique described by Xia and Zhang [Opt. Express 18, 4118 (2010)], which determines the target distance every 20 ns and is independent of the target speed. We have extended the full range of the diagnostic to several centimeters to allow its use in dynamic experiments, and we multiplexed it with a photonic Doppler velocimetry (PDV) system so that distance and velocity histories can be measured simultaneously using one fiber-optic probe. The diagnostic was demonstrated on a spinning square cylinder to show how integrating a PDV record can give an incorrect surface position and how the ranging diagnostic described here obtains it directly. The diagnostic was also tested on an explosive experiment where copper fragments and surface ejecta were identified in both the distance and velocity signals. We show how the distance measurements complement the velocity data. Potential applications are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Thermal transport in shock wave–compressed solids using pulsed laser heating

A pulsed laser heating method was developed for determining thermal transport properties of solids under shock-wave compression. While the solid is compressed, a laser deposits a known amount of heat onto the sample surface, which is held in the shocked state by a transparent window. The heat from the laser briefly elevates the surface temperature and then diffuses into the interior via one-dimensional heat conduction. The thermal effusivity is determined from the time history of the resulting surface temperature pulse, which is recorded with optical pyrometry. Thermal effusivity is the square root of the product of thermal conductivity and volumetric heat capacity and is the key thermal transport parameter for relating the surface temperature to the interior temperature of the sample in a dynamic compression experiment. Therefore, this method provides information that is needed to determine the thermodynamic state of the interior of a compressed metal sample from a temperature measurement at the surface. The laser heat method was successfully demonstrated on tin that was shock compressed with explosives to a stress and temperature of ∼25 GPa and ∼1300 K. In this state, tin was observed to have a thermal effusivity of close to twice its ambient value. The implications on determining the interior shock wave temperature of tin are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Spall strength and ejecta production of gold under explosively driven shock wave compression

Explosively driven shock wave experiments were conducted to characterize the spall strength and ejecta production of high-purity cast gold samples. The samples were from 0.75 to 1.84 mm thick and 30 mm in diameter. Peak stresses up to 44 GPa in gold were generated using PBX-9501 high explosive. Sample free surface and ejecta velocities were recorded using photonic Doppler velocimetry techniques. Lithium niobate pins were used to quantify the time dependence of the ejecta density and the total ejected mass. An optical framing camera for time-resolved imaging and a single-image x-ray radiograph were used for additional characterization. Free surface velocities exhibited a range of spall strengths from 1.7 to 2.4 GPa (mean: 2.0 ±0.3 GPa). The pullback signals were faint, minimal ringing was observed in the velocity records, and the spall layer continued to decelerate after first pull back. These results suggest finite tensile strength was present for some time after the initial void formation. Ejecta were observed for every sample with a roughened free surface, and the ejecta density increased with increased surface roughness, which was different in every experiment. The total ejected mass is consistent with the missing mass model.

36 MATERIALS SCIENCE↗

Release path temperatures of shock-compressed tin from dynamic reflectance and radiance measurements

Dynamic reflectance and radiance measurements were conducted for tin samples shock compressed to 35 GPa and released to 15 GPa using high explosives. We determined the reflectance of the tin samples glued to lithium fluoride windows using an integrating sphere with an internal xenon flashlamp as an illumination source. The dynamic reflectance (R) was determined at near normal incidence in four spectral bands with coverage in visible and near-infrared spectra. Uncertainties in R/R{sub 0} are <2%, and uncertainties in absolute reflectance are <5%. In complementary experiments, thermal radiance from the tin/glue/lithium fluoride interface was recorded with similar shock stress and spectral coverage as the reflectance measurements. The two sets of experiments were combined to obtain the temperature history of the tin surface with an uncertainty of <2%. The stress at the interface was determined from photonic Doppler velocimetry and combined with the temperatures to obtain temperature-stress release paths for tin. We discuss the relationship between the experimental release paths and release isentropes that begin on the principal shock Hugoniot.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗