Engineering Papers⌕ Search

Engineering topics

LBNL

Publications and source records attributed to LBNL.

At least 19 records

Li+ alumino-silicate ion source development for the Neutralized Drift Compression Experiment (NDCX-II)

To heat targets to electron-volt temperatures for the study of warm dense matter with intense ion beams, low mass ions, such as lithium, have an energy loss peak (dE/dx) at a suitable kinetic energy. The Heavy Ion Fusion Sciences (HIFS) program at Lawrence Berkeley National Laboratory will carry out warm dense matter experiments using Li{sup +} ion beam with energy 1.2-4 MeV in order to achieve uniform heating up to 0.1-1 eV. The accelerator physics design of Neutralized Drift Compression Experiment (NDCX-II) has a pulse length at the ion source of about 0.5 {micro}s. Thus for producing 50 nC of beam charge, the required beam current is about 100 mA. Focusability requires a normalized (edge) emittance {approx}2 {pi}-mm-mrad. Here, lithium aluminosilicate ion sources, of {beta}-eucryptite, are being studied within the scope of NDCX-II construction. Several small (0.64 cm diameter) lithium aluminosilicate ion sources, on 70%-80% porous tungsten substrate, were operated in a pulsed mode. The distance between the source surface and the mid-plane of the extraction electrode (1 cm diameter aperture) was 1.48 cm. The source surface temperature was at 1220 C to 1300 C. A 5-6 {micro}s long beam pulsed was recorded by a Faraday cup (+300 V on the collector plate and -300 V on the suppressor ring). Figure 1 shows measured beam current density (J) vs. V{sup 3/2}. A space-charge limited beam density of {approx}1 mA/cm{sup 2} was measured at 1275 C temperature, after allowing a conditioning time of about {approx} 12 hours. Maximum emission limited beam current density of {ge} 1.8mA/cm{sup 2} was recorded at 1300 C with 10-kV extractions. Figure 2 shows the lifetime of two typical sources with space-charge limited beam current emission at a lower extraction voltage (1.75 kV) and at temperature of 1265 {+-} 7 C. These data demonstrate a constant, space-charge limited beam current for 20-50 hours. The lifetime of a source is determined by the loss of lithium from the alumino-silicate material either as ions or as neutral atoms. Our measurements suggest that for the low duty factor ({approx}10{sup -8}) required for NDCX-II, the lifetime of an emitter depends mostly on the duration that the emitter spends at elevated temperature, that is, at {ge} 1250 C. At this temperature, lithium loss is due mostly to neutral loss (not charged ion extraction). Extension of the lifetime of the source may be possible by lowering the temperature between beam pulses, when the idling time is sufficiently long between shots. The NDCX-II design seeks to operate the ion source at the maximum current density without running into heat management and lifetime problems. In preparation to fabricate a large (10.9 cm in diameter) source for the NDCXII experiment, recently a 7.6 cm diameter source has been fabricated. The method of fabrication of this larger source is similar to that of fabrication of a 6.3mm diameter source, except a longer furnace heating time was used due to mass differences. NDCX-II construction is in progress. Progress of lithium source study for NDCX-II is available in literature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

TIME-DEPENDENT PHASE SPACE MEASUREMENTS OF THE LONGITUDINALLY COMPRESSING BEAM IN NDCX-I

The Neutralized Drift Compression Experiment (NDCXI) generates high intensity ion beams to explore Warm Dense Matter physics. A {approx}150 kV, {approx}500 ns modulating voltage pulse is applied to a {approx}300 kV, 5-10 {mu}s, 25 mA K+ ion beam across a single induction gap. The velocity modulated beam compresses longitudinally during ballistic transport along a space charge neutralizing plasma transport line, resulting in {approx}3A peak current with {approx}2-3 ns pulse durations (FWHM) at the target plane. Transverse final focusing is accomplished with a {approx}8 T, 10 cm long pulsed solenoid magnet. Time-dependent electrostatic focusing in the induction gap, and chromatic aberrations in the final focus optics limit the peak fluenceat the target plane for the compressed beam pulse. We report on time-dependent phase space measurements of the compressed pulse in the ballistic transport beamline, and measurement of the time-dependent radial impulses derived from the interaction of the beam and the induction gap voltage. We present results of start-to-end simulations to benchmark the experiments. Fast correction strategies are discussed with application to both NDCX-I and the soon to be commissioned NDCX-II accelerators.

43 PARTICLE ACCELERATORS↗

Cathode R&D for future light sources

This paper reviews the requirements and current status of cathodes for accelerator applications, and proposes a research and development plan for advancing cathode technology. Accelerator cathodes need to have long operational lifetimes and produce electron beams with a very low emittance. The two principal emission processes to be considered are thermionic and photoemission with the photocathodes being further subdivided into metal and semi-conductors. Field emission cathodes are not included in this analysis. The thermal emittance is derived and the formulas used to compare the various cathode materials. To date, there is no cathode which provides all the requirements needed for the proposed future light sources. Therefore a three part research plan is described to develop cathodes for these future light source applications.

43 PARTICLE ACCELERATORS↗

Presence and spatial distribution of interfacial electronic states in LaMnO{sub 3}-SrMnO{sub 3} superlattices.

We report direct evidence of interfacial states at the onset of O K edge confined to a spatial distance of 1 unit-cell full-width at half maximum at the sharp interfaces between epitaxial films of LaMnO{sub 3} and SrMnO{sub 3} from electron energy-loss spectroscopy (EELS) measurements. The interfacial states are sensitive to interface sharpness; at rough interfaces with interfacial steps of 1-2 unit cells in height, experimental data shows a reduction, or suppression, of the interfacial states. The EELS measurements were performed using a fine electron probe obtained by electron lens aberration correction. By scanning the electron probe across the interface, we are able to map the spatial distribution of the interfacial states across interfaces at high resolution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Real-time observation of valence electron motion.

The superposition of quantum states drives motion on the atomic and subatomic scales, with the energy spacing of the states dictating the speed of the motion. In the case of electrons residing in the outer (valence) shells of atoms and molecules which are separated by electronvolt energies, this means that valence electron motion occurs on a subfemtosecond to few-femtosecond timescale (1 fs = 10{sup -15} s). In the absence of complete measurements, the motion can be characterized in terms of a complex quantity, the density matrix. Here we report an attosecond pump-probe measurement of the density matrix of valence electrons in atomic krypton ions. We generate the ions with a controlled few-cycle laser field and then probe them through the spectrally resolved absorption of an attosecond extreme-ultraviolet pulse, which allows us to observe in real time the subfemtosecond motion of valence electrons over a multifemtosecond time span. We are able to completely characterize the quantum mechanical electron motion and determine its degree of coherence in the specimen of the ensemble. Although the present study uses a simple, prototypical open system, attosecond transient absorption spectroscopy should be applicable to molecules and solid-state materials to reveal the elementary electron motions that control physical, chemical and biological properties and processes.

74 ATOMIC AND MOLECULAR PHYSICS↗

Controlling X-rays With Light

Ultrafast x-ray science is an exciting frontier that promises the visualization of electronic, atomic and molecular dynamics on atomic time and length scales. A largelyunexplored area of ultrafast x-ray science is the use of light to control how x-rays interact with matter. In order to extend control concepts established for long wavelengthprobes to the x-ray regime, the optical control field must drive a coherent electronic response on a timescale comparable to femtosecond core-hole lifetimes. An intense field is required to achieve this rapid response. Here an intense optical control pulse isobserved to efficiently modulate photoelectric absorption for x-rays and to create an ultrafast transparency window. We demonstrate an application of x-ray transparencyrelevant to ultrafast x-ray sources: an all-photonic temporal cross-correlation measurement of a femtosecond x-ray pulse. The ability to control x-ray/matterinteractions with light will create new opportunities at current and next-generation x-ray light sources.

43 PARTICLE ACCELERATORS↗

Ultraintense X-Ray Induced Ionization, Dissociation, and Frustrated Absorption in Molecular Nitrogen

Sequential multiple photoionization of the prototypical molecule N{sub 2} is studied with femtosecond time resolution using the Linac Coherent Light Source (LCLS). A detailed picture of intense x-ray induced ionization and dissociation dynamics is revealed, including a molecular mechanism of frustrated absorption that suppresses the formation of high charge states at short pulse durations. The inverse scaling of the average target charge state with x-ray peak brightness has possible implications for single-pulse imaging applications.

74 ATOMIC AND MOLECULAR PHYSICS↗

Probing interfacial electronic structures in atomic layer LaMnO{sub3} and SrTiO{sub 3} superlattices.

The interfacial electronic structure characterization of a m x (LaMnO{sub 3})/n x (SrTiO{sub 3}) superlattice based on scanning transmission electron microscopy and electron energy loss spectroscopy. Evidence of interfacial band alignment and electron transfer are presented based on the observation of O K edge of individual transition metal and oxygen atomic columns. Electron probe aberration correction was essential for the high spatial resolution mapping of interfacial electronic states.

36 MATERIALS SCIENCE↗

Bilayer splitting and c-axis coupling in bilayer manganites showing colossal magnetoresistance.

By performing angle-resolved photoemission spectroscopy of the bilayer colossal magnetoresistive (CMR) manganite, La{sub 2-2x}Sr{sub 1+2x}Mn{sub 2}O{sub 7}, we provide the complete mapping of the Fermi-level spectral weight topology. Clear and unambiguous bilayer splitting of the in-plane 3d{sub x{sup 2}-y{sup 2}} band, mapped throughout the Brillouin zone, and the full mapping of the 3d{sub 3z{sup 2}-r{sup 2}} band are reported. Peculiar doping and temperature dependencies of these bands imply that as transition from the ferromagnetic metallic phase approaches, either as a function of doping or temperature, coherence along the c-axis between planes within the bilayer is lost, resulting in reduced interplane coupling. These results suggest that interplane coupling plays a large role in the CMR transition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Longitudinal Density Tailoring for the Enhancement of Electron Beams in theCapillary-discharge Laser-guidedWakefield Accelerator

Density perturbations in a hydrogen-filled capillary discharge waveguide have been used to control the injection of electrons into a laser wakefield. This has allowed injection and acceleration in channels of lower density than previously possible, and the production of relativistic electron beams with improved stability. For parameters of optimum stability, the mean bunch energy was 300MeV +- 7 MeV rms, with divergence 1.3 mrad +- 0:1 mrad rms and pointing stability 0.8 mrad rms.

43 PARTICLE ACCELERATORS↗

Imaging of lateral spin valves with soft x-ray microscopy

We investigated Co/Cu lateral spin valves by means of high-resolution transmission soft x-ray microscopy with magnetic contrast that utilizes x-ray magnetic circular dichroism (XMCD). No magnetic XMCD contrast was observed at the Cu L{sub 3} absorption edge, which should directly image the spin accumulation in Cu. Although electrical transport measurements in a non-local geometry clearly detected the spin accumulation in Cu, which remained unchanged during illumination with circular polarized x-rays at the Co and Cu L{sub 3} absorption edges.

36 MATERIALS SCIENCE↗

Performance tests of large area position-sensitive planar germanium detectors with conventional and amorphous contacts.

Large area position-sensitive planar germanium wafers are increasingly being used for a variety of gamma-ray imaging and tracking tasks. Position sensitivity can be achieved through measuring charge collected on orthogonal strip electrodes, and by digital pulse shape analysis. However, the development of this detector technology has been slow, and criteria to measure improved performance have not been well established. We have studied 93 and 88 mm square segmented detectors of 20 mm thickness made with conventional boron and lithium electrodes, and two 100 mm circular segmented detectors of 14 mm thickness with amorphous germanium contacts. We have compared these detectors with a planar detector of 15 mm thickness. Conventional energy resolution tests of individual strips are insufficient to fully categorize the performance of the position sensitive detectors. We propose some basic tests which can rapidly quantify any segmented detector characteristics, and show potential inadequacies which become important when imaging or tracking is attempted.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

The development and relaxation of growth strains in thermally grown Al{sub 2}O{sub 3} scales.

The strains in alumina thin films growing on high-temperature alloys at 1,000-1,100 C and during cooling have been successfully measured in-situ using a novel x-ray technique, exploiting synchrotron radiation at the Advanced Photon Source at Argonne National Laboratory. This paper summarizes results obtained from model alloys, with or without the presence of a reactive element, such as Zr, Hf, and Y, to show the importance of the dynamic nature of the stress evolution process and the effects of alloy composition on the generation and relaxation of these stresses.

43 PARTICLE ACCELERATORS↗

Spin-charge-lattice coupling through resonant multimagnon excitations in multiferroic BiFeO{sub 3}.

Spin-charge-lattice coupling mediated by multimagnon processes is demonstrated in multiferroic BiFeO{sub 3}. Experimental evidence of two- and three-magnon excitations as well as multimagnon coupling at electronic energy scales and high temperatures are reported. Temperature dependent Raman experiments show up to five resonant enhancements of the two-magnon excitation below the Neel temperature. These are shown to be collective interactions between on-site Fe d-d electronic resonance, phonons, and multimagnons.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Magnon sidebands and spin-charge coupling in bismuth ferrite probed by nonlinear optical spectroscopy.

The interplay between spin waves (magnons) and electronic structure in materials leads to the creation of additional bands associated with electronic energy levels which are called magnon sidebands. The large difference in the energy scales between magnons (meV) and electronic levels (eV) makes this direct interaction weak and hence makes magnon sidebands difficult to probe. Linear light absorption and scattering techniques at low temperatures are traditionally used to probe these sidebands. Here we show that optical second-harmonic generation, as the lowest-order nonlinear process, can successfully probe the magnon sidebands at room temperature and up to 723 K in bismuth ferrite, associated with large wave vector multimagnon excitations which linear absorption studies are able to resolve only under high magnetic fields and low temperatures. Polarized light studies and temperature dependence of these sidebands reveal a spin-charge coupling interaction of the type P{sub s}L{sup 2} between the spontaneous polarization (P{sub s}) and antiferromagnetic order parameter, L in bismuth ferrite, that persists with short-range correlation well into the paramagnetic phase up to high temperatures. These observations suggest a broader opportunity to probe the collective spin-charge-lattice interactions in a wide range of material systems at high temperatures and electronic energy scales using nonlinear optics.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Local structure of La{sub 1-x}Sr{sub x}CoO{sub 3} determined from EXAFS and neutron PDF studies.

The combined local structure techniques, extended x-ray absorption fine structure and neutron pair distribution function analysis, have been used for temperatures 4 {le} T {le} 330 K to rule out a large Jahn-Teller (JT) distortion of the Co-O bond in La{sub 1-x}Sr{sub x}CoO{sub 3} for a significant fraction of Co sites (x {le} 0.35), indicating few, if any, JT-active, singly occupied e{sub g} Co sites exist.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A 3-cell deflecting rf cavity for emittance exchange experiment at ANL.

An RF deflecting structure has been designed and fabricated for a transverse-to-longitudinal emittance exchange experiment at Argonne National Laboratory (ANL) [Y.-E. Sun, et al., Design study of a transverse-to-longitudinal emittance exchange proof-of-principle experiment, in: Proceedings of PAC-2007, Albuquerque, NM, USA, 2007, pp. 3441-3443]. The structure is a 1300 MHz normal conducting RF cavity consisting of three cells operating in a dipole (TM{sub 110}-like) mode. As high as 3.4 MV deflecting voltage is required for the experiment. In this paper, we present detailed RF design of the cavity, particle tracking simulations in the cavity and low power RF measurement results in comparison with numerical simulations. The cavity cell geometries (gaps in particular) are optimized to giving a zero orbit offset for particles crossing the cavity with zero-phase.

43 PARTICLE ACCELERATORS↗

CIFTS : A coordinated infrastructure for fault-tolerant systems.

In the next few years SciDAC applications will utilize petascale systems with tens to hundreds of thousands of processors, hundreds of I/O nodes, and thousands of disks. This leap of two orders of magnitude in scale from today's typical systems is causing a critical gap in fault management of these systems. The fault management issues for these emerging systems are well beyond the scope of today's common infrastructure and practice. Currently, systems software components for large-scale machines remain largely independent in their fault awareness and notification strategies. Faults can arise not just from the hardware but also from the OS, middleware, libraries, and application levels. Petascale applications that are evolving to utilize these platforms face many new challenges. With the CIFTS initiative, we aim to provide a coordinated infrastructure that will enable Fault Tolerant Systems to adapt to faults occuring in the operating environment in a holistic manner. Our approach will be to design a reference implementation of a fault awareness and notification backplane to provide common uniform event handling and notification mechanisms for fault-aware libraries and middleware; create an interface specification that allows libraries, run- time systems, and applications to connect to and use the fault-tolerance backplane; and extend key libraries and applications to validate the interface choices and to form the critical mass necessary for adoption in the community.

99 GENERAL AND MISCELLANEOUS↗