Engineering Papers⌕ Search

Engineering topics

Kyu, Thein

Publications and source records attributed to Kyu, Thein.

Solid-state polymer magnesium supercapacitor

Here, the present article focuses on the development of a highly ion-conductive, solvent-free, solid-state polymer electrolyte membrane (PEM) via photopolymerization of polyethylene glycol diacrylate (PEGDA) network from its homogeneous melt mixtures containing succinonitrile (SCN) plasticizer and magnesium bis(trifluoromethane sulfonyl) imide Mg(TFSI) 2 salt. The above solid-state Mg-PEM exhibits a Helmholtz electric double-layer capacitor (EDLC) behavior in its supercapacitive symmetric carbonaceous electrode configuration. The electrochemical stability for this PEM membrane (20/40/40 PEGDA/SCN/Mg (TFSI) 2 ) was found to be approximately 3 V from linear sweep voltammetry with a specific capacitance of about 44 F/g from cyclic voltammetry and an energy density of approximately 17 Wh/kg in the 0–2 V range from the constant current density (CCD) experiment. Of particular interest is its excellent capacity retention of over 11,200 cycles, thus tested with the Coulombic efficiency of over 87%. Moreover, the energy density after extensive cycling for 11,200 has increased to approximately 56 Wh/kg at 10 mV/s in the potential range of 0–3 V relative to 17 Wh/kg in the potential range of 0–2 V at the same scan rate, attesting the excellent electrochemical stability and long life of the present Mg-PEM supercapacitor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effects of photointensity gradient on directional crystal growth in blends of crystalline polymer and photoreactive monomer undergoing photopolymerization-induced phase transformation

Effects of light intensity gradient on development of intricate hierarchical morphology of semicrystalline polyethylene oxide (PEO) and photoreactive diacrylate (DA) blends undergoing photopolymerization-induced crystallization have been demonstrated experimentally and theoretically. The melting temperature of PEO was found to decline upon addition of DA monomer. A solid-liquid phase diagram has been established by self-consistently solving the combined phase field free energy of crystal solidification and Flory-Huggins (FH) free energy of liquid-liquid demixing. Dynamic calculations were performed using time-dependent Ginzburg-Landau (model C) equations by incorporating the combined phase field and FH free energy densities coupled with the photopolymerization kinetics. The spatiotemporal development of gradient morphology was computed under various intensity gradient profiles including linear, cylindrical, and Gaussian profiles. The observed seaweed or dense lamellar branching morphology of the PEO/DA blend is strikingly similar to the directionally grown interface structures observed in metals driven by external thermal gradients.

36 MATERIALS SCIENCE↗

Photopolymerization-induced crystallization and phase separation in poly(ethylene oxide)/triacrylate blends

The present article describes experimental and theoretical investigations of miscibility and crystallization behavior of blends of poly(ethylene oxide) (PEO) and triacrylate monomer (TA) using differential scanning calorimetry and optical microscopy. The PEO/TA blends manifested a single T{sub g} varying systematically with composition suggestive of a miscible character in their amorphous states. Moreover, there occurs melting point depression of PEO crystals with increasing TA. A phase diagram was subsequently established that exhibited a solid+liquid coexistence region bound by the liquidus and solidus lines, followed by an upper critical solution temperature (UCST) at a lower temperature. The emerging phase morphology was investigated to verify the coexistence regions. Upon photopolymerization in the isotropic melt above the melting point depression curve, both the UCST and the melting temperatures move upward and eventually surpass the reaction temperature, resulting in phase separation as well as crystallization of PEO driven by the changing supercooling, i.e., the thermodynamic driving force. Of particular interest is the interplay between photopolymerization-induced phase separation and crystallization, which eventually determines the final phase morphology of the PEO/TA blend such as crystalline lamellae, sheaf, or spherulites in isotropic liquid, phase separated domains, and viscous fingering liquids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Experiments and Models for Polymeric Microsphere Foams

The current project was performed under the direction of Dr. Byron Pipes as its lead investigator from January 2001 to August 2004. With the permission of the NASA, the project was transferred to Dr. Thein Kyu as the principle investigator for the period of September 2004 - June 2005. There were two major thrust areas in the original proposal; (1) experimental characterization and kinematics of foam structure formation and (2) determination of the mechanical, physical, and thermal properties, although these thrust areas were further sub- divided into 7 tasks. The present project has been directed primarily to elucidate kinematics of micro-foam formation (tasks 1 and 3) and to characterize micro-foam structures, since the control of the micro-structure of these foams is of paramount importance in determining their physical, mechanical and thermal properties. The first thrust area was accomplished in a timely manner; however, the second thrust area of foam properties (tasks 2,4-7) has yet to be completed because the area of kinematics of foam structure formation turned out to be extremely complex and thus consumed more time than what have been anticipated. As will be reported in what follows, the present studies have greatly enhances the in-depth understanding of mechanisms and kinematics of the micro-foam formation from solid powders. However, in order to implement all objectives of the second thrust areas regarding investigations of mechanical, physical, and thermal properties and establishment of the correlation of structure - properties of the foams, the project needs additional time and resources. The technical highlights of the accomplishment are summarized as follows. The present study represents a first approach to understanding the complexities that act together in the powder foaming process to achieve the successful inflation of polyimide microstructures. This type of study is novel as no prior work had dissected the fundamentals that govern the inflation process in this type of systems. The systematic approach to each of the different phenomena (i.e. morphological, diffusive, kinetic and dynamic) brings into context each of them in a way that allows separate understanding and analysis. Of the different phenomena studied, probably the one that gives a higher level of control over the inflation process has been shown to be the morphological aspects of the precursor particles. It is a major contribution of the present work to isolate and identify this phenomenon and highlight the features that with careful control during the synthesis of the precursor material can lead to a highly optimized and specialized final product (neat foam or microstructure). Some of these accomplishments have been presented in various national meetings and some of which are either published in refereed journals or still in various stages of publications. One of the presentations was selected for "Best of ANTEC 2004" Online Presentation Series of the Society of Plastics Engineers (SPE) (September 2004)

Pipes, R. Byrona↗