Engineering Papers⌕ Search

Engineering topics

Kumar, M

Publications and source records attributed to Kumar, M.

35 records · Page 2

Experimental tests of stereological estimates of grain boundary populations

We present experimental validation of a method for estimating three-dimensional (3-D) relative numerical populations of grain boundaries from measurements of individual two-dimensional (2-D) cross-sections. Such numerical populations are relevant to network topology and the modeling of intergranular failure modes in grain boundary engineered materials, and are distinct from geometrical population measures such as area per volume. We examine 3-D reconstructions of stainless steel and copper, with varying populations of twin-related boundaries, generated by serial-section electron backscatter diffraction and high-energy X-ray diffraction microscopy. We show that 2-D length fractions, 2-D number fractions and 3-D number fractions are all distinct quantities when grain boundary type is correlated with grain boundary size. We also demonstrate that the last quantity may be reliably inferred from the first two, provided the experimental spatial resolution is much finer than the grain size, eliminating the need to use 3-D experimental methods to access at least some information about 3-D network properties. Many of the {Sigma}3 boundaries are extremely complex, with highly re-entrant shapes that can intersect a sample plane many times, giving a false impression of multiple separate boundaries.

36 MATERIALS SCIENCE↗

PLASTIC BEHAVIOR OF POLYCRYSTALLINE TANTALUM IN THE 5 x 10^7/s REGIME

The goal of this experiment is to investigate the plastic response of Tantalum to dynamic loading at high strain rates. The samples used were derived from high purity rolled plate, polished down to thicknesses in the range 25-100 {micro}m. Dynamic loading was applied by direct laser ablation of the sample, with pulses up to 10 ns long, at the Jupiter Laser Facility. The elastic-plastic wave structure was measured using two line VISAR systems of different sensitivity, and strain rates were inferred from the rise time of the waves. The elastic wave amplitudes indicated flow stresses between 2 and 3 GPa, depending on the sample thickness. Samples were recovered for post-shot metallographic analysis.

36 MATERIALS SCIENCE↗

High-order harmonic generation in carbon-nanotube-containing plasma plumes

High-order harmonic generation (HHG) in carbon-nanotube (CNT)-containing plasma plumes has been demonstrated. Various targets were ablated to produce the plasma plumes containing nanotubes for the HHG in these media. Harmonics up to the 29th order were generated. Odd and even harmonics were generated using a two-color pump. The integrity of CNTs within the plasma plume, indicating nanotubes as the source of high-order harmonics, was confirmed by structural studies of plasma debris.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fourth-order harmonic generation during parametric four-wave mixing in the filaments in ambient air

We propose a simplified scheme for efficient 200-nm pulse generation in isotropic medium using 800-nm radiation. The observation and optimization of the fourth-order harmonic generation during two-color filamentation in air are reported. This parametric process is based on four-wave mixing of the fundamental and the second-order harmonic radiation of the Ti:sapphire laser. A systematic study of the influence of the laser intensity, the polarization, the chirp, and the pulse duration on the fourth-order harmonic output from the filaments has been carried out. The fourth-order harmonic conversion efficiency was estimated to be of the order of 10{sup -4}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

PERFORMANCE STUDY OF LIQUID NITROGEN THERMO-SIPHON COOLING LOOP

A RF-superconducting linear accelerator (LINAC) booster for the existing 15 UD Pelletron accelerator is presently under construction at Inter-University Accelerator Centre in New Delhi, India. The LINAC will make use of superconducting niobium quarter-wave resonators (QWR) as the accelerating element, and will consist of three accelerating cryomodules. A gravity-assisted (thermo-siphon) flow scheme with liquid nitrogen has been proposed to cool the thermal radiation shields of the LINAC cryomodules. A small test rig of the thermo-siphon loop has been developed to simulate and investigate the chosen aspects of the proposed configuration. The experimental work has been focused on the thermal performances of the specially designed copper clamps and optimization of the system engineering parameters. The paper presents the results of the thermo-siphon measurements and the qualitative description of the investigated phenomena.

42 ENGINEERING↗

LLNL compiled first pages ordered by ascending B&R code

We aim to develop a fundamental understanding of materials dynamics (from {micro}s to ns) in systems where the required combination of spatial and temporal resolution can only be reached by the dynamic transmission electron microscope (DTEM). In this regime, the DTEM is capable of studying complex transient phenomena with several orders of magnitude time resolution advantage over any existing in-situ TEM. Using the unique in situ capabilities and the nanosecond time resolution of the DTEM, we seek to study complex transient phenomena associated with rapid processes in materials, such as active sites on nanoscale catalysts and the atomic level mechanisms and microstructural features for nucleation and growth associated with phase transformations in materials, specifically in martensite formation and crystallization reactions from the amorphous phase. We also will study the transient phase evolution in rapid solid-state reactions, such as those occurring in reactive multilayer foils (RMLF). Program Impact: The LLNL DTEM possesses unique capabilities for capturing time resolved images and diffraction patterns of rapidly evolving materials microstructure under strongly driven conditions. No other instrument in the world can capture images with <10 nm spatial resolution of interesting irreversible materials processes such as phase transformations, plasticity, or morphology changes with 15 ns time resolution. The development of this innovative capability requires the continuing collaboration of laser scientists, electron microscopists, and materials scientists experienced in time resolved observations of materials that exist with particularly relevant backgrounds at LLNL. The research team has made observations of materials processes that are possible by no other method, such as the rapid crystallization of thin film NiTi that identified a change in mechanism at high heating rates as compared to isothermal anneals through changes in nucleation and growth rates of the crystalline phase. The project is designed to reveal these fundamental processes and mechanisms in rapid microstructure evolution that form the foundation of understanding that is an integral part of the DOE-BES mission.

36 MATERIALS SCIENCE↗

FREE SURFACE VELOCIMETRY CORRECTIONS FOR LOW PRESSURE SHOCKS

We consider how to interpret measured free surface velocities to estimate what a relatively weak shock (with an elastic-plastic two-wave structure, approx5-30 GPa) would have looked like in an infinite sample. Hysteresis and nonlinear wave interactions introduce effects (inexact velocity doubling and the delay, partial reflection, and reverberation of waves) whose magnitudes can be estimated with simple models. We argue, and demonstrate in a simulated test case, that these estimates can eliminate most of the systematic error introduced by the free surface during loading.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Shock Hugoniot of Single Crystal Copper

The shock Hugoniot of single crystal copper is reported for stresses below 66 GPa. Symmetric impact experiments were used to measure the Hugoniots of three different crystal orientations of copper, [100], [110], [111]. The photonic doppler velocimetry (PDV) diagnostic was adapted into a very high precision time of arrival detector for these experiments. The measured Hugoniots along all three crystal directions were nearly identical to the experimental Hugoniot for polycrystalline Cu. The predicted orientation dependence of the Hugoniot from MD calculations was not observed. At the lowest stresses, the sound speed in Cu was extracted from the PDV data. The measured sound speeds are in agreement with values calculated from the elastic constants for Cu.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Flow Stress of V, Mo, Ta, and W on Nanosecond Time Scales

The mechanisms and kinetics of plastic flow in body-centered cubic materials are of current interest in the development of fundamental theories of dynamic strength, applicable at high strain rates such as are found in high explosive and laser loading. We have performed dynamic loading experiments with the Janus and Trident lasers, using tailored pulse shapes to induce shock or ramp loading. The response of the sample was investigated through the surface velocity history, and in some cases with in-situ x-ray diffraction. The velocity histories exhibited clear elastic waves, from which the flow stress was deduced and compared with the elastic strain as determined by diffraction. We compare the deduced flow stress with models calibrated to samples millimeters thick, and to theoretical studies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Shock Driven Twinning in Tantalum Single Crystals

Recovery based observations of high pressure material behavior generated under high explosively driven flyer based loading conditions are reported. Two shock pressures, 25, and 55 GPa and four orientations {l_brace}(100), (110), (111), (123){r_brace} were considered. Recovered material was characterized using electron backscatter diffraction along with a limited amount of transmission electron microscopy to assess the occurrence of twinning under each test condition. Material recovered from 25 GPa had a very small fraction of twinning for the (100), (110), and (111) oriented crystals while a more noticeable fraction of the (123) oriented crystal was twinned. Material recovered from 55 GPa showed little twinning for (100) orientation slightly more for the (111) orientation and a large area fraction for the (123) orientation. The EBSD and TEM observations of the underlying deformation substructure are rationalized by comparing with previous static and dynamic results.

36 MATERIALS SCIENCE↗

SHOCKLESS LOADING WITH RECOVERY FOR CHARACTERIZATION OF MATERIAL RESPONSE

A new recovery based method for investigating material response to non-Hugoniot loading paths is described. The work makes use of a laser generated plasma piston that produces ramped loading at high strain rates (> {approx} 10{sup 7}/s). Large sample sizes are utilized to prevent reflected wave interactions. The overall deformation path is characterized by two transients: one at very high strain rate on the 5-10 nanosecond time scale and one at a lower strain rate occurring over a 1-2 microsecond timescale. It was found that a sufficiently large region of material experiences shockless loading conditions such that recovery based characterization is feasible. The presence of two strain transients makes the method more applicable to comparative assessments between shockless and shock loading conditions.

36 MATERIALS SCIENCE↗

Assessment of reduction behavior of hematite iron ore pellets in coal fines for application in sponge ironmaking

Studies on isothermal reduction kinetics (with F grade coal) in fired pellets of hematite iron ores, procured from four different mines of Orissa, were carried out in the temperature range of 850-1000C to provide information for the Indian sponge iron plants. The rate of reduction in all the fired iron ore pellets increased markedly with a rise of temperature up to 950C, and thereafter it decreased at 1000C. The rate was more intense in the first 30 minutes. All iron ores exhibited almost complete reduction in their pellets at temperatures of 900 and 950C in 2 hours' heating time duration, and the final product morphologies consisted of prominent cracks. The kinetic model equation 1-(1-a){sup 1/3}=kt was found to fit best to the experimental data, and the values of apparent activation energy were evaluated. Reductions of D. R. Pattnaik and M. G. Mohanty iron ore pellets were characterized by higher activation energies (183 and 150 kJ mol{sup -1}), indicating carbon gasification reaction to be the rate-controlling step. The results established lower values of activation energy (83 and 84 kJ mol{sup -1}) for the reduction of G. M. OMC Ltd. and Sakaruddin iron ore pellets, proposing their overall rates to be controlled by indirect reduction reactions.

01 COAL, LIGNITE, AND PEAT↗

Studies on the reduction kinetics of hematite iron ore pellets with noncoking coals for sponge iron plants

In the present investigation, fired pellets were made by mixing hematite iron ore fines of -100, -16+18, and -8+10 mesh size in different ratios and studies on their reduction kinetics in Lakhanpur, Orient OC-2 and Belpahar coals were carried out at temperatures ranging from 850{sup o}C to 1000{sup o}C with a view toward promoting the massive utilization of fines in ironmaking. The rate of reduction in all the fired iron ore pellets increased markedly with an increase in temperature up to 1000{sup o}C, and it was more intense in the first 30min. The values of activation energy, calculated from integral and differential approaches, for the reduction of fired pellets (prepared from iron ore fines of -100 mesh size) in coals were found to be in the range 131-148 and 130-181 kJ mol{sup -1} (for =0.2 to 0.8), indicating the process is controlled by a carbon gasification reaction. The addition of selected larger size particles in the matrix of -100 mesh size fines up to the extent studied decreased the activation energy and slightly increased the reduction rates of resultant fired pellets. In comparison to coal, the reduction of fired pellets in char was characterized by significantly lower reduction rates and higher activation energy.

01 COAL, LIGNITE, AND PEAT↗

Repeat Sequence Proteins as Matrices for Nanocomposites

Recombinant protein-inorganic nanocomposites comprised of exfoliated Na+ montmorillonite (MMT) in a recombinant protein matrix based on silk-like and elastin-like amino acid motifs (silk elastin-like protein (SELP)) were formed via a solution blending process. Charged residues along the protein backbone are shown to dominate long-range interactions, whereas the SELP repeat sequence leads to local protein/MMT compatibility. Up to a 50% increase in room temperature modulus and a comparable decrease in high temperature coefficient of thermal expansion occur for cast films containing 2-10 wt.% MMT.

59 BASIC BIOLOGICAL SCIENCES↗

Present State of Electron Backscatter Diffraction and Prospective Developments

Electron backscatter diffraction (EBSD), when employed as an additional characterization technique to a scanning electron microscope (SEM), enables individual grain orientations, local texture, point-to-point orientation correlations, and phase identification and distributions to be determined routinely on the surfaces of bulk polycrystals. The application has experienced rapid acceptance in metallurgical, materials, and geophysical laboratories within the past decade (Schwartz et al. 2000) due to the wide availability of SEMs, the ease of sample preparation from the bulk, the high speed of data acquisition, and the access to complementary information about the microstructure on a submicron scale. From the same specimen area, surface structure and morphology of the microstructure are characterized in great detail by the relief and orientation contrast in secondary and backscatter electron images, element distributions are accessed by energy dispersive spectroscopy (EDS), wavelength dispersive spectroscopy (WDS), or cathodoluminescence analysis, and the orientations of single grains and phases can now be determined, as a complement, by EBSD.

36 MATERIALS SCIENCE↗