Engineering topics

Kumar, K. S.

Publications and source records attributed to Kumar, K. S..

44 records · Page 3

NASA NTRS1991

1200 and 1300 K slow plastic compression properties of Ni-50Al composites

XD synthesis, powder blending, and hot pressing techniques have been utilized to produce NiAl composites containing 4, 7.5, 15, and 25 vol pct alumina whiskers and hybrid composite materials with 15 vol pct Al2O3 + 10 or 20 vol pct, nominally 1 micron TiB2 particles. The resistance to slow plastic flow was determined at 1200 and 1300 K via compression testing in air under constant velocity conditions. The stress-strain behavior of the intermetallic composites depended on the fraction of second phases where the 4 and 7.5 percent Al2O3 materials flowed at a nominally constant stress after about 2 percent deformation, while all the other composites exhibited diffuse yielding followed by strain softening. The flow stress-strain rate properties increased with volume fraction of Al2O3 whiskers except for the 4 and 7.5 percent materials, which had similar strengths. The hybrid composite NiAl + 15Al2O3 + 10TiB2 was substantially stronger than the materials simply containing alumina. Deformation in these composites can be described by the Kelly and Street model of creep in perfectly bonded, rigid, discontinuous fiber materials.

Whittenberger, J. D.↗

NASA NTRS1990

Compression behavior of the forged Ll2 compounds Al67Ti25Cr8 and Al66Ti25Mn9

The paper presents the findings of a compression study as a function of temperature from cryogenic temperatures to 1373 K at a strain rate of about 0.0001/s on forged Al67Ti25Cr8 and Al66Ti25Mn9 compounds. The creep response of these alloys is analyzed at strain rates varying from 2 x 10 to the -4th to 2 x 10 to the -7th /s at 1000 K and 1100 K. It is shown that as-cast microstructures for both compounds are dendritic, while both intermetallics forged very well with no edge cracking, with the microstructures appearing fully recrystallized. True comprehensive stress-strain diagrams determined at 1100 K as a function of nominal strain rate reveal a range of behaviors in both materials.

Brown, S. A.↗

NASA NTRS1990

High-temperature slow-strain-rate compression studies on CoAl-TiB2 composites

Results are presented of compressive deformation tests performed on particulate-reinforced CoAl-TiB2 composites in the temperature range 1100-1300 K. Hot-pressed and postdeformation microstructures were characterized by TEM and by optical microscopy. It was found that the addition of TiB2 particles improves the deformation resistance of the matrix, due to dislocation-particle interactions.

Mannan, S. K.↗

NASA NTRS1990

Effect of a prior stretch on the aging response of an Al-Cu-Li-Ag-Mg-Zr alloy

The effect of a prior stretching of an aluminum alloy Al-5.3Cu-1.4Li-0.4Ag-0.4Mg-0.17Zr (in wt pct) on the microstructure that develops during aging of this alloy was investigated by comparing TEM and SAD observations and hardness curves with results for the unstretched alloy. The results suggest that stretching introduces a significant number of dislocations which may act as vacanacy sinks by sweeping vacancies away and thereby decreasing the vacancy concentration available for influencing the natural aging response. In the stretched and near-peak aged condition, a fine homogeneous distribution of T1, theta-prime, and S-prime phases were observed in an alpha solid solution matrix. Upon overaging, virtually all of the theta-prime and most of the S-prime phases were found to dissolve, leaving behind a microstructure of T1 precipitates.

Kumar, K. S.↗

NASA NTRS1990

1300 K compressive properties of several dispersion strengthened NiAl materials

To examine the potential of rapid solidification technology (RST) as a means to fabricate dispersion-strengthened aluminides, cylindrical compression samples were machined from the gauge section of their tensile specimens and tested in air at 1300 K. While microscopy indicates that RST can produce fine dispersions of TiB2, TiC and HfC in a NiAl matrix, the mechanical property data reveal that only HfC successfully strengthens the intermetallic matrix. The high stress exponents (above 10) and/or independence of strain rate on stress for NiAl-HfC materials suggest elevated temperature mechanical behavior similar to that found in oxide dispersion-strengthened alloys. Furthermore, an apparent example of departure side pinning has been observed, and as such, it is indicative of a threshold stress for creep.

Whittenberger, J. Daniel↗

NASA NTRS1989

1100 to 1300 K slow plastic compression properties of Ni-38.5Al composites

Compressive properties of Ni-38.5Al (in at. pct) composites containing 4, 7.5, and 15 vol pct Al2O3 whiskers or 20 vol pct TiB2 particles were investigated in samples compacted to full density by vacuum hot pressing at 20.7 MPa and 1725 K, followed by HIP at 207 MPa and 1725 K. Constant-velocity compression tests were conducted in air at 1100, 1200, and 1300 K to 8 percent strain. It was found that the elevated-temperature compressive properties of Ni-38.5Al+Al2O3 whisker composites were only marginally better than those of the matrix, and that the composite containing 20 vol pct TiB2 particles was only slightly stronger than unreinforced Ni-38.5Al.

Whittenberger, J. Daniel↗

NASA NTRS1989

1200 to 1400 K slow strain rate compressive behavior of small grain size NiAl/Ni2AlTi alloys and NiAl/Ni2AlTi-TiB2 composites

In order to impart ductility into NiAl-Ni2AlTi alloys, small grain size single (Ni-45Al-5Ti) and two (Ni-40Al-10Ti) phase intermetallics are fabricated by a process which yields fine microstructures in NiAl. The results of a study of elevated temperature compressive properties of two small grain size NiAl-Ni2AlTi alloys are then described. In addition, the behavior of the Ti-modified nickel aluminides with 20 vol pct TiB2 particles of approximately 1 micron in diameter is also investigated, since these compositions have the potential for being the matrix material in high temperature particulate-strengthened composites.

Whittenberger, J. Daniel↗

NASA NTRS1989

1200 to 1400 K slow strain rate compressive properties of NiAl/Ni2AlTi-base materials

An attempt to apply the Martin Marietta Corporation's XD technology to the fabrication of NiAl-Ni2AlTi materials with improved creep properties is presented. Composite materials, containing from 0 to 30 vol pct of nominally 1-micron-diameter TiB2 particles in the intermetallic matrix have been produced by the XD process and compacted by hot pressing. Such composites demonstrated significant strength increases, approaching 3-fold for the 20 vol pct materials, in comparison to the unreinforced aluminide. This behavior was accomplished without deleterious side effects as the grain boundaries and particle-matrix interfaces were intact after compressive deformation to 10 percent or more strain. Typical true compressive stress-strain diagrams for materials tested in air between 1200 and 1400 K at approximate strain rates of 1.7 x 10 to the -6th/sec are presented.

Whittenberger, J. Daniel↗