Engineering Papers⌕ Search

Engineering topics

Kukkadapu, Goutham

Publications and source records attributed to Kukkadapu, Goutham.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

An experimental and chemical kinetic modeling study of 4-butoxyheptane combustion

Here, the combustion kinetics of a novel oxygenated bioblendstock for diesel, 4-butoxyheptane (4-BH), was investigated experimentally using a flow reactor and a heated, high-pressure shock tube. The flow reactor experiments employed oxygen as the oxidizer and helium as the diluent with oxidation conducted at atmospheric pressure and 10 bar for temperatures from 400 to 1000 K at 20-K intervals. The fuel, oxidizer, and diluent flow rates were varied at different temperatures to maintain a constant initial fuel mole fraction of 1000 ppm, with stoichiometric equivalence ratio, and a residence time of 2.0 s. The reacted gas was fed to two separate GC systems that could qualitatively and quantitatively detect product species. Additionally, real fuel-air ignition delay time (IDT) data were collected using a heated, high-pressure shock-tube facility. Fuel lean (φ = 0.5) and stoichiometric (φ = 1.0) mixtures were investigated at 10 atm as well as at 30 atm for the fuel lean case for temperatures between 847 and 1259 K. A detailed chemical kinetics mechanism was developed to model the product distribution from the flow reactor and IDTs from the shock tube. The proposed model was able to predict the double NTC behavior in flow reactor experiments reasonably well. Model predictions at low temperatures were observed to be highly sensitive to the rate constants of ketohydroperoxide (KHP) decomposition in the case of the OOH group in α position which were modeled based on existing literature studies on ethers. It was noted that in the absence of theoretical or experimental studies, the rate constants for KHP decomposition used in the literature were empirically set. Additional studies are required to address the gap in model prediction obtained in this study and to reduce the uncertainty in kinetics models for ether oxidation. Predicted product concentrations and IDTs showed some quantitative agreement with experimental data, but the overall reactivity of the IDTs is underpredicted. Additionally, significant deviation is observed for the IDT results at 10 atm for the stoichiometric case with minor deviations for the other cases. The reaction pathways to the missing products were then further analyzed theoretically through quantum-mechanical calculations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Autoignition of cyclohexane at low-to-intermediate temperatures: Rapid compression machine experiments and improved comprehensive chemical kinetic model

Cycloalkanes are an important class of hydrocarbons found in conventional and alternative transportation fuels. Being one of the simplest practical cycloalkanes, cyclohexane is often used as a surrogate in studies to understand the oxidation, ignition, and sooting characteristics of cycloalkanes more broadly. Although cyclohexane has been extensively studied, very limited datasets for cyclohexane oxidation at low-to-intermediate temperatures are available in the literature. Moreover, the literature autoignition data from rapid compression machines (RCMs) did not provide information on volume histories or experimental heat transfer characteristics which can significantly impact model predictions, thereby hindering the detailed validation of chemical kinetic models. It has also been observed that the cyclohexane kinetic models developed so far are not able to predict the literature data across a wide range of operating and mixture conditions. Hence, further studies are recommended to understand and improve model predictions for cyclohexane oxidation. In this study, RCM experiments were conducted using cyclohexane/air mixtures at varying compressed pressures (P C =15, 20, and 30 bar), equivalence ratios (ϕ=0.5, 1.0, and 2.0), and compressed temperatures (T C =670–960 K). The current RCM results of cyclohexane were found to complement well with the literature data, with the first-stage IDTs at high pressures and volume histories at all test conditions being first reported for better development and validation of chemical kinetic models. Additionally, a detailed chemical kinetic model for the cyclohexane oxidation has been developed and validated using both newly acquired experimental IDTs in this study and literature experimental studies (IDTs in RCMs and STs, species profiles in jet-stirred reactors, and laminar burning velocities). Unlike literature models, the proposed model was observed to provide an overall better prediction for experimental results over a wide range of conditions. Chemical kinetic analysis of the developed model was further conducted to identify the reaction pathways controlling the autoignition of cyclohexane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Isomeric effects on the reactivity of branched alkenes: An experimental and kinetic modeling study of methylbutenes

Here, a detailed experimental study of the low-to-intermediate temperature combustion of methylbutene isomers, i.e., branched C 5 alkenes, has been undertaken with multiple experimental facilities. Ignition delay times were measured at equivalence ratios 0.5–2.0, 685–1020 K and up to 45 bar condition from two rapid compression machines and showed slight deviation from an Arrhenius behavior for all three isomers, while their reactivity order differs as temperature changes. Sampled intermediates formed during the oxidation process of mixtures at 900–1150 K and 0.82 bar from a flow reactor and at 730 K and 20 bar from a rapid compression machine were analyzed using gas chromatography techniques. Trends in the formation and consumption of sampled intermediates were modeled using a kinetic model developed in this work for all three isomers. Rate of production and sensitivity analyses emphasize the role of double bond-specific reactions governing the global reactivity of these fuels. Additional studies of the addition reactions of HO 2 radicals to the double bond and to allylic radicals may improve the model performance.

2-Methyl-1-butene↗
DOE OSTI2022

A comprehensive experimental and kinetic modeling study of di-isobutylene isomers: Part 2

A wide variety of high temperature experimental data obtained in this study complement the data on the oxidation of the two di-isobutylene isomers presented in Part I and offers a basis for an extensive validation of the kinetic model developed in this study. Due to the increasing importance of unimolecular decomposition reactions in high-temperature combustion, we have investigated the di-isobutylene isomers in high dilution utilizing a pyrolysis microflow reactor and detected radical intermediates and stable products using vacuum ultraviolet (VUV) synchrotron radiation and photoelectron photoion coincidence (PEPICO) spectroscopy. Additional speciation data at oxidative conditions were also recorded utilizing a plug flow reactor at atmospheric pressure in the temperature range 725-1150 K at equivalence ratios of 1.0 and 3.0 and at residence times of 0.35 s and 0.22 s, respectively. Combustion products were analyzed using gas chromatography (GC) and mass spectrometry (MS). Ignition delay time measurements for di-isobutylene were performed at pressures of 15 and 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 diluted in 'air' in the temperature range 900-1400 K using a high-pressure shock-tube facility. New measurements of the laminar burning velocities of di-isobutylene/air flames are also presented. The experiments were performed using the heat flux method at atmospheric pressure and initial temperatures of 298-358 K. Moreover, data consistency was assessed with the help of analysis of the temperature and pressure dependencies of laminar burning velocity measurements, which was interpreted using an empirical power-law expression. Electronic structure calculations were performed to compute the energy barriers to the formation of many of the product species formed. The predictions of the present mechanism were found to be in adequate agreement with the wide variety of experimental measurements performed.

09 BIOMASS FUELS↗
DOE OSTI2022

Understanding the low-temperature chemistry of 1,2,4-trimethylbenzene

1,2,4-trimethylbenzene is an important representative aromatic component of gasoline/diesel/jet fuels and thus it is necessary to understand its low-temperature chemistry. In this paper, ignition delay times (IDTs) of both 1,2,4-trimethylbenzene (124TMB) and its blends with n -heptane were measured at engine-like conditions using both a high-pressure shock tube and a rapid compression machine for fuel in ‘air’ mixtures at pressures of 10 and 30 atm and at temperatures in the range 600 – 1100K. The experiments in this study show for the first time that 124TMB presents a two-stage ignition behavior at engine relevant conditions. Blending n -heptane with 124TMB can significantly increase mixture reactivity at temperatures below 1000K. A new detailed mechanism has been developed to simulate the experimentally measured IDT data. The mechanism can capture well the two-stage ignition behavior as well as the ignition delays at different pressures, equivalence ratios over a wide temperature range, for both pure fuels and their blended mixtures. Flux analyses show that the benzylic radicals (formed via H-atom abstraction from the methyl groups ortho-sites on 124TMB) can add to O 2 forming $\mathrm{R\dot{O}_2}$ radicals, which can isomerize to $\dot{Q}$OOH by intramolecular H-atom transfer from the ortho- methyl group and these $\dot{Q}$OOH radicals undergo a second addition to O 2 . This is analogous to the chain branching reaction pathways of alkanes. The chain branching reaction pathways are responsible for the first-stage heat release of 124TMB. In conclusion, the competitions between chain branching and both chain propagating and chain termination reaction pathways lead to a less pronounced negative temperature coefficient (NTC) behavior for 124TMB oxidation, compared to two-stage ignition behavior observed for alkanes and other fuels.

1,2,4-trimethylbenzene↗
DOE OSTI2022

An experimental and modeling study on autoignition of 2-phenylethanol and its blends with n-heptane

2-Phenylethanol (2-PE) is an aromatic alcohol with high research octane number, high octane sensitivity, and a potential to be produced using biomass. Considering that 2-PE can be used as a fuel additive for boosting the anti-knocking quality of gasoline in spark-ignition engines and as the low reactivity fuel or fuel component in dual-fuel reactivity controlled compression ignition (RCCI) engines, it is of fundamental and practical interest to understand the autoignition chemistry of 2-PE, especially at low-to-intermediate temperatures (<1000 K). Based upon the experimental ignition delay time (IDT) results of neat 2-PE obtained from our previous rapid compression machine (RCM) investigation and the literature shock tube study, a detailed chemical kinetic model of 2-PE is developed herein, covering low-to-high temperature regimes. Besides, RCM experiments using binary fuel blends of 2-PE and n-heptane (nC7) are conducted in this work to investigate the nC7/2-PE blending effects, as they represent a dual-fuel system for RCCI operations. Furthermore, the newly developed 2-PE model is merged with a well-validated nC7 kinetic model to generate the current nC7/2-PE binary blend model. Overall, the consolidated model reasonably predicts the experimental IDT data of neat 2-PE and nC7/2-PE blends, as well as captures the experimental effects of pressure, equivalence ratio, and blending ratio on autoignition. Finally, model-based chemical kinetic analyses are carried out to understand and identify the controlling chemistry accounting for the observed blending effects in RCM experiments. In conclusion, the analyses reveal that nC7 enhances 2-PE autoignition via providing extra $\dot{O}$H radicals to the shared radical pool, while the diminished nC7 promoting effect on 2-PE autoignition with increasing temperature is due to the negative temperature coefficient characteristics of nC7.

2-phenlyethanol↗
DOE OSTI2022

The role of cool-flame fluctuations in high-pressure spray flames, studied using high-speed optical diagnostics and Large-Eddy Simulations

Here this work investigates the low- and high-temperature ignition and combustion processes, applied to the Engine Combustion Network Spray A flame, combining advanced optical diagnostics and large-eddy simulations (LES). Simultaneous high-speed (50 kHz) formaldehyde (CH 2 0) planar laser-induced fluorescence (PLIF) and line-of-sight OH* chemiluminescence imaging were used to measure the low- and high-temperature flame, during ignition as well as during quasi-steady combustion. While tracking the cool flame at the laser sheet plane, the present experimental setup allows detection of distinct ignition spots and dynamic fluctuations of the lift-off length over time, which overcomes limitations for flame tracking when using schlieren imaging. After significant development to improve LES prediction of the low-and high-temperature flame position, both during the ignition processes and quasi-steady combustion, the simulations were analyzed to gain understanding of the mixture variance and how this variance affects formation/consumption of CH 2 0. Analysis of the high-temperature ignition period shows that a key improvement in the LES is the ability to predict heterogeneous ignition sites, not only in the head of the jet, but in shear layers at the jet edge close to the position where flame lift-off eventually stabilizes. The LES analysis also shows concentrated pockets of CH 2 0, in the center of jet and at 20 mm downstream of the injector (in regions where the equivalence ratio is greater than 6), that are of similar length scale and frequency as the experiment (approximately 5–6 kHz). The periodic oscillation of CH 2 0 match the frequency of pressure waves generated during auto-ignition and reflected within the constant-volume vessel throughout injection. The ability of LES to capture the periodic appearance and destruction of CH 2 0 is particularly important because these structures travel downstream and become rich premixed flames that affect soot production.

42 ENGINEERING↗
DOE OSTI2022

Molecular weight growth by the phenyl + cyclopentadienyl reaction: Well-skipping, ring-opening, and dissociation

Radical-radical reactions contribute to molecular weight growth of polycyclic aromatic hydrocarbons (PAHs), but their role is not well understood. The phenyl (Ph, C 6 H 5 ) + cyclopentadienyl (C 5 H 5 ) reaction has not been studied but can serve as a surrogate reaction for many reactions of larger aryl-σ radicals with resonance-stabilized π-radicals. The adducts of these reactions easily lose an H atom to produce a new π-radical. Here, through a combination of dilute flash pyrolysis experiments, theory, and simulation, we find that for the title reaction, substantial Ph—C 5 H 4 + H is formed, dominantly by a well-skipping pathway, at conditions around 30 Torr and 1400 K. This radical is thermally stable at moderate temperatures but decomposes at higher temperatures following ring opening of the 5-member ring. Products corresponding to the loss of H, C 2 H 2 , and C 3 H 3 are observed experimentally. Calculation of the C 11 H 9 potential energy surface affirms that these are expected decomposition products and reveals multiple possible pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The role of radical-radical chain-propagating pathways in the phenyl + propargyl reaction

Well-skipping radical-radical reactions can provide a chain-propagating pathway for formation of polycyclic radicals implicated in soot inception. Here we use controlled pyrolysis in a microreactor to isolate and examine the role of well-skipping channels in the phenyl (C 6 H 5 ) + propargyl (C 3 H 3 ) radical-radical reaction at temperatures of 800-1600 K and pressures near 25 Torr. The temperature and concentration dependence of the closed-shell (C 9 H 8 ) and radical (C 9 H 7 ) products are observed using electron-ionization mass spectrometry. The flow in the reactor is simulated using a boundary layer model employing a chemical mechanism based on recent rate coefficient calculations. Further, comparison between simulation and experiment shows reasonable agreement, within a factor of 3, while suggesting possible improvements to the model. In contrast, eliminating the well-skipping reactions from the chemistry mechanism causes a much larger discrepancy between simulation and experiment in the temperature dependence of the radical concentration, revealing that the well-skipping pathways, especially to form indenyl radical, are significant at temperatures of 1200 K and higher. While most C 9 H 7 forms by well-skipping at 25 Torr, an additional simulation indicates that the wellskipping channels only contribute around 3% of the C 9 H x yield at atmospheric pressure, thus indicating a negligible role of the well-skipping pathways at atmospheric and higher pressures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A comprehensive experimental and kinetic modeling study of di-isobutylene isomers: Part 1

We report di-isobutylene has received significant attention as a promising fuel blendstock, as it can be synthesized via biological routes and is a short-listed molecule from the Co-Optima initiative. Di-isobutylene is also popularly used as an alkene representative in multi-component surrogate models for engine studies of gasoline fuels. However, there is limited experimental data available in the literature for neat di-isobutylene under engine-like conditions. Hence, most existing di-isobutylene models have not been extensively validated, particularly at lower temperatures (< 1000 K). Most gasoline surrogate models include the di-isobutylene sub-mechanism published by Metcalfe et al. with little or no modification. The current study is undertaken to develop a detailed kinetic model for di-isobutylene and validate the model using a wide range of relevant experimental data. Part 1 of this study exclusively focuses on the low- to intermediate temperature kinetics of di-isobutylene. An upcoming part 2 discusses the high-temperature model development and validation of the relevant experimental targets. Ignition delay time measurements for the di-isobutylene isomers were performed at pressures ranging from 15 - 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 diluted in air and in the temperature range 650 - 900 K using two independent rapid compression machine facilities. In addition, measurements of species identified during the oxidation of these isomers were performed in a jet-stirred reactor and in a rapid compression machine. A detailed kinetic model for the di-isobutylene isomers is developed to capture the wide range of new experimental targets. For the first time, a comprehensive low-temperature chemistry submodel is included. The differences in the important reaction pathways for the accurate prediction of the oxidation of the two DIB isomers are compared using reaction path analysis. In conclusion, the most sensitive reactions controlling the ignition delay times of the DIB isomers under the pressure and temperature conditions necessary for autoignition in engines are identified.

09 BIOMASS FUELS↗
DOE OSTI2022

Investigating the kinetic effect of prenol on iso -octane auto-ignition by means of an experimental and modeling study

A detailed experimental and kinetic modeling study was dedicated to understand the reported octane hyperboosting effect of prenol, by means of the measurement of the ignition delay times of its blends with iso -octane, and measurement of the mole fraction profiles of the fuels and intermediates inside the ULille rapid compression machine. Here, these results show that prenol addition leads to a reduction of the first-stage ignition phenomena and negative temperature coefficient behavior, which is only qualitatively captured by the model and is consistent with knock resistance improvement. It is suggested that this behavior is caused by two different factors. The first originates from gas-phase reactivity of prenol, and spans from the formation of unreactive unsaturated species through resonance-stabilized radicals, thereby constituting a competitive pathway for the radical pool generated by iso -octane. The second is of catalytic nature and cannot be captured by means of gas-phase kinetic modeling, but could also play an important role in the behavior of prenol in internal combustion engines.

42 ENGINEERING↗
DOE OSTI2022

Numerical Study of PAHs and Soot Emissions from Gasoline–Methanol, Gasoline–Ethanol, and Gasoline– n -Butanol Blend Surrogates

Soot formation is an intricate phenomenon, and soot propensity of a fuel is interwoven with the fuel composition, physical and chemical properties, and combustion environment. Here, the present study examines the hypothesis that in addition to the chemical composition of the fuel, the sooting nature of the fuel is closely coupled with its chemical property known as octane sensitivity (S). With this motivation, the present study numerically investigates the effects of gasoline surrogate composition and its property, octane sensitivity (S), on polycyclic aromatic hydrocarbons (PAHs) and soot emissions. Four-component toluene primary reference fuel (TPRF)–alcohol blends, comprising iso-octane, n-heptane, toluene, and one of the three different alcohols- methanol, ethanol, and n-butanol, are used as gasoline surrogates. A total of 320 TPRF–alcohol mixtures, with S in the range of 1–10, are examined under laminar counterflow diffusion flame conditions. A detailed chemical mechanism coupled with a comprehensive soot model, which includes reactions for soot inception, surface growth, PAH condensation, and oxidation, is adopted. The analysis indicates that the toluene content in the fuel mixture has a prominent effect, while the alcohol content and octane sensitivity of the fuel have a weak correlation with the PAHs and soot. Thus, it is not clear if any of these three variables, namely, toluene content in the fuel, alcohol content in the fuel, and S, are individually sufficient to characterize the PAHs and soot across various blends. For this reason, a new variable (X CHO ) based on the elemental composition of the fuel mixture is identified and it is shown that X CHO along with S of the fuel characterize soot emissions satisfactorily. Further, a reaction path analysis indicates that the efficacy of alcohols in reducing soot emissions follows the order: methanol > ethanol > n-butanol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

An experimental and kinetic modeling study of the pyrolysis of isoprene, a significant biogenic hydrocarbon in naturally occurring vegetation fires

Isoprene dominates the carbon flux emitted by vegetation and constitutes 40% of non-methane biogenic emissions worldwide. Despite pyrolysis experiments at temperatures above 1000 K showing a link between isoprene combustion and aromatic species formation, comprehensive mechanistic research on isoprene is scarce in the literature. Here, in this work, we carry out an experimental and theoretical study to build, for the first time, a chemical kinetic model describing isoprene pyrolysis. The formation of polycyclic aromatic hydrocarbon (PAH) precursor species, often observed in vegetation fire plumes, is partially explained by isoprene pyrolysis experiments and theoretical modeling. Molecular dynamics (MD) simulations unveil reaction pathways from allylic isoprenyl radicals to allene and cyclopentadiene (CPD) intermediates, two relevant species detected in the experiments. Rate constants for these identified pathways are calculated using variational transition state theory to update the kinetic model, which is validated against single-pulse shock tube (SPST), and jet-stirred reactor (JSR) experimental data in the temperature range of 850–1690 K. The kinetic model presents satisfactory agreement with the SPST experimental data, and a reaction pathway analysis shows that association of propargyl radicals results in benzene formation. The JSR pathway analysis also identifies the prominent reactions for CPD, benzene, styrene, and toluene formation. Our model does not reproduce the CPD experimental profiles, indicating that additional studies are necessary. Overall, our findings advance the understanding of isoprene pyrolysis and its related atmospheric pollutants in naturally occurring vegetation fires where smoldering and oxygen-deficient combustion processes are present.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗