Engineering Papers⌕ Search

Engineering topics

Kugel, H. W.

Publications and source records attributed to Kugel, H. W..

At least 19 records

Supersonic Gas Injector for Plasma Fueling in the National Spherical Torus Experiment

A supersonic gas injector (SGI) has been developed for fueling and diagnostic applications on the National Spherical Torus Experiment (NSTX). It is comprised of a graphite converging-diverging Laval nozzle and a commercial piezoelectric gas valve mounted on a movable probe at a low-field-side midplane port location. Also mounted on the probe is a diagnostic package: a Langmuir probe, two thermocouples, and five pick-up coils for measuring toroidal, radial, vertical magnetic field components and magnetic fluctuations at the location of the SGI tip. The SGI flow rate is up to 33.25 Pa m 3 / (1.75 × 10 22 euterium particles/s), comparable to conventional NSTX gas injectors. The nozzle operates in a pulsed regime at room temperature and a reservoir gas pressure up to 665 kPa (5000 Torr). The deuterium jet Mach number of about 4 and the divergence half-angle of 5 to 25 deg have been measured in laboratory experiments simulating the NSTX environment. Reliable operation of the SGI and all mounted diagnostics at distances 0.01 to 0.20 m from the plasma separatrix has been demonstrated in NSTX experiments. The SGI has been used for fueling of ohmic and 2- to 4-MW neutral beam injection–heated L- and H-mode plasmas. Fueling efficiency in the range 0.1 to 0.3 has been obtained from the plasma electron inventory analysis. In conclusion, the SGI-fueling–based plasma discharge scenarios enabling better density control have been developed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Dependence of recycling and edge profiles on lithium evaporation in high triangularity, high performance NSTX H-mode discharges

In this paper, the effects of a pre-discharge lithium evaporation variation on highly shaped discharges in the National Spherical Torus Experiment (NSTX) are documented. Lithium wall conditioning ('dose') was routinely applied onto graphite plasma facing components between discharges in NSTX, partly to reduce recycling. Reduced D-alpha, emission from the lower and upper divertor and center stack was observed, as well as reduced midplane neutral pressure; the magnitude of reduction increased with the pre-discharge lithium dose. Improved energy confinement, both raw tau(E) and H-factor normalized to scalings, with increasing lithium dose was also observed. At the highest doses, we also observed elimination of edge-localized modes. The midplane edge plasma profiles were dramatically altered, comparable to lithium dose scans at lower shaping, where the strike point was farther from the lithium deposition centroid. This indicates that the benefits of lithium conditioning should apply to the highly shaped plasmas planned in NSTX-U. (C) 2014 Elsevier B.V. All rights reserved.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma Facing Surface Composition During NSTX Li Experiments

Lithium conditioned plasma facing surfaces have lowered recycling and enhanced plasma performance on many fusion devices. However, the nature of the plasma-lithium surface interaction has been obscured by the difficulty of in-tokamak surface analysis. We report laboratory studies of the chemical composition of lithium surfaces exposed to typical residual gases found in tokamaks. Solid lithium and a molybdenum alloy (TZM) coated with lithium has been examined using x-ray photoelectron spectroscopy, temperature programmed desorption, and Auger electron spectroscopy both in ultrahigh vacuum conditions and after exposure to trace gases. Lithium surfaces near room temperature were oxidized after exposure to 1-2 Langmuirs of oxygen or water vapor. The oxidation rate by carbon monoxide was four times less. Lithiated PFC surfaces in tokamaks will be oxidized in about 100 s depending on the tokamak vacuum conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation And Modeling Of Inner Divertor Re-attachment In Discharges With Lithium Coatings in NSTX

In the National Spherical Torus Experiment (NSTX), modifications to the inner divertor plasma regimes are observed in high triangularity, H-mode, NBI heated discharges due to lithium coatings evaporated on the plasma facing components. In particular, the drop in the recombination rate, the reduced neutral pressure and the reduced electron density (inferred from Stark broadening measurements of high-n deuterium Balmer lines) suggested that the inner divertor, which is usually detached in discharges without lithium, re-attached. Experimental results are compared to simulations obtained with a 1D partially ionized plasma transport model integrated in the non-local thermodynamic equilibrium radiation transport code CRETIN to understand how the reduced recycling affects the divertor parameters in NSTX discharges with lithium coatings.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observation and modeling of inner divertor re-attachment in discharges with lithium coatings in NSTX

In the National Spherical Torus Experiment (NSTX), modifications to the inner divertor plasma regimes are observed in high triangularity, H-mode, NBI heated discharges due to lithium coatings evaporated on the plasma facing components. In particular, the drop in the recombination rate, the reduced neutral pressure and the reduced electron density (inferred from Stark broadening measurements of high-n deuterium Balmer lines) suggested that the inner divertor, which is usually detached in discharges without lithium, re-attached. In conclusion, experimental results are compared to simulations obtained with a 1D partially ionized plasma transport model integrated in the non-local thermodynamic equilibrium radiation transport code CRETIN to understand how the reduced recycling affects the divertor parameters in NSTX discharges with lithium coatings.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulation of Diffusive Lithium Evaporation Onto the NSTX Vessel Walls

A model for simulating the diffusive evaporation of lithium into a helium filled NSTX vacuum vessel is described and validated against an initial set of deposition experiments. The DEGAS 2 based model consists of a three-dimensional representation of the vacuum vessel, the elastic scattering process, and a kinetic description of the evaporated atoms. Additional assumptions are required to account for deuterium out-gassing during the validation experiments. The model agrees with the data over a range of pressures to within the estimated uncertainties. Suggestions are made for more discriminating experiments that will lead to an improved model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reduction of low-Z impurities during plasma start-up

Reduction of low-Z impurities is essential during the plasma start-up in tokamaks. For plasma start-up using the method of Coaxial Helicity Injection (CHI) it has been found here that conventional wall conditioning methods have been inadequate to generate a plasma with acceptably low levels of low-Z impurities. NSTX has now used a new combination of techniques to improve CHI start-up performance. These are the use of high-current discharge cleaning of the lower divertor surfaces, which function as the CHI electrodes, to remove loosely bound impurities, controlling the poloidal magnetic field to avoid plasma wall contact and the use of evaporated lithium coatings of the electrodes and other plasma-facing surfaces. Together, these techniques have enabled significant improvement in NSTX CHI performance leading to a saving of central solenoid flux and the first observation of electron temperatures during CHI exceeding the oxygen radiation barrier temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements and 2-D modeling of recycling and edge transport in discharges with lithium-coated PFCs in NSTX

We report the application of lithium coatings on plasma facing components has been shown to profoundly affect plasma performance in the National Spherical Torus Experiment, improving energy confinement and eliminating edge-localized modes. The edge particle balance during these ELM-free discharges has been studied through 2-D plasma-neutrals modeling, constrained by measurements of the upstream plasma density and temperature profiles and the divertor heat flux and $\mathcal{D}_α$ emission. The calculations indicate that the reduction in divertor $\mathcal{D}_α$ emission with lithium coatings applied is consistent with a drop in recycling coefficient from $\mathcal{R}$ ~ 0.98 to $\mathcal{R}$ ~ 0.9. The change in recycling is not sufficient to account for the change in edge density profiles: interpretive modeling indicates similar transport coefficients within the edge transport barrier ($D/χ_e$ ~ 0.2/1.0 m 2 /s), but a widening of the barrier with lithium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗