Engineering Papers⌕ Search

Engineering topics

Kuech, Thomas F.

Publications and source records attributed to Kuech, Thomas F..

At least 19 records

Instrument for in situ hard x-ray nanobeam characterization during epitaxial crystallization and materials transformations

Solid-phase epitaxy (SPE) and other three-dimensional epitaxial crystallization processes pose challenging structural and chemical characterization problems. The concentration of defects, the spatial distribution of elastic strain, and the chemical state of ions each vary with nanoscale characteristic length scales and depend sensitively on the gas environment and elastic boundary conditions during growth. The lateral or three-dimensional propagation of crystalline interfaces in SPE has nanoscale or submicrometer characteristic distances during typical crystallization times. Here, an in situ synchrotron hard x-ray instrument allows these features to be studied during deposition and crystallization using diffraction, resonant scattering, nanobeam and coherent diffraction imaging, and reflectivity. The instrument incorporates a compact deposition system allowing the use of short-working-distance x-ray focusing optics. Layers are deposited using radio-frequency magnetron sputtering and evaporation sources. The deposition system provides control of the gas atmosphere and sample temperature. The sample is positioned using a stable mechanical design to minimize vibration and drift and employs precise translation stages to enable nanobeam experiments. Results of in situ x-ray characterization of the amorphous thin film deposition process for a SrTiO 3 /BaTiO 3 multilayer illustrate implementation of this instrument.

47 OTHER INSTRUMENTATION↗

Rates of levoglucosanol hydrogenolysis over Brønsted and Lewis acid sites on platinum silica-alumina catalysts synthesized by atomic layer deposition

Nanoscale coatings of AlO x were deposited onto SiO 2 using atomic layer deposition (ALD) to synthesize amorphous silica-alumina (SiAl) catalysts, and these catalysts were investigated for levoglucosanol (Lgol) hydrogenolysis. With decreasing Al 2 O 3 loading, the ratio of Brønsted to Lewis acid sites, measured by NH 3 -TPD and pyridine-FTIR, systematically increases, while the Al coordination, measured by solid state 27 Al NMR, decreases. These structural changes correspond to an increasing mass-normalized rate of Lgol hydrogenolysis. We model the mass-normalized reaction rate as the sum of independent contributions from Brønsted and Lewis sites, showing that Brønsted acid sites on ALD-AlO x /SiO 2 catalysts have a 6-times higher turnover frequency (TOF) than Lewis acid sites on these catalysts. Additionally, Lewis acid sites on ALD-AlO x /SiO 2 catalysts (potentially related to Al(V) species) have a 4-times higher TOF than Lewis acid sites on bulk γ-Al 2 O 3 . The overall mass-normalized reactivity of ALD-AlO x /SiO 2 catalysts is due to Lewis acid sites at the highest Al 2 O 3 loading, while it is predominantly due to Brønsted acid sites at the lowest Al 2 O 3 loadings. In conclusion, this work provides a new approach to synthesize amorphous SiAls with tunable Brønsted/Lewis acid site ratio and reveals differences in the reactivity of Brønsted and Lewis acid sites on these materials.

36 MATERIALS SCIENCE↗

Seeded Lateral Solid-Phase Crystallization of the Perovskite Oxide SrTiO 3

Crystallization from an amorphous precursor presents a new route to control the properties of complex oxides by selecting their nanoscale morphology. A key challenge in crystal growth from the amorphous form is to select the locations of nucleation and the crystallographic orientation of the resulting crystals. Nucleation sites for crystallization of the prototypical perovskite complex oxide SrTiO 3 (STO) from its amorphous form can be reproducibly introduced using nanoscale seed crystals. The results of two seeding strategies are reported here: (i) SrRuO 3 (SRO) (001)-oriented nanomembranes and (ii) STO nanocrystalline seeds. Amorphous STO crystallizes laterally over distances of several microns from the seeds before encountering separately nucleated crystals. The lateral crystallization rates for both types of seeding methods are close to the values measured in solidphase epitaxy (SPE) of STO on single-crystal substrates. The lateral crystallization distances along different crystallographic orientations are equal, indicating that the lateral crystallization rate is isotropic. The isotropic crystallization suggests that the rate-limiting steps for crystallization occur within the amorphous STO away from the amorphous/crystalline interface. In addition to the lateral crystallization, STO crystallizes on top of the planar SRO nanomembrane seeds via SPE, forming partially relaxed [001]-oriented heteroepitaxial STO layers. The in-plane orientation of laterally crystallized STO near the SRO nanomembrane seeds exhibits overall polycrystallinity with regions in which micron-scale grains of laterally crystallized STO share the same in-plane orientation as the SRO nanomembrane seeds. Crystallization from seed crystals provides opportunities to create a wide range of other perovskite oxides in nanoscale geometries.

36 MATERIALS SCIENCE↗

High throughput semiconductor deposition system

A reactor for growing or depositing semiconductor films or devices. The reactor may be designed for inline production of III-V materials grown by hydride vapor phase epitaxy (HVPE). The operating principles of the HVPE reactor can be used to provide a completely or partially inline reactor for many different materials. An exemplary design of the reactor is shown in the attached drawings. In some instances, all or many of the pieces of the reactor formed of quartz, such as welded quartz tubing, while other reactors are made from metal with appropriate corrosion resistant coatings such as quartz or other materials, e.g., corrosion resistant material, or stainless steel tubing or pipes may be used with a corrosion resistant material useful with HVPE-type reactants and gases. Using HVPE in the reactor allows use of lower-cost precursors at higher deposition rates such as in the range of 1 to 5 .mu.m/minute.

Young, David L.↗

Synthesis Gas Conversion over Rh/Mo Catalysts Prepared by Atomic Layer Deposition

Conversion of synthesis gas into value-added products, including oxygenates and C 2+ hydrocarbons, was studied at 523 K, 580 psi, and a 1/1 CO/H 2 ratio over Rh catalysts on catalyst supports prepared by atomic layer deposition (ALD) of molybdenum and tungsten species on silica. The reactivity measurements showed that coating the silica support with molybdenum and tungsten species helped to suppress the methane selectivity and promote the overall conversion rate. When the silica support was coated with five cycles of β-Mo 2 C, the methane selectivity decreased from 32% (1% Rh/SiO 2 ) to 13% (1% Rh/5c-Mo 2 C/SiO 2 ), and the overall product rate increased 33 times from 0.4 to 12.7 mmol min –1 (g of Rh) –1 . CO-FTIR results showed that supporting Rh on silica led to the formation of Rh(211) facets, which favored the formation of methane and had a higher CO conversion rate. Rh on a MoO 3 /SiO 2 support prepared by ALD was found to be the most active catalyst while maintaining the suppression of methane selectivity, showing an overall rate ~60 times higher than that of 1% Rh/SiO 2 . A reaction pathway is proposed, in which hydrogenation steps are promoted most significantly by Mo and W species, followed by promotion of CO insertion steps for ethanol synthesis and C–C coupling steps for hydrocarbon formation. CO-FTIR results showed that 1% Rh/MoO 3 /SiO 2 has the highest proportion of gem-dicarbonyl adsorption sites and the lowest proportion of bridge-bonded CO adsorption sites. As a result, the rate of methanol formation shows a positive correlation with the number of sites that form gem-dicarbonyl species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis Gas Conversion over Rh-Mn-W x C/SiO 2 Catalysts Prepared by Atomic Layer Deposition

The catalytic conversion of synthesis gas to value-added oxygenates and light hydrocarbons was studied here on Rh and Rh–Mn clusters on tungsten carbide-overcoated silica (W x C/SiO 2 ) at 523 K, 580 psi, and CO/H 2 = 1/1. The W x C-modified SiO 2 support was prepared by the overcoating of WO x on SiO 2 using atomic layer deposition (ALD) followed by carburization. The reactivities of Rh/W x C/SiO 2 catalysts with varying number of ALD cycles (number of cycles = 2, 5, 10, 20, and 30) were measured and showed that 5 ALD cycles of WxC suppressed the formation of methane. All W x C-modified catalysts showed enhancement in selectivity toward methanol and ethanol through CO hydrogenation and acetaldehyde hydrogenation, respectively. These catalysts also improved the overall turnover frequency (TOF). The addition of Mn species further promoted the activity and the selectivity toward ethanol and C 2+ hydrocarbons, especially light alkenes. The best performing Rh-2Mn/5cycle-W x C/SiO 2 catalyst (Rh:Mn molar ratio = 1:2) achieved 84.7% selectivity toward valuable oxygenates and C 2+ hydrocarbons with a ratio of alkenes to alkanes equal to 1.7, compared to Rh/SiO 2 which exhibited 80.4% selectivity toward the products aforementioned with a ratio of 0.5. The overall TOF was 20 times higher than that over Rh/SiO 2 (i.e., 5.6 × 10 –2 s –1 vs 2.9 × 10 –3 s –1 ). X-ray diffraction revealed that the existence of W 2 C, which was the dominant phase in Rh/5cycle-W x C/SiO 2 , favored the suppression of methane and enhanced the production of alcohols and C 2+ hydrocarbons compared to the WC support. Density functional theory calculations for Rh 19 , Rh 31 , and Rh 37 clusters on various WC surfaces suggested that the shape of Rh clusters is condition dependent and subject to H 2 pressure. The C- and O- binding energies on various sites for the clusters were used with scaling relations to probe their catalytic activity. With the use of this approach, the increase in the O binding energy when moving from the SiO 2 -supported Rh 37 cluster to the WC-supported cluster leads to an increase in the activity of Rh/W x C/SiO 2 at the expense of the reduction in the number of sites that are selective toward C 2 oxygenates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Transition state redox during dynamical processes in semiconductors and insulators

Activation barriers associated with ion diffusion and chemical reactions are vital to understand and predict a wide range of phenomena, such as material growth, ion transport, and catalysis. In the calculation of activation barriers for non-redox processes in semiconductors and insulators, it has been widely assumed that the charge state remains fixed to that of the initial electronic ground state throughout a dynamical process. In this work, we demonstrate that this assumption is generally inaccurate and that a rate-limiting transition state can have a different charge state from the initial ground state. This phenomenon can significantly lower the activation barrier of a dynamical process that depends strongly on charge state, such as carbon vacancy diffusion in 4H-SiC. With inclusion of such transition state redox, the activation barrier varies continuously with Fermi level, in contrast to the step-line feature predicted by the traditional fixed-charge assumption. In this study, a straightforward approach to include the transition state redox effect is provided, the typical situations where the effect plays a significant role are identified, and the relevant electron dynamics are discussed.

36 MATERIALS SCIENCE↗

High throughput semiconductor deposition system

A reactor for growing or depositing semiconductor films or devices. The reactor may be designed for inline production of III-V materials grown by hydride vapor phase epitaxy (HVPE). The operating principles of the HVPE reactor can be used to provide a completely or partially inline reactor for many different materials. An exemplary design of the reactor is shown in the attached drawings. In some instances, all or many of the pieces of the reactor formed of quartz, such as welded quartz tubing, while other reactors are made from metal with appropriate corrosion resistant coatings such as quartz or other materials, e.g., corrosion resistant material, or stainless steel tubing or pipes may be used with a corrosion resistant material useful with HVPE-type reactants and gases. Using HVPE in the reactor allows use of lower-cost precursors at higher deposition rates such as in the range of 1 to 5 .mu.m/minute.

36 MATERIALS SCIENCE↗

Understanding and reducing deleterious defects in the metastable alloy GaAsBi

Technological applications of novel metastable materials are frequently inhibited by abundant defects residing in these materials. Using first-principles methods, we investigate the defect thermodynamics and phase segregation in the technologically important metastable alloy GaAsBi. Our calculations predict defect energy levels in good agreement with those from numerous previous experiments and clarify the defect structures giving rise to these levels. We find that vacancies in some charge states become metastable or unstable with respect to antisite formation, and this instability is a general characteristic of zincblende semiconductors with small ionicity. The dominant point defects that degrade the electronic and optical performances are predicted to be As Ga , Bi Ga , As Ga +Bi As , Bi Ga +Bi As , V Ga and V Ga +Bi As , of which the first four and last two defects are minority-electron and minority-hole traps, respectively. V Ga is also observed to have a critical role in controlling metastable Bi supersaturation by mediating Bi diffusion and clustering. To reduce the influences of these deleterious defects, we suggest shifting the growth away from an As-rich condition and/or using hydrogen passivation to reduce the minority-carrier traps. In conclusion, we expect this work to aid in the applications of GaAsBi for novel electronic and optoelectronic devices and to illuminate the control of deleterious defects in other metastable materials.

36 MATERIALS SCIENCE↗

Growth far from equilibrium: Examples from III-V semiconductors

The development of new applications has driven the field of materials design and synthesis to investigate materials that are not thermodynamically stable phases. Materials which are not thermodynamically stable can be synthesized and used in many applications. These materials are kinetically stabilized during use. The formation of such metastable materials requires both an understanding of the associated thermochemistry and the key surface transport processes present during growth. Phase separation is most easily accomplished at the growth surface during synthesis where mass transport is most rapid. These surface transport processes are sensitive to the surface stoichiometry, reconstruction, and chemistry as well as the growth temperature. The formation of new metastable semiconducting alloys with compositions deep within a compositional miscibility gap serves as model systems for the understanding of the surface chemical and physical processes controlling their formation. The GaAs{sub 1−y}Bi{sub y} system is used here to elucidate the role of surface chemistry in the formation of a homogeneous metastable composition during the chemical vapor deposition of the alloy system.

36 MATERIALS SCIENCE↗

Optimizing AlF{sub 3} atomic layer deposition using trimethylaluminum and TaF{sub 5}: Application to high voltage Li-ion battery cathodes

Atomic layer deposition (ALD) of conformal AlF{sub 3} coatings onto both flat silicon substrates and high-voltage LiNi{sub 0.5}Mn{sub 0.3}Co{sub 0.2}O{sub 2} (NMC) Li-ion battery cathode powders was investigated using a Al(CH{sub 3}){sub 3}/TaF{sub 5} precursor combination. This optimized approach employs easily handled ALD precursors, while also obviating the use of highly toxic HF(g). In studies conducted on planar Si wafers, the film's growth mode was dictated by a competition between the desorption and decomposition of Ta reaction byproducts. At T ≥ 200 °C, a rapid decomposition of the Ta reaction byproducts to TaC led to continuous deposition and high concentrations of TaC in the films. A self-limited ALD growth mode was found to occur when the deposition temperature was reduced to 125 °C, and the TaF{sub 5} exposures were followed by an extended purge. The lower temperature process suppressed conversion of TaF{sub x}(CH{sub 3}){sub 5−x} to nonvolatile TaC, and the long purges enabled nearly complete TaF{sub x}(CH{sub 3}){sub 5−x} desorption, leaving behind the AlF{sub 3} thin films. NMC cathode powders were coated using these optimized conditions, and coin cells employing these coated cathode particles exhibited significant improvements in charge capacity fade at high discharge rates.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗