Toward Phase and Catalysis Control: Tracking the Formation of Intermetallic Nanoparticles at Atomic Scale
Not Available
Engineering topics
Publications and source records attributed to Kramer, Matthew J..
Not Available
Abstract not provided
To reduce material and processing costs of commercial permanent magnets and to attempt to fill the empty niche of energy products, 10–20 MGOe, between low-flux (ferrites, alnico) and high-flux (Nd 2 Fe 14 B- and SmCo 5 -type) magnets, we report the synthesis, structure, magnetic properties, and modeling of Ta-, Cu-, and Fe-substituted CeCo 5 . Using a self-flux technique, we grow single crystals of Ce 15.1 Ta 1.0 Co 74.4 Cu 9.5 , Ce 16.3 Ta 0.6 Co 68.9 Cu 14.2 , Ce 15.7 Ta 0.6 Co 67.8 Cu 15.9 , Ce 16.3 Ta 0.3 Co 61.7 Cu 21.7 , and Ce 14.3 Ta 1.0 Co 62.0 Fe 12.3 Cu 10.4 . X-ray-diffraction analysis shows that these materials retain a CaCu 5 substructure and incorporate small amounts of Ta in the form of “dumbbells,” filling the 2e crystallographic sites within the one-dimensional hexagonal channel with the 1a Ce site, whereas Co, Cu, and Fe are statistically distributed among the 2c and 3g crystallographic sites. Scanning-electron-microscopy, energy-dispersive-x-ray-spectroscopy, and scanning-transmission-electron-microscopy examinations provide strong evidence of the single-phase nature of the as-grown crystals, even though they readily exhibit significant magnetic coercivities of approximately 1.6 kOe to approximately 1.8 kOe caused by Co-enriched, nanosized structural defects and faults that can serve as pinning sites. Heat treatments at 1040°C for 10 h and hardening at 400°C for 4 h lead to the formation of a so-called composite crystal with a bimodal microstructure that consists of a Ta-poor matrix and Ta-rich laminal precipitates. Formation of the composite crystal during the heat treatment creates a three-dimensional array of extended defects within a primarily single-grain single crystal, which greatly improves its magnetic characteristics. Possible causes for the formation of the composite crystal may be associated with Ta atoms leaving matrix interstices at lower temperatures and/or matrix degradation induced by decreased miscibility at lower temperatures. Furthermore Fe strongly increases both the Curie temperature and magnetization of the system resulting, in ( BH ) max ≈ 13 MGOe at room temperature.
The promise of magnetic skyrmions in future spintronic devices hinges on their topologically enhanced stability and the ability to be manipulated by external fields. The technological advantages of nonvolatile zero-field skyrmion lattice (SkL) are significant if their stability and reliability can be demonstrated over a broad temperature range. Here in this paper, we study the relaxation dynamics including the evolution and lifetime of zero-field skyrmions generated from field cooling (FC) in an FeGe single-crystal plate via in situ Lorentz transmission electron microscopy (L-TEM). Three types of dynamic switching between zero-field skyrmions and stripes are identified and distinguished. Moreover, the generation and annihilation of these metastable skyrmions can be tailored during and after FC by varying the magnetic fields and the temperature. Finally, this dynamic relaxation behavior under the external fields provides a new understanding of zero-field skyrmions for their stability and reliability in spintronic applications and also raises new questions for theoretical models of skyrmion systems.
Additive manufacturing techniques for fabricating bonded magnets have the potential to reduce manufacturing cost and time-to-market of products and address the criticality of rare-earth elements (REEs), which is a concern for economic design of dependent applications such as permanent magnet machines. We investigated the magnetic alignment of anisotropic bonded magnet material comprising 65 vol.% Nd-Fe-B in nylon-12 produced by extrusion in a 20-W brushless direct current surface permanent magnet motor for submersible water pump application using finite element analysis. The results predict that sufficient alignment for this application could be obtained at low alignment fields (μoH ≤ 1 T) with a reduction in the volume of critical materials by up to 40% compared with isotropic permanent magnets. Furthermore, this demonstrates the economic feasibility of incorporating a magnetic alignment field source into additive manufacturing systems for bonded magnets, and the potential of aligned anisotropic bonded magnets to address REE criticality.
Magnetic property enhancement of alnico, a rare-earth free permanent magnet, is highly dependent on both the initial microstructure and the evolution of the spinodal decomposition (SD) inside each grain during the heat treatment process. The size, shape and distribution of the magnetic FeCo-rich (α 1 ) phase embedded in continuous non-magnetic AlNi-rich (α 2 ) phase as well as a minor Cu-enriched phase residing in between are shown to be crucial in controlling coercivity. Phase and magnetic domain morphology in a commercial alnico 9 alloy was studied using a combination of structural characterization techniques, including scanning electron microscopy, electron backscatter diffraction, aberration-corrected scanning transmission electron microscopy and Lorentz microscopy. Our results showed that casting created structural nonuniformity and defects, such as porosity, TiS 2 precipitates and grain misorientation, are heterogeneously distributed, with the center section having the best crystallographic orientation and minimal defects. The optimal spinodal is a “mosaic structure”, composed of rod-shape α1 phase with {110} or {100} planar faceting and diameter of ~30–45nm. There is also a Cu-enriched phase residing at the corners of two < 110 > facets of the α1 phase. Furthermore, it was observed that grain boundary phase reverse magnetization direction at lower external magnetic field compared to the SD region inside the grain. Improving grain orientation uniformity, reducing detrimental grain boundary phase volume fraction, and the branching of the α 1 rods, as well as their diameter, are promising routes to improve energy product of alnico.
Here, the microstructural evolution of Fe-6.5 wt.% Si alloy during rapid solidification was studied over a quenching rate of 4 × 10 4 K/s to 8 ×10 5 K/s. The solidification and solid-state diffusional transformation processes during rapid cooling were analyzed via thermodynamic and kinetic calculations. The Allen-Cahn theory was adapted to model the experimentally measured bcc_B2 antiphase domain sizes under different cooling rates. The model was calibrated based on the experimentally determined bcc_B2 antiphase domain sizes for different wheel speeds and the resulting cooling rates. Good correspondence of the theoretical and experimental data was obtained over the entire experimental range of cooling rates. Along with the asymptotic domain size value at the infinite cooling rates, the developed model represents a reliable extrapolation for the cooling rate > 10 6 K/s and allows one to optimize the quenching process.
Here, single crystals of AlFe 2 B 2 have been grown using the self-flux growth method, and then we measured the structural properties, temperature- and field-dependent magnetization, and temperature-dependent electrical resistivity at ambient as well as high pressure. The Curie temperature of AlFe 2 B 2 is determined to be 274 K. The measured saturation magnetization and the effective moment for the paramagnetic Fe ion indicate the itinerant nature of the magnetism with a Rhode-Wohlfarth ratio M C /M sat ≈ 1.14. Temperature-dependent resistivity measurements under hydrostatic pressure show that transition temperature T C is suppressed down to 255 K for p = 2.24 GPa pressure with a suppression rate of ~–8.9 K/GPa. The anisotropy fields and magnetocrystalline anisotropy constants are in reasonable agreement with density functional theory calculations.
Explore the source record for details and available documents.
A metastable ε-Al 60 Sm 11 phase appears during the initial devitrification of as-quenched Al-10.2 at.% Sm glasses. The ε phase is nonstoichiometric in nature since Al occupation is observed on the 16 f Sm lattice sites. Scanning transmission electron microscopic images reveal profound spatial correlation of Sm content on these sites, which cannot be explained by the “average crystal” description from Rietveld analysis of diffraction data. Thermodynamically favorable configurations, established by Monte Carlo (MC) simulations based on a cluster-expansion model, also give qualitatively different correlation functions from experimental observations. On the other hand, molecular dynamics simulations of the growth of ε-Al 60 Sm 11 in undercooled liquid show that when the diffusion range of Sm is limited to ~4 Å, the correlation function of the as-grown crystal structure agrees well with that of the scanning transmission electronic microscopy (STEM) images. Furthermore, our results show that kinetic effects, especially the limited diffusivity of Sm atoms plays the fundamental role in determining the nonstoichiometric site occupancies of the ε-Al 60 Sm 11 phase during the crystallization process.
In situ X-ray-based measurements of the laser powder bed fusion (LPBF) additive manufacturing process produce unique data for model validation and improved process understanding. Synchrotron X-ray imaging and diffraction provide high resolution, bulk sensitive information with sufficient sampling rates to probe melt pool dynamics as well as phase and microstructure evolution. Here, we describe a laboratory-scale LPBF test bed designed to accommodate diffraction and imaging experiments at a synchrotron X-ray source during LPBF operation. We also present experimental results using Ti-6Al-4V, a widely used aerospace alloy, as a model system. Both imaging and diffraction experiments were carried out at the Stanford Synchrotron Radiation Lightsource. Melt pool dynamics were imaged at frame rates up to 4 kHz with a ~1.1 μm effective pixel size and revealed the formation of keyhole pores along the melt track due to vapor recoil forces. Diffraction experiments at sampling rates of 1 kHz captured phase evolution and lattice contraction during the rapid cooling present in LPBF within a ~50 × 100 μm area. In conclusion, we also discuss the utility of these measurements for model validation and process improvement.
Abstract not provided
An estimated 750,000 new hybrid electric and plug-in battery vehicles, most with permanent magnet synchronous alternating current (PMAC) drive motors, took to the road in 2016 alone. Accompanied by 40% year over year growth in the EV market significant challenges exist in producing large quantities of permanent magnets (on the order of tens of millions) for reliable, low-cost traction motors [IE Agency, Energy Technology Perspectives (2017)]. Since the rare earth permanent magnet (REPM) market is essentially 100% net import reliant in the United States and has proven to have an unstable cost and supply structure in recent years, a replacement RE-free PM material must be designed or selected, fully developed, and implemented. Alnico, with its high saturation magnetization and excellent thermal stability, appears to be uniquely suited for this task. Further, while alnico typically has been considered a relatively low coercivity hard magnet, strides have been made to increase the coercivity to levels suitable for traction drive motors [W Tang, IEEE Trans. Magn., 51 (2015)]. If a simple non-cast approach for achieving near [001] easy axis grain aligned permanent magnets can be found, this would allow massproduced final-shape anisotropic high energy product magnets suitable for usage in compact high RPM rotor designs. Therefore, a powder metallurgical approach is being explored that uses classic compression molding with “de-bind and sinter” methods, where a novel applied uniaxial loading, and an applied magnetic field may create final-shape magnets with highly textured resulting microstructures by two different mechanisms. Results indicate a positive correlation between applied uniaxial load and resulting texture (Fig. 1), along with benefits from using an applied magnetic field for improved texture, as well. Lastly, the apparent mechanisms and resulting properties will be described using closed loop hysteresisgraph measurements, EBSD orientation mapping, and high-resolution SEM.
Recent experiments on devitrification of Al 90 Sm 10 amorphous alloys revealed an unusual polymorphic transformation to a complex cubic crystal structure called the ε-Al 60 Sm 11 phase. Molecular dynamics simulations of the growth of the stoichiometric ε-phase seed in contact with an undercooled Al-10 at% Sm liquid are performed to elucidate the microscopic process of transformation. The as-grown crystal and undercooled liquid possess similar local order around Al atoms whereas a rigid network defined by the Sm sub-lattice develops during the growth. Using a template-cluster alignment method, we define an order parameter to characterize the structural evolution in the system. Estimates of the attachment rate is ${R}_{{\rm{a}}}=8.70\times {10}^{-4}$ Å-2 ns-1 and detachment rate is ${R}_{{\rm{d}}}=3.83\times {10}^{-4}$ Å-2 ns-1 at the interface between ε-Al 60 Sm 11 and Al-10 at% Sm liquid at 800 K.
An accurate and transferable cluster-expansion model for complex quinary alloys is developed. Lattice Monte Carlo simulation enabled by this cluster-expansion model is used to investigate temperature-dependent atomic structure of alnico alloys, which are considered as promising high-performance non-rare-earth permanent-magnet materials for high-temperature applications. The results of the Monte Carlo simulations are consistent with available experimental data and provide useful insights into phase decomposition, selection, and chemical ordering in alnico. The simulations also reveal a previously unrecognized D 0 3 alloy phase. This phase is very rich in Ni and exhibits very weak magnetization. In conclusion, manipulating the size and location of this phase provides a possible route to improve the magnetic properties of alnico, especially coercivity.
Investigating the unknown structure of the complex cubic phase, previously observed to crystallize from melt-spun amorphous Al–10 at.% Sm alloy, we determine the structure in full site-occupancy detail, highlighting several critical structural features that govern the far-from-equilibrium phase selection pathway. Using an efficient genetic algorithm combining molecular dynamics, density functional theory, and x-ray diffraction, the structure is clearly identified as body-centered cubic Im¯3m (No. 229) with ~140 atoms per cubic unit cell and a lattice parameter of 1.4 nm. The complex structure is further refined to elucidate the detailed site occupancy, revealing full Sm occupancy on 6b sites and split Sm/Al occupancy on 16f sites. Based on the refined site occupancy associated with the experimentally observed phase, we term this phase ε–Al 60 Sm 11 (bcc), corresponding to the limiting situation when all 16f sites are occupied by Sm. However, it should be recognized that the range of solubility enabled by split occupancy at Sm sites is an important feature in phase selection under experimental conditions, permitting an avenue for transition with little or no chemical partitioning. Our analysis shows that the ε–Al 60 Sm 11 (bcc) exhibits a “3-6-6-1” first-shell packing around Sm centers on 16f sites, the same dominant motif exhibited by the undercooled liquid. Here, the coincident motif supports the notion that liquid/glass ordering at high undercooling may give rise to topological invariants between the noncrystalline and crystalline states that provide kinetic pathways to metastable phases that are not accessible during near-equilibrium processing.
Micromagnetic simulations of alnico show substantial deviations from Stoner-Wohlfarth behavior due to the unique size and spatial distribution of the rod-like Fe-Co phase formed during spinodal decomposition in an external magnetic field. Furthemore, the maximum coercivity is limited by single-rod effects, especially deviations from ellipsoidal shape, and by interactions between the rods. In both the exchange interaction between connected rods and magnetostatic we consider the interaction between rods, and the results of our calculations show good agreement with recent experiments. Unlike systems dominated by magnetocrystalline anisotropy, coercivity in alnico is highly dependent on size, shape, and geometric distribution of the Fe-Co phase, all factors that can be tuned with appropriate chemistry and thermal-magnetic annealing.
Here, we report on the results of a high-energy x-ray diffraction study of Al–Pd–Mn to investigate the solidification products obtained during free-cooling using an electrostatic levitation furnace. The primary solidification product from the melt is i-Al–Pd–Mn which coexists with a significant remaining liquid component. As the sample cools further, we find that the solidification pathway is consistent with the liquidus projection and pseudo-binary cut through the ternary phase diagram reported previously. At ambient temperature we have identified the major phase to be the ξ'-phase orthorhombic approximant, along with minor phases identified as Al and, most likely, the R-phase orthorhombic approximant. We have also observed a distinct prepeak in the liquid at high temperature, signifying the presence of extended atomic order. Interestingly, this prepeak was not observed in previous neutron diffraction measurements on the Al–Pd–Mn system. No undercooling was observed preceding the solidification of the i-Al–Pd–Mn phase from the melt which may signal the close similarity of the short-range order in the solid and liquid. However, this can not be clearly determined because of the potential for heterogenous nucleation associated with the presence of an Al2O3 impurity at the surface of the sample.