Engineering topics

Kraft, R. E.

Publications and source records attributed to Kraft, R. E..

24 records · Page 2

NASA NTRS1976

Effects of multi-element acoustic treatment on compressor inlet noise

An analytic and experimental study was conducted with the objective of developing both a basic understanding of axially segmented inlet acoustic treatment liners, and design procedures for enhancing the suppression of compressor inlet radiated noise. Anechoic chamber measurements demonstrated that the multielement treatment produced significantly more low frequency suppression than uniform treatment. Further, in-duct spinning mode patterns generated by the rotating vehicle were successfully measured and used as input to an analytical prediction procedure, providing significant improvement in inlet suppression predictions. The study indicated that phased inlet liners can be designed to provide increased noise suppression compared to uniform treatment.

Kraft, R. E.↗

NASA NTRS1976

Practical considerations for the design of two-element duct liner noise suppressors

The results of analytical and experimental design studies for two-segment treatment configurations in rectangular ducts with mean flow are presented. The practical significance of the design optimization method, executed at a single frequency for measured modal input, is considered in the light of sensitivity to variations in wall impedance components and source modal content. The results of analytical parametric studies of the effects of frequency and segment length ratio are presented. The importance of designing for a measured modal content and the importance of the order of the liners in providing the multi-element suppression enhancement effects are demonstrated.

Kraft, R. E.↗

NASA NTRS1976

Optimization of suppression for two-element treatment liners for turbomachinery exhaust ducts

Sound wave propagation in a soft-walled rectangular duct with steady uniform flow was investigated at exhaust conditions, incorporating the solution equations for sound wave propagation in a rectangular duct with multiple longitudinal wall treatment segments. Modal analysis was employed to find the solution equations and to study the effectiveness of a uniform and of a two-sectional liner in attenuating sound power in a treated rectangular duct without flow (M = 0) and with uniform flow of Mach 0.3. Two-segment liners were shown to increase the attenuation of sound as compared to a uniform liner. The predicted sound attenuation was compared with measured laboratory results for an optimized two-segment suppressor. Good correlation was obtained between the measured and predicted suppressions when practical variations in the modal content and impedance were taken into account. Two parametric studies were also completed.

Motsinger, R. E.↗

NASA NTRS1976

A preliminary in-duct measurement of spinning modes in the inlet of a rotating vehicle

Suppression of noise radiated from a jet engine duct is an important environmental problem. Results are presented for a study aimed at developing and evaluating an experimental method for measuring the complex acoustic pressure field at a plane in the inlet of a fan duct. The theory of modal propagation is outlined and related to the theory of measuring spinning modes in the duct. A spinning mode measurement apparatus is described, and preliminary test results of the modal measurement for several operating speeds are presented. The measurement of spinning modes is successfully carried out in the inlet of a rotating vehicle under conditions representative of an actual jet engine. Data repeatability and problems encountered in the measurement are examined. In particular, it is important to calibrate the probe systems for phase and level. Recommendations for future improvements in the method are made.

Kraft, R. E.↗

NASA NTRS1976

Design of optimum acoustic treatment for rectangular ducts with flow

A design optimization technique for acoustic treatment in rectangular ducts with uniform mean flow is presented. The technique is based on the acoustic wave solution in terms of series of characteristic duct modes. The analysis allows multiple axial treatment sections along the length of the duct and requires a known modal characterization of the sound source. Conditions of acoustic pressure and acoustic velocity continuity are used to match modal solutions at planes of impedance discontinuity in the duct. Experimental techniques for obtaining this modal characterization are presented. Using duct modes measured at the source plane, the optimization technique is exercised to design an optimized single element liner in a case without mean flow, and optimized single and dual element liners in cases with mean flow. The validity of the program for predicting noise suppression is demonstrated by comparing analytical predictions with measured data for several (non-optimum) cases. Application to treatment design in turbomachinery exhaust ducts is considered.

Motsinger, R. E.↗

NASA NTRS1976

Effects of mean flow on duct mode optimum suppression rates

The nature of the solution to the convected acoustic wave equation and associated boundary conditions for rectangular ducts containing uniform mean flow is examined in terms of the complex mapping between the wall admittance and characteristic mode eigenvalues. It is shown that the Cremer optimum suppression criteria must be modified to account for the effects of flow below certain critical values of the nondimensional frequency parameter of duct height divided by sound wavelength. The implications of these results on the design of low frequency suppressors are considered.

Kraft, R. E.↗