Engineering Papers⌕ Search

Engineering topics

Koenig, R. W.

Publications and source records attributed to Koenig, R. W..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Performance of high-altitude, long-endurance, turboprop airplanes using conventional or cryogenic fuels

An analytical study has been conducted to evaluate the potential endurance of remotely piloted, low speed, high altitude, long endurance airplanes designed with 1990 technology. The baseline configuration was a propeller driven, sailplane like airplane powered by turbine engines that used JP-7, liquid methane, or liquid hydrogen as fuel. Endurance was measured as the time spent between 60,000 feet and an engine limited maximum altitude of 70,000 feet. Performance was calculated for a baseline vehicle and for configurations derived by varying aerodynamic, structural or propulsion parameters. Endurance is maximized by reducing wing loading and engine size. The level of maximum endurance for a given wing loading is virtually the same for all three fuels. Constraints due to winds aloft and propulsion system scaling produce maximum endurance values of 71 hours for JP-7 fuel, 70 hours for liquid methane, and 65 hours for liquid hydrogen. Endurance is shown to be strongly effected by structural weight fraction, specific fuel consumption, and fuel load. Listings of the computer program used in this study and sample cases are included in the report.

Liu, G. C.↗
NASA NTRS1979

Preliminary QCGAT program test results

The paper presents the NASA Lewis program to demonstrate that large engine technology can be applied to general aviation engines to reduce noise, emissions, and fuel consumption. After a Phase I study, two contractors, Garrett AiResearch and AVCO-Lycoming, were selected to design, manufacture, assemble, test, and deliver their Quiet, Clean, General Aviation Turbofan (QCGAT) engines to NASA. Noise, emission, and performance goals and how well they were met are discussed. Noise goals involve take off noise 3.5 n. mi. from runway threshold, sideline noise at .25 n mi. and approach noise 1 n mi. from the runway at an altitude of 370 ft. The AiResearch engines power a stretched Learjet 35 and the Lycoming a specially conceived Beech executive jet, resulting in differing power goals. Thus the thrust goal for the Lycoming was 1622 lb. while the AiResearch goal was 3937 lb. Cruise thrust goals were 485 lb. at Mach 0.6 at 25,000 ft. and 903 lb. at Mach 0.8 at 40,000 ft. respectively. The design of both engines, based on existing cores, is studied, noting such special QCGAT features as new reduction gears, combustor and power turbine. Test results are given, indicating that while the goals for noise and thrust were met those for emissions were only partially met.

Koenig, R. W.↗
NASA NTRS1979

Preliminary QCGAT program test results

NASA Lewis Research Center is conducting a program to demonstrate that large commercial engine technology can be applied to general aviation engines to reduce noise, emissions and fuel consumption and to develop new technology where required. The overall engine program, design, and technology incorporated into the QCGAT engines are described. In addition, preliminary engine test results are presented and compared to the technical requirements the engines were designed to meet.

Koenig, R. W.↗
NASA NTRS1973

A simulator investigation of the influence of engine response characteristics on the approach and landing for an externally blown flap aircraft. Part 1: Description of the simulation and discussion of results

Investigation of the influence of engine response characteristics on approach and landing operations of a powered lift aircraft were carried out in a piloted ground-based simulator. The aircraft simulated was a four engine, externally-blown jet-flap configuration having an 80 pound wing loading and .56 thrust to weight ratio. Results indicate that for ideal operating conditions and minimal pilot reaction delay, substantial reductions in engine-out wave-off altitude increment and touchdown sink rate for engine-out landings can be achieved with the fast engine compared to the slow engine response. However, delays in pilot reaction of one to two seconds diminish the advantage of rapid thrust response. A need exists for some form of automatic cueing of the pilot or automatic engine control to enable the potential of rapid thrust response to be realized in improving safety in the event of an engine failure.

Franklin, J. A.↗
NASA NTRS1972

GENENG: A program for calculating design and off-design performance for turbojet and turbofan engines

A computer program entitled GENENG employs component performance maps to perform analytical, steady state, engine cycle calculations. Through a scaling procedure, each of the component maps can be used to represent a family of maps (different design values of pressure ratios, efficiency, weight flow, etc.) Either convergent or convergent-divergent nozzles may be used. Included is a complete FORTRAN 4 listing of the program. Sample results and input explanations are shown for one-spool and two-spool turbojets and two-spool separate- and mixed-flow turbofans operating at design and off-design conditions.

Koenig, R. W.↗
NASA NTRS1972

GENENG 2: A program for calculating design and off-design performance of two- and three-spool turbofans with as many as three nozzles

A computer program which calculates steady-state design and off-design jet engine performance for two- or three-spool turbofans with one, two, or three nozzles is described. Included in the report are complete FORTRAN 4 listings of the program with sample results for nine basic turbofan engines that can be calculated: (1) three-spool, three-stream engine; (2) two-spool, three-stream, boosted-fan engine; (3) two-spool, three-stream, supercharged-compressor engine; (4) three-spool, two-stream engine; (5) two-spool, two-stream engine; (6) three-spool, three-stream, aft-fan engine; (7) two-spool, three-stream, aft-fan engine; (8) two-spool, two-stream, aft-engine; and (9) three-spool, two-stream, aft-fan engine. The simulation of other engines by using logical variables built into the program is also described.

Fishbach, L. H.↗
NASA NTRS1972

STOL propulsion systems

The selection and the characteristics of quiet, clean propulsion systems for STOL aircraft are discussed. Engines are evaluated for augmentor wing and externally blown flap STOL aircraft with the engines located both under and over the wings. Some supporting test data are presented. Optimum engines are selected based on achieving the performance, economic, acoustic, and pollution goals presently being considered for future STOL aircraft. The data and results presented were obtained from a number of contracted studies and some supporting NASA inhouse programs, most of which began in early 1972. The contracts include: (1) two aircraft and mission studies, (2) two propulsion system studies, (3) the experimental and analytic work on the augmentor wing, and (4) the experimental programs on Q-Fan. Engines are selected and discussed based on aircraft economics using the direct operating cost as the primary criterion. This cost includes the cost of the crew, fuel, aircraft, and engine maintenance and depreciation.

Denington, R. J.↗