Engineering Papers⌕ Search

Engineering topics

Koch, C. C.

Publications and source records attributed to Koch, C. C..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

The effect of composition and cooling rate on the structure of rapidly solidified (Fe, Ni)3Al-C alloy

The quench rate-metastable structure dependence in the Fe-20Ni-8Al-2C wt pct alloy has been experimentally studied. The nonequilibrium gamma-prime and gamma phases were noted in foils 65-100 microns thick, while at higher quench rates (thinner samples) the matrix was found to be in a disordered fcc gamma phase with kappa carbide precipitates. With the addition of silicon to the alloys, the nonequilibrium gamma-prime and gamma structures are observed at higher cooling rates.

Myers, S. A.↗
NASA NTRS1989

High-temperature ordered intermetallic alloys III; Proceedings of the Third Symposium, Boston, MA, Nov. 29-Dec. 1, 1988

The present conference on high-temperature ordered intermetallic alloys discusses alloy theory and phase stability, defects and microstructures, mechanical behavior, alloy design and material processing, multiphase and composite materials, nickel aluminides, titanium aluminides, and other ordered intermetallics. Attention is given to compositional effects on processing and properties of nickel aluminides, dynamic compaction and hot-isostatic-pressing of nickel aluminides, improvement of elevated-temperature material properties in Ni3Al, the effect of microalloying B on the high-temperature mechanical properties of Ti3Al, the effects of structure on creep of Ti-53.4 mol pct Al intermetallics, the deformation microstructure in Ni3Si polycrystals strained over the range of temperature of flow stress anomaly, and the microstructure and mechanical properties of dual phase alloys consisting of the intermetallic phases.

Liu, C. T.↗
NASA NTRS1987

High-temperature ordered intermetallic alloys II; Proceedings of the Second Symposium, Boston, MA, Dec. 2-4, 1986

The papers presented in this volume provide on overview of recent theoretical and experimental research in the field of high-temperature ordered intermetallic alloys. The papers are gouped under the following headings: ordering behavior and theory, microstructures, mechanical behavior, alloy design and microstructural control, and metallurgical properties. Specific topics discussed include antiphase domains, disordered films and the ductility of ordered alloys based on Ni3Al; kinetics and mechanics of formation of Al-Ni intermetallics; deformability improvements of L1(2)-type intermetallic compounds; B2 aluminides for high-temperature applications; and rapidly solidified binary TiAl alloys.

Stoloff, N. S.↗
NASA NTRS1986

Testing techniques for mechanical characterization of rapidly solidified materials

Mechanical property testing techniques are reviewed for rapidly solidified materials. Mechanical testing of rapidly solidified materials is complicated by the fact that in most cases at least one dimension of the material is very small (less than 100 microns). For some geometries, i.e., powder or thin surface layers, microhardness is the only feasible mechanical test. The ribbon geometry which is obtained by the melt-spinning method, however, has been used for a variety of mechanical property measurements including elastic properties, tensile properties, fracture toughness, creep, and fatigue. These techniques are described with emphasis placed on the precautions required by the restricted geometry of rapidly solidified specimens.

Koch, C. C.↗
NASA NTRS1985

A review of rapid solidification studies of intermetallic compounds

A review of rapid solidification studies of high-temperature ordered intermetallic compounds is presented. Emphasis is on the nickel - and iron- aluminides which are of potential interest as structural materials. The nickel-base aluminides which have been rapidly solidified exhibit changes in grain size, compositional segregation, and degree of long range order (as reflected in APB size and distribution) which markedly affect mechanical properties. Some experiments indicate the formation of a metastable L1(2) phase in rapidly solidified Fe-(Ni,Mn)-Al-C alloys, while other work observes only a metastable fcc phase in the same composition range. The metastable phases and/or microstructures in both nickel and iron aluminides are destroyed by annealing at temperatures above 750 K, with subsequent degradation of mechanical properties. Rapid solidification studies of several other intermetallic compounds are briefly noted.

Koch, C. C.↗
NASA NTRS1982

Energy efficient engine. High pressure compressor detail design report

A compressor optimization study defined a 10-stage configuration with a 22.6:1 pressure ratio, and adiabatic efficiency goal of 86.1%, and a polytropic efficiency of 90.6%; the corrected airflow is 53.5 kg/sec. Subsequent component testing included three full-scale tests: a six-stage rig test, and another 10-stage rig test completed in the second quarter of 1982. Information from these tests is being used to select the configuration for a core engine test scheduled for July 1982 and an integrated core/low spool test slated for early 1983. The test results will also provide data base for the flight propulsion system.

Holloway, P. R.↗
NASA NTRS1978

Energy efficient engine: Preliminary design and integration studies

Parametric design and mission evaluations of advanced turbofan configurations were conducted for future transport aircraft application. Economics, environmental suitability and fuel efficiency were investigated and compared with goals set by NASA. Of the candidate engines which included mixed- and separate-flow, direct-drive and geared configurations, an advanced mixed-flow direct-drive configuration was selected for further design and evaluation. All goals were judged to have been met except the acoustic goal. Also conducted was a performance risk analysis and a preliminary aerodynamic design of the 10 stage 23:1 pressure ratio compressor used in the study engines.

Johnston, R. P.↗
NASA NTRS1977

Preliminary design study of advanced multistage axial flow core compressors

A preliminary design study was conducted to identify an advanced core compressor for use in new high-bypass-ratio turbofan engines to be introduced into commercial service in the 1980's. An evaluation of anticipated compressor and related component 1985 state-of-the-art technology was conducted. A parametric screening study covering a large number of compressor designs was conducted to determine the influence of the major compressor design features on efficiency, weight, cost, blade life, aircraft direct operating cost, and fuel usage. The trends observed in the parametric screening study were used to develop three high-efficiency, high-economic-payoff compressor designs. These three compressors were studied in greater detail to better evaluate their aerodynamic and mechanical feasibility.

Wisler, D. C.↗
NASA NTRS1972

Evaluation of range and distortion tolerance for high Mach number transonic fan stages. Task 2: Performance of a 1500-foot-per-second tip speed transonic fan stage with variable geometry inlet guide vanes and stator

A 0.5 hub/tip radius ratio compressor stage consisting of a 1500 ft/sec tip speed rotor, a variable camber inlet guide vane and a variable stagger stator was designed and tested with undistorted inlet flow, flow with tip radial distortion, and flow with 90 degrees, one-per-rev, circumferential distortion. At the design speed and design IGV and stator setting the design stage pressure ratio was achieved at a weight within 1% of the design flow. Analytical results on rotor tip shock structure, deviation angle and part-span shroud losses at different operating conditions are presented. The variable geometry blading enabled efficient operation with adequate stall margin at the design condition and at 70% speed. Closing the inlet guide vanes to 40 degrees changed the speed-versus-weight flow relationship along the stall line and thus provided the flexibility of operation at off-design conditions. Inlet flow distortion caused considerable losses in peak efficiency, efficiency on a constant throttle line through design pressure ratio at design speed, stall pressure ratio, and stall margin at the 0 degrees IGV setting and high rotative speeds. The use of the 40 degrees inlet guide vane setting enabled partial recovery of the stall margin over the standard constant throttle line.

Bilwakesh, K. R.↗