Engineering Papers⌕ Search

Engineering topics

Knox, Hunter

Publications and source records attributed to Knox, Hunter.

35 records · Page 2

EGS Collab Experiment 1 Stimulation Data

Stimulation data from Experiment 1 of EGS Collab, which occurred on the 4850 ft level of the Sanford Underground Research Facility (SURF). A detailed description of the stimulation data is provided in the StimulationDataNotes.docx and is also available on the EGS Collab Wiki. A Meta Data Cheat Sheet, which describes all of the channels in the Raw CSV files, is available as well. Note that this cheat sheet is a comprehensive meta data descriptor and channels were added as the experiment evolved. This means that some columns may not be populated in early data. Additionally, we have included the chat logs from these experiments. The experiments were broadcast over teleconferencing software and real-time data displays were available to remote observers. The logs contain important observations from those personnel performing the experiment and the remote contributors. Finally, we have included summary and individual plots of all of the data for the user to compare to.

15 GEOTHERMAL ENERGY↗

Field Test Bed for Vadose-Zone Monitoring Approaches - 20404

In the Central Plateau at the U.S. Department of Energy Hanford Site, a large inventory of contaminants resides in unsaturated sediments within the approximately 100-meter-thick vadose zone, posing a potential continuing risk to groundwater. Vadose zone remedies used to address these contaminants will require performance monitoring to provide feedback during implementation and for long-term verification that remedial action objectives have been met. Passive approaches may also need long-term monitoring to demonstrate that the flux of contaminants from the vadose zone to the groundwater are below thresholds established to meet groundwater protection goals. Collection of physical (e.g., groundwater or sediment) samples is a common method for identifying contaminant concentration distributions, but this approach is limited by the number of locations and the frequency with which data can be collected. In situ vadose zone measurements have evolved over the past few years to include key measurements of water content, soil water pressure, temperature, and chemical concentration. However, the current generation of sensors is designed for relatively short-term use in near-surface soils or sediments. Geophysical methods have been evolving but are also limited in that they have not been designed for the specific long-term vadose zone monitoring needs at the Hanford Site. Overall, monitoring under unsaturated conditions can be difficult due to the need to install and maintain instrumentation over a large area and depth and the need to identify preferential flow pathways due to geologic and chemical heterogeneities over long periods. Thus, a vadose zone monitoring test bed was initiated to address these challenges and identify cost-effective approaches for implementation and postclosure monitoring of the deep vadose zone. The monitoring test bed is expected to provide valuable field-scale information for the design of vadose zone monitoring systems. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

EGS Collab Experiment 1: 3D Seismic Velocity Model and Updated Microseismic Catalog from Double-Difference Seismic Tomography

This package contains a 3D Seismic velocity model and an updated microseismic catalog obtained for a double-difference seismic tomography study. The 3D_seismic_velocity_model text file contains x (m), y(m), z(m), P-wave velocity (km/s), P-wave velocity quality indicator (1 for well-constrained; 0 for poorly constrained), S-wave velocity (km/s), and S-wave velocity quality indicator (1 for well-constrained; 0 for poorly constrained). The Updated_MEQ_catalog text file contains event origin time, x(m), y(m), z(m), error in x (m), error in y (m), error in z (m), and RMS misfit (millisecond). The 3D_seismic_P-wave_velocity_model animation file shows slices of the 3D P-wave velocity model. The 3D_seismic_S-wave_velocity_model animation file shows slices of the 3D S-wave velocity model. The Interactive_MEQ_location_comparison API file is an interactive visualization of the updated microseismic event locations and the original seismic catalog. The visualization allows users to view and compare the event locations by dragging, rotating, and zooming in. An updated version of 3D_seismic_velocity_model and associated animations were included, which were calculated with a more strict assumption for quality indicators.

15 GEOTHERMAL ENERGY↗

Near-Field Imaging of Shallow Chemical Explosions in Granite Using Change Detection Methods with Surface and Borehole Seismic Data

Explosions detonated in geologic media damage it in various ways via processes that include vaporization, fracturing, crushing of interstitial pores, etc. Seismic waves interact with the altered media in ways that could be important to the discrimination, characterization, and location of the explosions. As part of the Source Physics Experiment, we acquired multiple pre- and post-explosion near-field seismic datasets and analyzed changes to seismic P-wave velocity. Our results indicate that the first explosion detonated in an intact media can cause fracturing and, consequently, a decrease in P-wave velocity. After the first explosion, subsequent detonations in the pre-damaged media have limited discernible effects. We hypothesize this is due to the stress-relief provided by a now pre-existing network of fractures into which gasses produced by the explosion migrate. We also see an overall increase in velocity of the damaged region over time, either due to a slow healing process or closing of the fractures by subsequent explosions.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Slip Tendency Analysis of Fracture Networks to Determine Suitability of Candidate Testbeds for the EGS Collab Hydroshear Experiment

Experiment 2 of the EGS Collab project is aimed at testing stimulation by hydro-shearing of existing natural fractures, versus Experiment 1, which is focused on hydraulic fracturing a rock mass to enhance permeability. The main criterion for the testbed selection in Experiment 2 is the presence of an interconnected network of fractures, at least 10 meters in extent, and with orientations such that shear slip can be induced at injection pressures less than the minimum horizontal stress (Shmin). The feasibility analysis for this experiment requires a well-constrained stress state along with well-characterized fracture networks. The fracture systems at two candidate locations in the Sanford Underground Research Facility (SURF), the 4850 Level (number refers to depth below ground surface in feet) and the 4100 Level, have been characterized to different extents. The 4850 Level has a well-characterized Discrete Fracture Network (DFN) from borehole (drilled for an experimental test bed) and drift observations. In contrast, the 4100 level has a fracture network characterized only by observations from the drift wall, which provides little constraint on fracture extents. This paper will present assessments for the interpreted slip potential for the natural fractures at the two locations. Data uncertainties are addressed by performing a probabilistic analysis that takes into account the uncertainty in the stress state, uncertainty in the fracture properties, and preliminary borehole locations. There is strong evidence of shear stimulation of some natural fractures in Experiment 1 on the 4850 level. We use examples of natural fractures strongly linked to shear stimulation in Experiment 1 from multiple monitoring indicators to test the consistency of the stress model and guide the uncertainty interpretation. This analysis is intended to guide the site selection process for Experiment 2 by highlighting the fracture orientations that are likely to be shear-stimulated in a majority of modeled realizations.

15 GEOTHERMAL ENERGY↗

EGS Collab Experiment 1: Microseismic Monitoring

The U.S. Department of Energy's Enhanced Geothermal System (EGS) Collab project aims to improve our understanding of hydraulic stimulations in crystalline rock for enhanced geothermal energy production through execution of intensely monitored meso-scale experiments. The first experiment is being performed at the 4850 ft level of the Sanford Underground Research Facility (SURF), approximately 1.5 km below the surface at Lead, South Dakota. Here we report on microseismic monitoring of repeated stimulation experiments and subsequent flow tests between two boreholes in the Poorman Formation. Stimulations were performed at several locations in the designated injection borehole at flow rates from 0.1 to 5 L/min over temporal durations from minutes to hours. Microseismic monitoring was performed using a dense 3D sensor array including two cemented hydrophone strings with 12 sensors at 1.75 m spacing accompanied by 18 3-C accelerometers, deployed in 6 monitoring boreholes, completely surrounding the stimulation region. Continuous records were obtained over a two-month period using a novel dual recording system consisting of a conventional 96 channel exploration seismograph and a high-performance 64 channel digitizer sampling sensors at 4 and 100 kHz respectively. Using a standard STA/LTA triggering algorithm, we detected thousands of microseismic events with recorded energy in a frequency range generally above 3 kHz and up to 40 kHz. The locations of these events are consistent with creation of a hydraulic fracture and additional reactivation of pre-existing structures. Using manual pick refinement and double-difference relocation we are able to track the fracture growth to high precision. We estimate the times and locations of the fracture intersecting a monitoring and the production borehole using microseismic events. They are in excellent agreement with independent measurements using distributed temperature sensing, in-situ strain observations and measurements of conductivity changes. This submission includes a microearthquake catalog, raw event files, a subset of the continuous microseismic monitoring data collected during stimulations and flow test activity on 05/22/2018, 05/23/2018, 05/24/2018, 05/25/2018, 06/25/2018, 07/19/2018, 07/20/2018, 12/7/2018, 12/20/2018, and 12/21/2018 (in binary format), and a binary file interpreter to read the continuous microseismic monitoring data. A Stanford Geothermal Workshop paper is also included to describe microseismic monitoring activities at SURF during these periods.

15 GEOTHERMAL ENERGY↗

EGS Collab Experiment 1: Circulation Testing

These data and test descriptions comprise a chilled circulation test conducted at the 164' fracture in the EGS Collab Experiment 1 testbed on the 4850 ft level of the Sanford Underground Research Facility. Descriptions of the meta data, design drawings for the flow testing system, and evaluation of the thermistor data are provided here. The test ran from April 2019 through early March of 2020, when testing was concluded at the experiment 1 site. These data are are complementary to the stimulation data provided in another submission which is linked below (i.e. stimulation at the 164' notch). More information about the test itself as well as the rationale and process of data processing is available on the EGS Collab Experiment 1 Long Term Circulation Test wiki page which is also linked below.

15 GEOTHERMAL ENERGY↗

EGS Collab Project Electrical Resistivity Tomography Characterization and Monitoring

The EGS (Enhanced Geothermal Systems) Collab project is performing stimulation experiments in highly monitored and well-characterized intermediate-scale (~10-20 m) field test beds. The characterization and monitoring system includes an array of electrodes grouted in place within six monitoring wells, with 16 electrodes per well. The electrodes enable characterization of the 3D low-frequency electrical properties of the host rock, and changes in those properties during stimulation and tracer testing using both static and time-lapse Electrical Resistivity Tomography. In this talk we present: 1) ERT array design and installation, 2) baseline (pre-stimulation) imaging results, 3) time-lapse data collected during stimulation operations, and 4) real-time imaging during clean water injections intended to illuminate flow paths as a decrease in bulk electrical conductivity. We will also discuss aspects and lessons learned for conducting ERT imaging operations in the presence of high fluid pressure gradients during stimulation and flow operations. Results to date reveal a highly heterogeneous rock fabric, ranging over four orders of magnitude in bulk electrical conductivity, and high polarization capacity. Baseline imaging results are consistent with borehole logs and core studies. Time-lapse imaging results to identify major flow paths during tracer studies are forthcoming and will be discussed during this presentation. Ultimately the ERT imaging data sets provide useful information for validating and verifying model predictions in preparation for research at DOE’s Frontier Observatory for Research in Geothermal Energy (FORGE).

electrical resistivity tomography, geophysics, geo↗

EGS Collab Project Experiment 1 Overview and Progress

Enhanced Geothermal Systems (EGS) offer the potential to extract and use large quantities of clean energy, but questions remain on reservoir creation and sustainability. The EGS Collab project, supported by the US Department of Energy’s Geothermal Technologies Office, is establishing a suite of highly monitored and well-characterized intermediate-scale (~10-20 m) field test beds along with fracture stimulation and interwell flow tests to better understand processes that control formation of effective subsurface heat exchangers. EGS Collab tests will provide a means of testing tools and concepts that could later be employed under geothermal reservoir conditions at DOE’s Frontier Observatory for Research in Geothermal Energy (FORGE) or enhanced geothermal systems. Key to the project is using numerical simulations in the experiment design and interpretation of results. Our first set of experiments is underway at the Sanford Underground Research Facility (SURF) in South Dakota. To date, stepwise stimulations have been performed at two locations, with the final stimulation connecting our injection and production wells. Numerous data have been collected and are currently being analyzed.

Enhanced Geothermal Systems, EGS Collab, Stimulati↗

The EGS Collab Hydroshear Experiment at the Sanford Underground Research Facility – Siting Criteria and Evaluation of Candidate Sites

The objective of the EGS Collab project is to establish a suite of intermediate-scale (~10-20 m) field test beds coupled with stimulation and interwell flow tests to provide a basis to better understand fracture stimulation methods, resulting fracture geometries, and processes that control heat transfer between rock and stimulated fractures. Experiment 1 of the project is being conducted at a depth of ~1.5 km in the Sanford Underground Research Facility (SURF) on the 4850 Level (ft. below the ground surface). The stimulation method planned for Experiment 2 of this project is hydroshearing of an existing natural fracture. In siting this experiment, there are several key geologic criteria that need to be met. These include: 1) the fracture should be least 10 m in length so that it could be intersected by two boreholes that are spaced that far apart; 2) it should be optimally oriented relevant to the stress field so that it is critically stressed; 3) the site should have appropriate stress conditions (not too shallow a depth); 4) the fracture should have sufficient permeability to allow for prestimulation flow testing, but not too high a permeability that would preclude permeability enhancement via shear stimulation; 5) the fracture should not intersect other features (permeable fractures, boreholes, adjacent drifts) that could serve as major leak-off zones; 6) the site should not be complicated by geology (a single lithology would be preferred). In addition, there are logistical criteria that will also influence site selection, including: 1) site availability/access, 2) logistical support, e.g., power, internet, water, operating rail system; 3) drift size and orientation compatible with drilling and site operations; 4) appropriate ground support. There are only two deep levels at SURF that can be accessed by the Yates Shaft: the 4100 and the 4850, so we limited our search to these two levels. Currently, three candidate sites are being evaluated: the existing Experiment 1 site and its surroundings on the West Drift on the 4850 level, and two locations on the 4100 level. This paper will evaluate advantages, disadvantages, and risks associated with these three options at SURF.

EGS Collab, Sanford Underground Research Facility↗

The EGS Collab Project: Stimulation and Simulation

Development of Enhanced Geothermal Systems (EGS) requires accurate predictions of flow rates and temperatures at production wells over time. The concept of EGS is simple; however, complications from heterogeneity and complexity of fracture pathways may lead to channeling, short-circuiting, and premature thermal breakthrough. In the EGS Collab project, we are establishing a suite of highly monitored and well characterized intermediate-scale (~10-20 m) field test beds along with fracture stimulation and interwell flow tests to better understand processes that control formation of effective subsurface heat exchangers. EGS Collab experiments will provide a means of testing tools and concepts that could later be employed under geothermal reservoir conditions at FORGE or elsewhere. Key to the project is using numerical simulations in the experiment design and interpretation of results. Our tests will be well-controlled, in situ experiments focused on rock fracture behavior and permeability enhancement. Our pre- and post-test modeling results of each field experiment compared with detailed measurements will allow for improved model prediction and validation. We will use comprehensive instrumentation to collect high-quality and high-resolution geophysical and other fracture characterization and fluid flow data. We will analyze these data and compare them with models and field observations to further elucidate the basic relationships between stress, induced seismicity, and permeability enhancement. We will also observe and quantify other key governing parameters that impact permeability, and will attempt to understand how these parameters might change throughout the development and operation of an EGS project with the ultimate goal of enabling commercial viability of EGS. Our first set of experiments will be performed at the Sanford Underground Research Facility (SURF) in South Dakota. Our team is well underway with building the first field experiment test bed planned for this project, which is supported by the US Department of Energy’s Geothermal Technologies Office.

EGS Collab↗

An Overview of the EGS Collab Project: Field Validation of Coupled Process Modeling of Fracturing and Fluid Flow at the Sanford Underground Research Facility, Lead, SD

Enhanced Geothermal Systems (EGS) development will require an ability to accurately predict the flow rates and temperatures of the production wells. While simple in concept, complex heterogeneous fracture pathways can lead to channeling, short-circuiting, and premature thermal breakthrough complicating EGS. The EGS Collab project will establish a suite of intermediate-scale (~10-20 m) field test beds coupled with stimulation and interwell flow tests to provide a basis to better understand the fracture geometries and processes that control heat transfer between rock and stimulated fractures. These experiments will provide a means of testing tools, codes, and concepts that could later be employed under geothermal reservoir conditions at FORGE and in EGS. We will perform well-controlled, in situ experiments focused on rock fracture behavior and permeability enhancement. Pre- and post-test modeling of each test will allow for model prediction and validation. Comprehensive instrumentation will be used to collect high-quality, high-resolution geophysical and fracture characterization and fluid flow data. ,These data will be analyzed and compared with models and field observations to further elucidate the basic relationships between stress, induced seismicity, and permeability enhancement. To the maximum extent achievable, we will observe and quantify other key governing parameters that impact permeability, and attempt to understand how these parameters might change throughout the development and operation of an EGS project with the goal of enabling commercial viability of EGS. The Sanford Underground Research Facility (SURF) in South Dakota was selected as the EGS Collab project experimental site based on the evaluation of information from several sites. Our team has designed and constructed the first field experiment planned for this project, which is supported by the US Department of Energy’s Geothermal Technologies Office.

EGS, FORGE, field fracture stimulation and flow ex↗

Fracture and Flow Designs for the Collab/SIGMA-V Project

The first experiment of the Enhanced Geothermal Systems (EGS) Collab (a.k.a Stimulation Investigations for Geothermal Modeling Analysis and Validation (SIGMA-V)) project is designed to comprehensively monitor a series of hydraulic fracture stimulations and subsequent flow tests. This experiment is planned for the 4850 Level in the Sanford Underground Research Facility (SURF), located at the former Homestake Gold Mine, in Lead, South Dakota. The target host rock for these stimulations and flow tests is a phyllite schist known as the Poorman formation. This paper discusses at a high level the engineering design for the stimulation and fracture monitoring system, the considerations for the test bed construction, and the preliminary stimulation modeling. Furthermore, this paper will highlight the intricate ways that predictive modeling can be used for testbed and stimulation design. This project is funded by the United States Department of Energy, Geothermal Technologies Office (GTO).

Knox, Hunter↗

Adaptive Self Tuning

The AST software includes numeric methods to 1) adjust STA/LTA signal detector trigger level (TL) values and 2) filter detections for a network of sensors. AST adapts TL values to the current state of the environment by leveraging cooperation within a neighborhood of sensors. The key metric that guides the dynamic tuning is consistency of each sensor with its nearest neighbors: TL values are automatically adjusted on a per station basis to be more or less sensitive to produce consistent agreement of detections in its neighborhood. The AST algorithm adapts in near real-time to changing conditions in an attempt to automatically self-tune a signal detector to identify (detect) only signals from events of interest.

Peterson, Matthew↗