Engineering Papers⌕ Search

Engineering topics

Kloužek, Jaroslav

Publications and source records attributed to Kloužek, Jaroslav.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Boron nitride: Novel ceramic reductant for low‐activity waste vitrification

Abstract During vitrification of radioactive wastes, excessive foaming reduces processing rates within melters by hindering heat transfer from the molten glass pool to the reacting melter feed. Formulations of low‐activity waste (LAW) melter feeds, for vitrification at the Waste Treatment and Immobilization Plant at the Hanford Site, conventionally include the addition of sucrose to mitigate excessive foaming by hastening the denitration process. However, incomplete combustion of sucrose produces organics such as acetonitrile (C 2 H 3 N) that may exceed bounding limits of downstream effluent treatment facilities. Using boron nitride (BN) as an alternate reductant to sucrose, in a representative LAW melter feed reduced C 2 H 3 N production by 90% by preventing the low‐temperature sucrose–nitrate reactions. Furthermore, foaming was suppressed due to the higher decomposition temperature of BN than H 3 BO 3 meaning a delayed reaction of a large fraction of boron with the transient glass‐forming melt until above the foam onset temperature, thus reducing the quantity and viscosity of the connected melt and trapping less gas in the foam layer.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Viscosity of transient glass-forming melt and its relation to foaming during batch-to-glass conversion

Primary foam, which affects the heat transfer into the glass batch and the final glass quality, occurs when a sufficient quantity of transient glass-forming melt evolves with viscosity low enough to close the open porosity of the reacting glass batch. To better understand how the fraction of transient melt and its viscosity affect the primary foam temperature range, we determined, with x-ray diffraction, the fraction and composition of the transient glass-forming melt in a heated waste glass melter feed as a function of temperature. Then we prepared a set of transient melts that occurred within the foaming temperature interval and measured their viscosities with spindle and falling sphere viscometers. Further, the results agree with the Adam-Gibbs and VFT viscosity-composition models, even for transient melt compositions outside of the models compositional validity range. As silica and other refractory particles dissolved in the predominantly borate transient melt while temperature increased, viscosity increased from the initial value of ~500 Pa s at the onset of foaming (~650°C) to a maximum of ~770 Pa s when silica dissolution was almost complete (~700°C). As temperature increased further, transient melt viscosity decreased to ~220 Pa s (~850°C) when the primary foam collapsed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of glass forming additives on low-activity waste feed conversion to glass

A significant effort was invested in the past to develop and refine mathematical models that relate the composition of nuclear waste glasses with their properties, such as viscosity, electrical conductivity, or chemical durability. However, less attention has been paid to the formulation of the melter feed itself, such as the chemical form and the particle size of the glass forming and modifying additives (GFMA), which have a significant effect on the feed-to-glass conversion process during melting. To address this issue, we systematically changed the mineral composition of a simulated low-activity waste melter feed and inspected its melting behavior. When substituting minerals with corresponding oxides and hydroxides, we found that different alumina sources (kyanite, gibbsite, boehmite, or corundum) had the strongest effect on the feed melting process, whereas the sources of Ca, Mg, and Zr had little effect. Further, the x-ray diffraction analysis showed that the alumina sources differ in their dissolution kinetics: early dissolving alumina sources, such as gibbsite (Al(OH) 3 ) and boehmite (AlO(OH)), increase the transient glass-forming melt viscosity at early stages, when gases still evolve, causing extended foaming, whereas alumina sources that dissolve at high temperatures, such as kyanite (Al 2 SiO 5 ) and corundum (Al 2 O 3 ), keep the transient glass-forming melt viscosity low and lead to a faster foam collapse. Using viscosity-composition relationship to estimate the viscosity of transient glass-forming melts in the primary foaming range, we found that the primary foam began to collapse at 360 to 800 Pa s, and fully collapsed between 65 and 260 Pa s. This result agrees with our previous studies, according to which the glass-forming melt viscosity at the cold cap foam bottom ranged from 24 to 85 Pa s.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Effect of feed composition on the production of off-gases during vitrification of simulated low-activity nuclear waste

During the vitrification of nuclear waste, hazardous and radioactive emissions are generated from the feed-to-glass conversion reactions, in addition to discharges from forced air bubbling and air inleakage. Although the major gaseous emissions are water vapor, nitrogen, and carbon dioxide, various monitored environmental pollutants are also released, such as nitrogen oxides or sulfur dioxide. In addition, reactions between organics and nitrates in the feed may also form products of incomplete combustion such as carbon monoxide and acetonitrile. Although off-gas emissions are commonly measured during both laboratory- and pilot-scale melter testing, no predictive tool is currently available to a priori estimate the composition of gaseous emissions during nuclear waste vitrification. This work forms a basis for the development of such predictive tool by measuring gas evolution from a broad range of simulated low-activity waste melter feeds using evolved gas analysis data and developing correlations between the feed and off-gas compositions. Using reaction stoichiometry and regression analysis, we demonstrate that next to the content of nitrogen and organic carbon in the feed, the gaseous emissions are affected by the feed reduction-oxidation conditions – the more the feed is reduced, the less nitrogen monoxide, and more carbon monoxide and acetonitrile evolves. In conclusion, the results presented in this work provide a first step towards reducing the amount of expensive physical melter testing and the regression analysis provides a simple tool for rapid optimization of feed composition with respect to off-gas composition.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Cold-cap structure in a slurry-fed electric melter

We report as glass batch is charged into an electric melter, a cold cap forms on the glass melt surface. Heat transfer to the cold cap from the molten glass below and the melter atmosphere above determines the melting rate. A mathematical model of the cold cap and the experimental kinetic data of the feed-to-glass conversion that were collected for several simulated low-activity and high-level waste melter feeds allowed us to develop relationships between the internal structure of the cold cap, its properties, its thickness, and the internal heat transfer. This contribution shows the distribution of major crystalline phases and the cumulative evolution of gases within the cold cap. It also examines the temperature, conversion degree, and heating rate the melter feed is experiencing during the passage through the cold cap and their effects on the cold-cap bottom temperature and morphology, which are important for the computational fluid dynamics simulations of melters.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of material properties on batch‐to‐glass conversion kinetics

Abstract A recently developed model of the cold cap—the reacting glass batch (melter feeds) floating on molten glass in an electric glass melter—couples heat transfer with the feed‐to‐glass conversion kinetics. The model allows for determining the distributions of temperature and various properties within the cold cap. In the present study, this model is applied to four melter feeds designed for high‐level and low‐activity nuclear wastes. Profiles of temperature, conversion degree, cold cap porosity and density, condensed matter velocity, and heating rate were determined using the material properties of the cold cap. Effects of vigorous foaming at the cold cap bottom were considered. Density, thermal conductivity, and glass production rate strongly affect the cold cap thickness and the fraction of undissolved silica entering the melt under the cold cap. The heating rate profile in the cold cap is highly nonlinear, with high heating rates observed in the foam layer.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Alternative reductants for foam control during vitrification of high-iron High Level Waste (HLW) feeds

Foaming during vitrification of radioactive waste in Joule-Heated Ceramic Melters (JHCM) is exacerbated by trapping of evolving gases, such as CO 2 , NO x and O 2 , beneath a viscous reaction layer. Foaming restricts heat transfer during melting. Sucrose is employed as the baseline additive at the Hanford site in Washington State, USA to reduce foaming. Alternative carbon-based reductant additives were explored in simulated, inactive Hanford high-iron HLW-NG-Fe2 feeds, for both their effect on foaming and to give insight to the behaviour of multivalent species in glass melts under different redox conditions. Graphite, coke (93% C), formic acid and HEDTA additives were compared with sucrose, and a feed with no additive. Graphite and coke additions proved most effective in reducing the maximum foam volume by 51 ± 3% and 54 ± 2%, respectively, compared with 24 ± 5% for sucrose. Lower foaming could result in more efficient vitrification in JHCMs. Reductants also affected redox ratios in the multivalent species present in the feed. The order of reduction, Mn 3+ /Mn 2+ > Cr 6+ /Cr 3+ > Ce 3+ /Ce 4+ > Fe 3+ /Fe 2+ was as predicted on the basis of their redox potentials. There is less reduction overall, particularly in the Fe 3+ → Fe 2+ , than predicted by the calculations, attributed to the oxygenated atmosphere of the experiments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of sucrose on the oxidation-reduction conditions and retention of rhenium during vitrification of low-activity waste

Technetium speciation and solubility during nuclear waste vitrification are affected by oxygen partial pressure in the melt. Thus, reducing agents such as sucrose, which are routinely added to nuclear waste feeds to repress foaming, can significantly affect the volatilization of Tc and increase its retention in glass. Using Re as a surrogate for Tc, we measured the effect of sucrose addition to two low-activity waste melter feeds on the Re retention, oxygen partial pressure, and iron redox as functions of temperature. As expected, Re retention in glass increased as the sucrose content increased. Furthermore, this is attributed to sucrose reaction with nitrates and nitrites in the feed. Destruction of nitrates and nitrites reduces the salt phase fraction and thus likely promotes Re diffusion into the glass-forming melt. In agreement with available literature, we discuss that a modest increase in the sucrose content (compared to current practice) can significantly improve the Tc retention without reducing Fe 2+ to metal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of network connectivity on behavior of synthetic Broborg hillfort glasses

There is wide industrial interest in developing robust models of long-term (>100 years) glass durability. Archeological glass analogs, glasses of similar composition, and alteration conditions to those being tested for durability can be used to evaluate and inform such models. Two such analog glasses from a 1500-year-old vitrified hillfort near Uppsala, Sweden have previously been identified as potential analogs for low concentration Fe-bearing aluminosilicate nuclear waste glasses. However, open questions remain regarding the melting environment from which these historic glasses were formed and the effect of these conditions on their chemical durability. A key factor to answering the previous melting and durability questions is the redox state of Fe in the starting and final materials. Past work has shown that the melting conditions of a glass-forming melt may influence the redox ratio value (Fe +3 /ΣFe), a measure of a glass's redox state, and both melting conditions and the redox ratio may influence the glass alteration behavior. Synthetic analogs of the hillfort glasses have been produced using either fully oxidized or reduced Fe precursors to address this question. In this study, the melting behavior, glass transition temperature, oxidation state, network structure, and chemical durability of these synthesized glass analogs is presented. Resulting data suggests that the degree of network connectivity as impacted by the oxidation state of iron impacted the behavior of the glass-forming melt but in this case does not affect the chemical durability of the final glass. Glasses with a lower degree of melt connectivity were found to have a lower viscosity, resulting in a lower glass transition temperature and softening temperature, as well as in a lower temperature of foam onset and temperature of foam maximum. This lower degree of network connectivity most likely played a more significant role in accelerating the conversion of batch chemicals into glass than the presence of water vapor in the furnace's atmosphere. Future work will focus on using the results from this work with outcomes from other aspects of this project to evaluate long-term glass alteration models.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Conversion degree and heat transfer in the cold cap and their effect on glass production rate in an electric melter

A predictive model of melt rate in waste glass vitrification operations is needed to inform melter operations during normal and off-normal operations. This paper describes the development of a model of the cold cap (the reacting melter feed floating on molten glass in a glass melter) that couples heat transfer with the feed-to-glass conversion kinetics. The model was applied to four melter feeds designed for high-level and low-activity nuclear waste feeds using the material properties, either measured or estimated, to obtain temperature and conversion distribution within the cold cap. The cold cap model, when coupled with a computational fluid dynamics model of a Joule-heated glass melter, allows the prediction of the glass production rate and power consumption. The results show reasonable agreement with the melting rates measured during pilot-scale melter tests.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Effect of sucrose on technetium and rhenium retention during vitrification of low-activity wastes

Sucrose (C 12 H 22 O 11 ) has been used in low-activity waste (LAW) melter feeds containing large fractions of nitrates, nitrites, or both because it facilitates foam suppression and denitration. This study focused on the effect of sucrose in LAW feeds on technetium (Tc) and rhenium (Re) retention. The amount of sucrose added in feeds was varied to differentiate the carbon-to-nitrogen mole ratio (C/N ratio). The results show that larger sucrose addition (higher C/N ratio) enhances Tc and Re retention. Reducing conditions induced by sucrose decomposition and early chemical reactions between sucrose and NaNO 3 /NaNO 2 are expected to increase Tc and Re retention. However, high sucrose addition decreased sulfur (S) retention slightly because sodium sulfate decomposes in reducing conditions at lower temperature. This early sulfate decomposition can affect Tc and Re retention partly because these species can be soluble in sulfate phases. This correlation indicates that the decrease of sulfate phases in the glass by early decomposition can reduce the solubility of Tc and Re in the sulfate phases, which may increase Tc and Re retention in the glass. In addition, continuous gas evolution and vigorous foaming at the foaming temperature range of 700–900°C may influence Tc and Re retention process interrupting retention or facilitating volatilization.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Conversion kinetics during melting of simulated nuclear waste glass feeds measured by dissolution of silica

In this work, we experimentally investigated the batch-to-glass conversion kinetics of two low-activity and two high-level nuclear waste melter feeds that represent widely different behavior during melting; tests comprised thermogravimetric analysis, the feed expansion test, evolved gas analysis, and x-ray diffraction. Our study indicates that the conversion processes, which include gas-evolving reactions, dissolution of crystalline phases, and primary foam expansion and collapse, are interconnected and influenced by the feed’s thermal history. The fraction of dissolved silica was adopted as a measure of the extent of conversion inside the cold cap—the floating layer of feed material on the top surface of the melt in an electric melter. The interface between the cold cap and the free-flowing melt below was associated with a constant fraction of dissolved silica. The estimated viscosity of glass-forming melt at this interface lies within a narrow range for the feeds studied.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗