Engineering Papers⌕ Search

Engineering topics

Klein, James E.

Publications and source records attributed to Klein, James E..

Tritium Compatible Pump Development

Vacuum pumps are routinely discontinued for newer models, discontinued permanently, or manufacturers go out of business. It is necessary that new pump models and technologies are evaluated for tritium service, and even what can be done for pumps are not rated for tritium service to be re-engineered for tritium service.

Klein, James E.↗

Tritiated Water Disposition Strategies

Tritium, a radioactive isotope of hydrogen, is typically confined within one or more confinement barriers. Tritium readily reacts with oxygen to form tritiated water or can exchange with protium or deuterium atoms in water to create tritiated water which is around 10,000 times more toxic than elemental tritium. Primary tritium confinement systems can create small volumes of highly tritiated water. Secondary confinement systems, like inert gloveboxes, will produce larger volumes of lower concentration tritiated water. Much larger volumes of tritiated water of very low tritium content are produced by tritium permeation/diffusion. Tritium from inside primary and secondary confinement barriers will diffuse from these systems into cooling water systems. Closed loop, recirculating cooling water systems will slowly accumulate tritium and create concentrations which exceed drinking water (or permitted discharge) concentrations. The cooling water systems designed as series of interconnected cooling loops that can slowly transfer tritium from one cooling loop to another cooling loop through heat exchangers. These large volumes of tritiated water may be above federal discharge limits and also lack convenient disposition pathways. This document will discuss tritiated water management strategies from the perspective of large volume, low tritium concentrations that exceed drinking water or permitted discharge limits. Applicable US regulatory requirements for a Molybdenum-99 (Mo-99) production facility concerning tritiated water are also cited. Tritiated water disposition options, based on typical waste minimization strategies will guide dispositions options. A Case Study example is presented to illustrate the pros and cons of several disposition options. The report does not recommend any particular disposition pathway but discusses strategies to be explored by a producer to guide selection of processes which best fits the needs of a particular waste stream.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of Detritiation Strategies for Mitigating Tritium Releases

Tritium confinement is performed using different barriers to minimize releases to the environment. Primary confinement is usually performed by process piping and components, secondary confinement typically by inerted gloveboxes connected to a continuously operating tritium stripper system. Some facility designs employ tertiary tritium confinement by using process room confinement with a tritium stripper system activated after an accident to further mitigate tritium releases to the environment. Secondary confinement of some tritium systems such as radiation-hardened or shielded-cell enclosures are not easily achieved using designs for inerted glovebox. These enclosures can be challenging to seal for secondary tritium confinement due to heating, ventilation, and air conditioning (HVAC) needs for temperature control, as well as feedthroughs for equipment and instrumentation, are potential pathways for tritium leaks or loses. Additional tritium leak paths can be created in secondary confinement enclosures due to a Design Basis Accident (DBA) seismic event. These new, larger tritium leak rates from the DBA event are usually not part of the stripper system design basis so all tritium released to the secondary confinement enclosure is assumed released to the environment. Detritiation strategies for shielded enclosures and/or gloveboxes with significant leak rates are necessary to minimize off-site radiological dose consequences. To address this, the relationship between the confinement system leak rate and stripper system (recirculating) flow rate was evaluated to meet prescribed maximum allowable environmental tritium emissions from the event. The simple analysis described assumes a constant leak rate from the confinement system (i.e. shielded enclosure or glovebox) while a recirculating stripper system strips tritium from the system– a competition between tritium release and tritium recovery. At a high level, the resulting expression summarizes the relationship between system leak rate (F L ) and stripper flow rate (F S ) relative to allowable tritium release (Q A ) and initial tritium release (Q 0 ): $\frac{F_L}{F_s}$ ≈ $\frac{Q_A}{Q_0}$. This report derives the relationship between these parameters, examines the impact of finite stripping times followed by purging of the stripped volume. The analysis provides example results for up to 30 gram tritium releases: the maximum tritium inventory of a Hazard Category III (Department of Energy) Nuclear Facility. The detritiation model presented represents a high-level analysis of tritium recovery versus losses for “leaky” confinement enclosures such as shielded cells after large tritium releases. Key parameters for doing the analyses are the system leak rate, stripper flow rate, initial tritium release, and allowable tritium release values. The analyses show a proportional decrease in releases with reduction in initial tritium release but a non-linear increase in tritium recovery with increased stripper flow rate or reduced leak-rate. The analyses also apply to glovebox confinement systems which could have significant increases in leak rates after a DBA. The analysis recognizes but does not include tritium absorption followed by re-emission from the walls of the confinement volume – an analysis which could be pursued in future studies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal release of {sup 3}He from tritium aged LaNi{sub 4.25}Al{sub 0.75} hydride

The Savannah River Site Tritium Facilities (SRS-TF) utilizes LANA.75 (LaNi{sub 4.25}Al{sub 0.75})in the tritium process to store hydrogen isotopes. The vast majority of {sup 3}He born from the radioactive decay of tritium stored in LANA.75 is trapped in the hydride metal matrix. The SRS-TF has multiple LANA.75 tritium storage beds that have been retired from service with significant quantities of He-3 trapped in the metal. To support He-3 recovery, the Savannah River National Laboratory (SRNL) conducted thermogravimetric analysis coupled with mass spectrometry (TGA-MS) on a tritium aged LANA.75 sample. TGA-MS testing was performed in an argon environment. Prior to testing, the sample was isotopically exchanged with deuterium to reduce residual tritium and passivated with air to alleviate pyrophoric concerns associated with handling the material outside of an inert glovebox. Analyses indicated that gas release from this sample was bimodal, with peaks near 220 and 490 C. degrees. The first peak consisted of both {sup 3}He and residual hydrogen isotopes, the second was primarily {sup 3}He. The bulk of the gas was released by 600 Celsius degrees. (author)

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Adsorption Study of SF₆, H₂ And N₂ Over 13x Molecular Sieve

This is a short study on SF₆, H₂ and N₂ adsorption over 13X Molecular Sieve. It is confirmed that 13X can be used to remove SF₆. At cryogenic temperature, 13X adsorbs significant amount of H₂ which can be purged out with He or He with N₂ doses. The N₂ adsorption was not affected with preadsorbed H₂.

36 MATERIALS SCIENCE↗