Engineering Papers⌕ Search

Engineering topics

Kissinger, Ryan M.

Publications and source records attributed to Kissinger, Ryan M..

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Formulation and testing of a high-tin borosilicate nuclear waste glass for in-can melting

Here, borosilicate waste glasses were successfully developed to immobilize two high-level waste raffinate streams via an in-can melter process with an Inconel 601 canister at 1050 °C. Measured viscosity and crystallinity thermal profiles were within the targeted processing constraints for the in-can melter process. Measured chemical durability of the glass by ASTM C1285–21 (Method A), ranged from normalized loss of boron, NL(B) = 1.44 – 2.65 g•m -2 , and NL(B) decreased with increased waste loading, accompanied by increased SnO 2 crystallinity. Measured corrosion of the in-can melter canister by a glass melt showed that Inconel 601 performed well at 1100 °C for up to 500 hr. Resistance polarization measurements versus time revealed that Inconel 601 corrosion rates in (and by) glass melts decreased from an initial rate of 63 mm•y -1 down to 10.2 mm•y -1 after 137 h with increased duration, which was attributed to formation of an oxide passivation layer (mainly Cr 2 O 3 ) at the alloy-glass interface.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Low-Activity Waste Glass Standards Preparation and Characterization for Calibration of Analytical Instruments

A matrix of seven low-activity waste (LAW) glasses was fabricated and characterized to be used by the Hanford Waste Treatment and Immobilization Plant (WTP) as analytical instrument calibration and matrix interference standards when measuring LAW glass compositions. The matrix of glasses was designed to represent the range of LAW glass compositions that will be generated by the WTP. Samples from each of the seven glasses were measured with electron probe microanalysis (EPMA), ion chromatography (IC), and bulk inductively coupled plasma mass spectroscopy (ICP-MS) to determine the variability and accuracy across batches and within individually poured glass bar samples. High relative percent differences and standard deviations were calculated for components with low concentrations due to instrument detection limits. IC and ICP-MS percent differences and standard deviations were higher at low component concentrations. Otherwise, variability in measured compositions from IC and ICP-MS was generally lower than measurements from EPMA, with the exclusion of Cl, F, Si, and B. Overall, the two methods proved comparable and complementary. From EPMA, IC, and ICP-MS data, volatile elements were underrepresented compared to batched compositions, which suggested loss of these elements during melting. EPMA data was statistically analyzed to evaluate homogeneity within single bars and whole compositions for each of the seven glasses. Most of the variability within glass compositions occurred at the bar-to-bar level; however, no clear systematic trends were observed. Based on these analyses, when using these glasses as reference material, it is recommended that the overall mean and variance of each composition be used for performing instrument calibrations and analytical corrections.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Single-component-at-a-time variation study for glass-ceramic waste forms

Here, a 51-sample composition variation study was performed on glass-ceramic waste forms for a raffinate waste stream from aqueous reprocessing of used nuclear fuel containing high fractions of Mo, alkalis, alkaline earths (AEs), and rare earths (REs). The study was designed with a single-component-at-a-time variation approach off a centroid composition. The components that were varied included Al, B, Ca, Li, Mo, Na, REs, Si, Zr, and Others (containing minor components). Data analysis included crystallization curves, microstructure, and phase compositions. A number of components (i.e., Li 2 O, B 2 O 3 , REO x , MoO 3 , Na 2 O, and ZrO 2 ) significantly impacted the concentration and chemistry of phases, especially the primary phases of oxyapatite [i.e., Ca 2 RE 8 (SiO 4 ) 6 O 2 ] and powellite (i.e., AEMoO 4 ), precipitated in the slow-cool heat-treated waste forms; minor phases included cerianite [i.e., Ce x Zr (1-x) O 2 ], Ba-molybdate [i.e., Ba(Gd 0.67 Mo 0.33 O 3 ], noble metals, pollucite (i.e., CsAlSiO 4 ), and RE-borosilicate (i.e., RE 3 BSi 2 O 10 ).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Effects of Al:Si and (Al + Na):Si ratios on the properties of the international simple glass, part I: Physical properties

Understanding composition-structure-property relationships of high-alumina nuclear waste glasses are important for vitrification of nuclear waste at the Hanford Site. Two series of glasses were designed, one with varying Al:Si ratios and the other with (Al+Na):Si ratios based on the International Simple Glass (ISG, a simplified nuclear waste model glass), with Al2O3 ranging from 0 to 23 mol % (0 to 32 wt. %). The glasses were synthesized and characterized using electron probe microanalysis, X-ray photoelectron spectroscopy, small angle X-ray scattering, high temperature oxide melt solution calorimetry, and infrared spectroscopy. Glasses were crystal free, and the lowest Na2O and Al2O3 glass formed an immiscible glass phase. Evolution of various properties - glass transition temperature, percentage of 4-coordinated B, enthalpy of glass formation - and infrared spectroscopy results indicate that structural effects differ based on the glass series.

Nuclear Waste Glass↗