Engineering Papers⌕ Search

Engineering topics

Kirsten P Duffy

Publications and source records attributed to Kirsten P Duffy.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Static Testing of A Conductively-Cooled, High Temperature Superconducting Rotor for A 1.4 MW Electric Machine in a Thermal Vacuum Chamber

NASA’s high efficiency megawatt motor (HEMM) is a partially superconducting, 1.4 MW electric machine designed for electrified aircraft propulsion. HEMM’s high performance is enabled by a field winding composed of 2nd generation high temperature superconducting (HTS) coils that are designed to operate at temperatures below 62 K. The superconducting rotor is conductively cooled to cryogenic temperatures using a rotating cryocooler embedded inside the machine’s shaft. This paper presents a static test of the full-scale superconducting rotor in a thermal vacuum chamber. The experimental setup is described in detail. Thermal and electromagnetic 3D finite element analyses of the experimental setup are shown along with a comparison of the model results to model results for HEMM. The thermal response during cool down from room temperature is discussed. Electrical measurements are presented for operation at different dc current excitations up to the rated current of the rotor (57.2 A) and temperature limit of the HEMM design (62 K). The results suggest that minor damage to one superconducting coil occurred at 50 A and 61.2 K, causing increased resistance in the system, but that the system could still be stably operated at 57.2 A and 62 K when conductively cooled by a cryocooler.

electrified aircraft propulsion↗
NASA NTRS2020

Status of Analysis and Manufacturability of Superconducting Wires with Low AC Losses

Superconductors can carry an order-of-magnitude higher current than room temperature copper wires and can do so with two orders-of-magnitude lower alternating current (AC) electrical losses. These advantages underlie our estimates that turboelectric propulsion of large aircraft can be enabled by superconducting machines. However, even the much smaller losses of superconductors pose thermal management issues at the low temperatures required for superconductivity, and predicting those losses and validating the predictions has been a developing process at NASA Glenn Research Center over the last decade. Since Glenn’s earliest assessments of the feasibility of fully superconducting machines for turboelectric propulsion, the available models of AC losses in superconductors have changed significantly, as well as the state of development of superconducting wire for the coils of electric machines. While the models available to us have improved significantly, the value of the AC losses predicted by these models have only increased as more fidelity was developed. The fabrication of medium temperature superconducting wires (Tc near 40 K) has advanced, and wires can be produced with finer filaments and tighter twisting than a decade ago. However, the ideal wire configurations, developed decades ago for low temperature superconductors (Tc < 25 K), still elude manufacturers of medium and high temperature (Tc > 77 K) superconductors. This report discusses the developments, the current limitations, and the expectations that future configurations of superconducting wire can yet be produced that will provide suitably low AC losses for the aircraft propulsion application. The report presents a basic discussion of the types of AC losses in superconductors, followed by a discussion of the evolution of our understanding of the practical consequences of those AC losses. Next, there is a discussion of the superconducting wire configurations that have been developed, which were partially guided by that understanding. A brief discussion of the modes of removing the heat produced by the losses is presented. Lastly, a comparison is presented between losses in currently available MgB2 wire and other important cases, including copper at room temperature, copper at liquid hydrogen temperature, and expected future MgB2 wire. Room temperature copper has 100 times the loss of today’s MgB2 and 300 times the expected loss of future MgB2. That implies we can expect much higher efficiency from fully superconducting machines than from machines with copper stators, and high efficiency targets remain the driver behind investment in MgB2 development and medium temperature superconductor research.

superconducting motors↗
NASA NTRS2004

Self-Tuning Impact Damper for Rotating Blades

A self-tuning impact damper is disclosed that absorbs and dissipates vibration energy in the blades of rotors in compressors and/or turbines thereby dramatically extending their service life and operational readiness. The self-tuning impact damper uses the rotor speed to tune the resonant frequency of a rattling mass to an engine order excitation frequency. The rating mass dissipates energy through collisions between the rattling mass and the walls of a cavity of the self-tuning impact damper, as well as though friction between the rattling mass and the base of the cavity. In one embodiment, the self-tuning impact damper has a ball-in-trough configuration with tire ball serving as the rattling mass.

Kirsten P Duffy↗
NASA NTRSDate not supplied

Dynamic Bellows for a Pulse Tube Cryocooler Application

Electrified aircraft propulsion systems will require powertrain components that are both lightweight and highly efficient. NASA’s 1.4 MW High Efficiency Megawatt Motor (HEMM) has been designed to run at 6800 RPM with >98% efficiency and 16 kW/kg, achieving low losses by incorporating a cryocooler within its rotor shaft to cool superconducting DC windings. A pulse-tube cryocooler typically contains an oscillating piston that drives acoustic waves; however, leakage around the piston reduces the efficiency of the cryocooler. A metal bellows was designed to replace the piston to allow for little to no leakage. The requirements for this bellows were extreme in terms of displacement amplitude, oscillating pressure amplitude, temperature, and frequency. It was determined that an off-the-shelf edge-welded bellows would not work for this application, so a custom bellows was designed to include full convolutions welded only on their outer diameters where the stress is lower. Several high-fatigue-strength materials were considered, including 17-4PH H900 and Aermet 100. The final bellows design includes 74 convolutions with a variable inner diameter that helps distribute and reduce the dynamic stress throughout the length rather than concentrating the high stress in one location. To test the concept, a short 10-convolution bellows with constant inner diameter was designed for testing. One short bellows test article was fabricated with the outer diameter weld, and one by 3D printing. Both will be fatigue-tested with the goal of achieving 10^7 cycles.

Bellows↗
NASA NTRSDate not supplied

Cryogenic Vacuum Chamber Testing of A Conductively-Cooled, High Temperature Superconducting Rotor for a 1.4 MW Electric Machine for Aeronautics Applications

This paper presents the first ever demonstration of a superconducting rotor cooled conductively without a cryogenic fluid or solid. The full-scale rotor was operated statically in its intended environment – about 1e-3 torr vacuum with only conductive cooling through mechanical connections to a cryocooler contained on the rotor. Stable operation of the rotor in a representative magnetic environment was demonstrated up to its rated direct current (57.2 A) and the designed temperature limit for the superconductor (62 K). Additional electrical measurements increased confidence that the superconducting coils functioned as intended. A collection of steady state temperature distributions was measured at operating and non-operating conditions. In all but one case, the observed temperature gradient between the cold tip and superconducting coils satisfies the design but with little margin. Opportunities to reduce the gradient are identified.

Electrified aircraft propulsion↗
NASA NTRSDate not supplied

Design Implications of Rotordynamics and Mass Balancing on a 1.4 MW Partially Superconducting Machine

To ensure that rotating machines operate without excessive bearing loads, vibration, and dynamic stresses, their design must consider rotordynamic response and provisions for mass balancing of rotors, even when their rotational speeds are modest. This paper presents a rotordynamics design study for a 1.4 MW, partially superconducting electric machine proposed for electrified aircraft propulsion – NASA’s High Efficiency Megawatt Motor (HEMM). The study includes the selection of mass balancing grade and mount and bearing stiffnesses to yield satisfactory critical speeds, deflection, and unbalance force, and predictions of the expected mass unbalance caused by the superconducting rotor coils. The impact of the machine’s number of rotor poles on expected mass unbalance is also quantified. Design decisions and lessons learned are discussed.

hybrid electric aircraft↗
NASA NTRSDate not supplied

Design Implications of Rotordynamics and Mass Balancing on a 1.4 MW Partially Superconducting Machine

To ensure that rotating machines operate without excessive bearing loads, vibration, and dynamic stresses, their design must consider rotordynamic response and provisions for mass balancing of rotors, even when their rotational speeds are modest. This paper presents a rotordynamics design study for a 1.4 MW, partially superconducting electric machine proposed for electrified aircraft propulsion – NASA’s High Efficiency Megawatt Motor (HEMM). The study includes the selection of mass balancing grade and mount and bearing stiffnesses to yield satisfactory critical speeds, deflection, and unbalance force, and predictions of the expected mass unbalance caused by the superconducting rotor coils. The impact of the machine’s number of rotor poles on expected mass unbalance is also quantified. Design decisions and lessons learned are discussed.

hybrid electric aircraft↗