Engineering Papers⌕ Search

Engineering topics

King, Ryan

Publications and source records attributed to King, Ryan.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

MADE3D: Enabling the next generation of high-torque density wind generators by additive design and 3D printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments—especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technolgies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

17 WIND ENERGY↗
DOE OSTI2021

MADE3D: Enabling the Next-Generation High-Torque- Density Wind Generators by Additive Design and 3D Printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments - especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technologies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

3D printing↗
DOE OSTI2021

Flow Redirection and Induction in Steady State (FLORIS) Wind Plant Power Production Data Sets

This dataset contains turbine- and plant-level power outputs for 252,500 cases of diverse wind plant layouts operating under a wide range of yawing and atmospheric conditions. The power outputs were computed using the Gaussian wake model in NREL's FLOw Redirection and Induction in Steady State (FLORIS) model, version 2.3.0. The 252,500 cases include 500 unique wind plants generated randomly by a specialized Plant Layout Generator (PLayGen) that samples randomized realizations of wind plant layouts from one of four canonical configurations: (i) cluster, (ii) single string, (iii) multiple string, (iv) parallel string. Other wind plant layout parameters were also randomly sampled, including the number of turbines (25-200) and the mean turbine spacing (3D-10D, where D denotes the turbine rotor diameter). For each layout, 500 different sets of atmospheric conditions were randomly sampled. These include wind speed in 0-25 m/s, wind direction in 0 deg.-360 deg., and turbulence intensity chosen from low (6%), medium (8%), and high (10%). For each atmospheric inflow scenario, the individual turbine yaw angles were randomly sampled from a one-sided truncated Gaussian on the interval 0 deg.-30 deg. oriented relative to wind inflow direction. This random data is supplemented with a collection of yaw-optimized samples where FLORIS was used to determine turbine yaw angles that maximize power production for the entire plant. To generate this data, a subset of cases were selected (50 atmospheric conditions from 50 layouts each for a total of additional 2,500 cases) for which FLORIS was re-run with wake steering control optimization. The IEA onshore reference turbine, which has a 130 m rotor diameter, a 110 m hub height, and a rated power capacity of 3.4 MW was used as the turbine for all simulations. The simulations were performed using NREL's Eagle high performance computing system in February 2021 as part of the Spatial Analysis for Wind Technology Development project funded by the U.S. Department of Energy Wind Energy Technologies Office. The data was collected, reformatted, and preprocessed for this OEDI submission in May 2023 under the Foundational AI for Wind Energy project funded by the U.S. Department of Energy Wind Energy Technologies Office. This dataset is intended to serve as a benchmark against which new artificial intelligence (AI) or machine learning (ML) tools may be tested. Baseline AI/ML methods for analyzing this dataset have been implemented, and a link to their repository containing those models has been provided. The .h5 data file structure can be found in the GitHub repository under explore_wind_plant_data_h5.ipynb.

AI↗
DOE OSTI2021

Multi-Fidelity Active Subspaces for Wind Farm Uncertainty Quantification

Wind plants operate in stochastic environments characterized by complex turbulent flow dynamics and high-dimensional random variables. A key step in uncertainty quantification studies is sensitivity analysis and dimension reduction that can facilitate the development of surrogate models to be used for forward and inverse propagation or optimization under uncertainty. Prior work has shown active subspaces are an effective tool for identifying important directions in the space of stochastic inputs; however, they have only been applied to single-fidelity wind plant models. In this study, we investigate the efficacy of a multi-fidelity active subspace method for analyzing the uncertainty in wind plant power output. The multi-fidelity active subspace estimator offers the promise of increased accuracy in identifying active subspaces as compared to a single-fidelity estimator for the same computational cost, or a reduction in cost for the same accuracy. This makes the study of uncertainty in larger wind plants and with higher fidelity physics tractable. The multi-fidelity active subspace method is applied to gridded and existing wind plant layouts with single and multiple inflow conditions and its performance for surrogate modeling and uncertainty propagation is compared against a single-fidelity active subspace method. This multi-fidelity approach yields substantial computational speedups of 2x - 3.4x across the test cases along with acceptable accuracy in surrogate modeling and computing statistical moments.

active subspace↗
DOE OSTI2020

A fluid-structure interaction solver for investigating torsional galloping in solar-tracking photovoltaic panel arrays

Solar-tracking photovoltaic arrays are susceptible to aeroelastic fluttering during high-wind events. This dynamic fluttering behavior can grow in amplitude until the panels enter an unstable mode known as torsional galloping which can lead to panel failure or total array destruction. To better understand the physics of the torsional galloping phenomenon and to inform the discussion around panel design and recommended panel stow positions during high wind events, a fluid-structure interaction solver composed of a simulated atmospheric boundary layer with simplified panel structural responses was designed. The simulation choices and features of this solver were informed by the geometry and physical properties of an experimental panel array known to exhibit torsional galloping behavior during hind-wind events. Furthermore, these simulations revealed that the torsional galloping instability is driven by a combination of cyclic vortex shedding from the sun-facing side of the panel and the elastic properties of the torque tube linking the panel assemblies. Testing different stow angles across a range of wind speeds indicates that panels are generally more stable when stowed at negative angles where the leading edge is closer to the ground, hypothesized to be due to ground-blocking effects. These results are supplemented by a discussion of stability trends noted during testing and possible implications when considering multi-row array interactions.

14 SOLAR ENERGY↗
DOE OSTI2020

Deep learning for in situ data compression of large turbulent flow simulations

As the size of turbulent flow simulations continues to grow, in situ data compression is becoming increasingly important for visualization, analysis, and restart checkpointing. For these applications, single-pass compression techniques with low computational and communication overhead are crucial. In this paper we present a deep-learning approach to in situ compression using an autoencoder architecture that is customized for three-dimensional turbulent flows and is well suited for contemporary heterogeneous computing resources. The autoencoder is compared against a recently introduced randomized single-pass singular value decomposition (SVD) for three different canonical turbulent flows: decaying homogeneous isotropic turbulence, a Taylor-Green vortex, and turbulent channel flow. Our proposed fully convolutional autoencoder architecture compresses turbulent flow snapshots by a factor of 64 with a single pass, allows for arbitrarily sized input fields, is cheaper to compute than the randomized single-pass SVD for typical simulation sizes, performs well on unseen flow configurations, and has been made publicly available. The results reported here show that the autoencoder dramatically outperforms a randomized single-pass SVD with similar compression ratio and yields comparable performance to a higher-rank decomposition with an order of magnitude less compression in regard to preserving a number of important statistical quantities such as turbulent kinetic energy, enstrophy, and Reynolds stresses.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

A Fluid Solver for Studying Torsional Galloping in Solar-Tracking PV Panel Arrays

Solar-tracking photovoltaic arrays are susceptible to aeroelastic fluttering during high-wind events. This dynamic fluttering behavior can grow in amplitude until the panels enter an unstable mode known as torsional galloping which can lead to panel failure or total array destruction. To better understand the physics of the torsional galloping phenomenon, and to inform the discussion around panel design and recommended panel stow positions during high wind events, a fluid-structure interaction solver composed of a simulated atmospheric boundary layer with simplified panel structural responses was designed. The simulation choices and features of this solver were informed by the geometry and physical properties of an experimental panel array known to exhibit torsional galloping behavior during hind-wind events. These simulations revealed that the torsional galloping instability is driven by a combination of cyclic vortex shedding from the sun-facing side of the panel and the elastic properties of the torque tube linking the panel assemblies. Testing different stow angles across a range of wind speeds indicates that panels are generally more stable when stowed at negative angles where the leading edge is closer to the ground, hypothesized to be due to ground-blocking effects.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

An Unsteady Actuator Line Solver to Enable Adjoint Sensitivity Studies for Wake Steering

This study demonstrates the sensitivity of wind turbine wake steering performance to blade design. An actuator line model was implemented within an unsteady adjoint solver that enables efficient execution of gradient-based optimization and sensitivity studies. After first confirming the feasibility of wake steering by controlling actuator line chord profiles and formulating a suitable objective function for wake position, a sensitivity study was conducted to determine the relative importance of chord length as a function of spanwise position on the resulting turbine wake deflection. The results presented here support the idea that blade design choices play a role in wake control. In a larger context, this study demonstrates a computational framework in which turbine and blade designs can be studied at the individual and farm-wide level to enhance wind plant controllability and manage power output.

17 WIND ENERGY↗
DOE OSTI2020

Uncertainty Quantification for Capacity Expansion Planning

This report quantifies the uncertainty in output decisions from a Capacity Expansion Planning (CEP) model. The need to understand how uncertainties within CEP models and modeling assumptions affect Quantities of Interest (QoIs) such as expansion and operating costs, as well as expansion decisions remains an ongoing challenge in scientific research and industrial operations. This area of research is particularly important for models which seek to capture how large networks will evolve and operate under increased sources of variable generation, i.e., higher penetration of renewable technologies such as solar and wind generators. Uncertainty quantification (UQ) of CEP models which estimate expansion costs and decisions, and production cost models which estimate operating costs and dispatch decisions, is a key focus of research at NREL. The Regional Energy Deployment System (ReEDS) represents a state-of-the-art CEP model and considers a range of possible grid evolutions in an attempt to identify key drivers, ramifications, and decisions which contribute to better informed investment and policy decisions. However, research to quantify how uncertainties and model assumptions, such as unit commitment (UC), within ReEDS may be affecting its outputs remains challenging due to to size and complexity of the model

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Chapter 14: Machine Learning of Combustion LES Models from Reacting Direct Numerical Simulation

In this chapter we demonstrate how supervised deep learning techniques can be used to construct models for the filtered progress variable source term necessary for large eddy simulation (LES). The source data for the model is a direct numerical simulation (DNS) of a reacting flow in a low swirl burner configuration. Filtered quantities taken from the DNS data are used to train a deep neural network (DNN)-based model. An efficient data sampling strategy was devised to ensure that a uniform representation of all the states observed in the filtered DNS data are equally present in the training dataset. A-priori testing of the DNN-based model highlights the representative power of DNN to accurately reproduce the filtered reaction progress variable source term over a range of scales and various flame regimes as seen in an industrial burner.

combustion LES models↗
DOE OSTI2020

Opportunities for Research and Development of Hybrid Power Plants

Hybrid power plants show promise to provide significant value to the electric grid system especially as shares of renewable energy in systems increase from 10% to 20% or more. Many manufacturers and developers are proactively developing hybrid power plant strategies to ensure plant profitability in markets where it’s important to provide energy that is more predictable and controllable, with higher capacity values, as well as various ancillary services to the grid system. However, there still are many questions around if and when hybrid power plants make sense versus leaving it to the larger grid system to ensure low cost and reliable supply by engaging directly with all individual assets. This report summarizes literature on the state-of-the-art in research concerning hybrid power plants from multiple perspectives including: 1) resource and market opportunities, 2) technology selection and sizing, 3) physical design, and 4) operation and control. The emphasis was placed on wind and solar hybrid power plants (with or without storage) but additional technologies were briefly considered and merit further investigation.

17 WIND ENERGY↗
DOE OSTI2020

Wind Farm Simulation and Layout Optimization in Complex Terrain: Preprint

This work reports on incorporating complex terrain into wind farm simulations for the purpose of layout optimization. Adding complex terrain boundary conditions to NREL's medium fidelity computational fluid dynamics model, WindSE, produces significant separation, flow curvature, and speedup effects that would otherwise be difficult to capture with lower-fidelity models or a flat-terrain assumption. These flow features, in turn, can significantly impact the optimal turbine array layout. We demonstrate the impact of complex terrain on flow in both an idealized and real-world setting, and discuss modifications to the code that enable gradient-based optimization using terrain-aware adjoint gradients. Through several optimization case studies, we show that the layout optimization process takes advantage of speedup effects on terrain high points, and leverages flow curvature effects that modify wake trajectories. This yields substantial power improvements over gridded layouts, and hints at future research directions in simulation and optimization for wake trajectories in complex terrain.

17 WIND ENERGY↗
DOE OSTI2018

A Systematic Approach to Offshore Wind Turbine Jacket Pre-Design and Optimization: Geometry, Cost, and Surrogate Structural Code Check Models

The main obstacles in preliminary design studies or optimization of jacket substructures for offshore wind turbines are high numerical expenses for structural code checks and simplistic cost assumptions. In order to create a basis for fast design evaluations, this article provides the following: firstly, a jacket model is proposed that covers topology and tube sizing with a limited set of design variables. Secondly, a cost model is proposed that goes beyond the simple and common mass-dependent approach. And thirdly, the issue of numerical efficiency is addressed by surrogate models both for fatigue and ultimate limit state code checks. In addition, this work shows an example utilizing all models. The outcome can be utilized for preliminary design studies and jacket optimization schemes and is suitable for scientific and industrial applications.

17 WIND ENERGY↗
DOE OSTI2017

WindSE: Wind Systems Engineering [SWR-17-03]

WindSE is a tool for modeling atmospheric fluid flow within a wind plant and performing optimization of the turbine positions or operating settings. WindSE is a python package that uses a FEniCS backend to perform wind farm simulations and optimization.

King, Ryan↗