Engineering Papers⌕ Search

Engineering topics

Kim, H. C.

Publications and source records attributed to Kim, H. C..

Strong QCD from Hadron Structure Experiments

The topical workshop Strong QCD from Hadron Structure Experiments took place at Jefferson Lab from November 6–9, 2019. Impressive progress in relating hadron structure observables to the strong QCD mechanisms has been achieved from the ab initio QCD description of hadron structure in a diverse array of methods in order to expose emergent phenomena via quasi-particle formation. The wealth of experimental data and the advances in hadron structure theory make it possible to gain insight into strong interaction dynamics in the regime of large quark–gluon coupling (the strong QCD regime), which will address the most challenging problems of the Standard Model on the nature of the dominant part of hadron mass, quark–gluon confinement, and the emergence of the ground and excited state hadrons, as well as atomic nuclei, from QCD. This workshop aimed to develop plans and to facilitate the future synergistic efforts between experimentalists, phenomenologists, and theorists working on studies of hadron spectroscopy and structure with the goal to connect the properties of hadrons and atomic nuclei available from data to the strong QCD dynamics underlying their emergence from QCD. These results pave the way for a future breakthrough extension in the studies of QCD with an Electron–Ion Collider in the U.S.

Brodsky, S. J.↗

A study on the assessment criteria of DHC in PWR spent fuel

One of the major degradation mechanisms of PWR spent fuel cladding is delayed hydride cracking (DHC), which can activate within a relatively low temperature range. Its maximum crack growth rate is estimated to be within the range of 10{sup -7} m/s, at which the cladding can rupture in 1 to 2 years during dry storage. For this reason, it is essential to prevent DHC crack growth itself, but most of the existing DHC studies have been focused on the crack growth rate. In this regard, the values and characteristics of the threshold stress intensity factor (K{sub IH}) for PWR Zircaloy-4 cladding were described. Based on the limited existing test results and analysis, the experimentally measured K{sub IH} were compared with the predicted K{sub IH}. The comparison shows that the predicted values are much lower than the measured ones and both theoretical estimation and measured values of K{sub IH} increase as the temperature increases. The possibilities of degradation by DHC were also discussed during long-term dry storage. For a more reliable analysis, additional information on a pre-existing crack of spent fuel is needed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of effective-stress-function algorithm for nuclear fuel simulation

In a pressurized water reactor (PWR), the mechanical integrity of nuclear fuel is the most critical issue as it is an important barrier for fission products released into the environment. The integrity of zirconium cladding that surrounds uranium oxide can be threatened during off-normal operation owing to a pellet-cladding mechanical interaction (PCMI). To analyze the fuel and cladding behavior during off-operation, the fuel performance code should calculate an inelastic analysis in two - or three-dimensional calculations. In this paper, the effective stress function (ESF) algorithm based on a two-dimensional FE module has been implemented to simulate the inelastic behavior of the cladding with stability and accuracy. The ESF algorithm solves the governing equations of the inelastic constitutive behavior by calculating the zero of the appropriate effective-stress-function. To verify the accuracy of the ESF algorithm for an inelastic analysis, a code-to-code benchmark was performed using the commercial FE code, ANSYS 13.0. To demonstrate the stability and convergence of the implemented algorithm, the number of iterations in the ESF algorithm was compared with that in a sequential algorithm in the case of an inelastic problem. Consequently, the evaluation results demonstrate that the implemented ESF algorithm improves the efficiency of the computation without a loss of accuracy for an inelastic analysis. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Detection rate evaluation of ex-core detectors in the subcritical OPR-1000 reactor

The OPR-1000 is a PWR reactor developed in Korea. One-type ex-core detectors for monitoring of power distributions were installed in the OPR-1000 reactor to alternate the three-types of the ex-core detectors. For the verification of the detection performances, neutron transport calculation was performed by using MCNP5 code. The reaction rate in the ex-core detectors and the neutron flux were evaluated by using MCNP5 code as changing the boron concentration from 1800 ppm to 1122 ppm in the subcritical condition. The reaction rate results in fission chamber show that minimum and maximum values are 0.03577 and 3.33563 reactions/cm{sup 3}-sec, respectively. This study can be directly used for the verification and improvement of fission chamber performance in using one-type ex-core detector. Also, it can be utilized for the production of the reference data in determining neutron source strength. It is expected the proposed simulation method can be utilized to the improvement of the dose monitoring system. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗