Comparison of Measured and Simulated Acoustic Signatures for a Full-Scale Aircraft with and Without Airframe Noise Abatement
No abstract available
Khorrami, Mehdi R.↗
Engineering topics
Khorrami, Mehdi R.
Publications and source records attributed to Khorrami, Mehdi R..
Assessment of Airframe Noise Reduction Technologies Based on EPNL from Flight Tests
The acoustic performance of various airframe noise reduction technologies – Adaptive Compliant Trailing Edge flap, main landing gear fairings, and gear cavity treatments – was determined, individually and in combination, using the Effective Perceived Noise Level metric. These noise measurements and calculations closely follow the Federal Aviation Administration aircraft noise certification standards, specifically for the approach noise measurement point. The flyover data correspond to pole-mounted, single-microphone measurements obtained during a series of flight tests, conducted under the NASA Flight Demonstrations and Capabilities project, that evaluated flap and landing gear noise reduction technologies. To minimize contributions from the propulsion system, the aircraft was flown along the approach path with engine thrust set at ground idle. Although contamination from engine, background, and secondary airframe noise sources partially masked the true performance of the tested technologies, the resulting acoustic data clearly showed substantial noise reductions relative to baseline levels. The acoustic benefits measured by the single microphones are consistent with previously reported trends in acoustic levels obtained from phased microphone array data.
Ravetta, Patricio A.↗
Simulation-Based Assessment of a Full-Scale Installed Quiet Landing Gear
Full-scale simulations of a Gulfstream G-III aircraft, performed in support of the NASA Acoustic Research Measurements flights, are presented to complement results discussed in earlier studies. The flow solver employed in those studies, Dassault Systèmes’ lattice Boltzmann PowerFLOW®, was also used during this investigation to conduct time-dependent simulations of the entire aircraft in landing configuration with a fully dressed landing gear. The high-fidelity simulations, performed at a Mach number of 0.23 and a Reynolds number of 10.5 × 106 based on mean aerodynamic chord, captured all relevant airframe noise sources. The computations were used to assess the aeroacoustic performance of the main landing gear, with and without noise reduction fairings installed, of a G-III aircraft equipped with Adaptive Compliant Trailing Edge technology and conventional Fowler flaps. To facilitate comparison of predicted noise signatures with effective perceived noise levels obtained from flight test measurements, the “as-flown” nose landing gear geometry, missing in our earlier studies, was added to the simulated G-III aircraft configurations. The high fidelity, synthetic data were post-processed using a Ffowcs-Williams and Hawkings integral approach to estimate farfield acoustic behavior, with pressures on the model solid surface or pressure and velocity components on a permeable surface enveloping the acoustic near field used as input.
Duda, Benjamin↗
Flight-Test Evaluation of Landing Gear Noise Reduction Technologies
Results from the third Acoustics Research Measurements flight test, conducted under the NASA Flight Demonstrations and Capabilities project, are presented and discussed. The test evaluated landing gear and gear cavity noise mitigation technologies installed on a NASA Gulfstream G-III. Aircraft configurations with and without main landing gear treatments were flown at several flap deflections to determine the acoustic performance of the technologies for aircraft equipped with conventional Fowler flaps. With the aircraft flying an approach path and engines at “ground-idle,” extensive acoustic measurements were acquired with a phased microphone array system. Computed beamform maps were used to examine the effectiveness of the tested technologies in reducing the strength of the noise sources generated by the main landing gear. Various integration regions were devised to extract the farfield noise spectra associated with the treated and untreated landing gear configurations. Analyses of the gathered acoustic data demonstrate that significant noise reduction was achieved. How- ever, the full noise reduction potential of the technologies could not be determined because of contamination from flap inboard edge noise and other secondary sources.
Khorrami, Mehdi R.↗
Measured and Simulated Acoustic Signature of a Full-Scale Aircraft with Airframe Noise Reduction Technology Installed
Microphone phased-array and pole-mounted microphone data gathered during the NASA Acoustics Research Measurements flight tests were used to benchmark results from companion full-scale aeroacoustics simulations. Conducted with the lattice Boltzmann solver PowerFLOW®, the simulations predicted the acoustic behavior of various tested aircraft configurations. Emphasis was placed on those flown during the third flight test - a Fowler flap-equipped Gulfstream G-III with and without noise abatement technology on the main landing gear. Direct comparisons between experimental and synthetic microphone phasedarray data were achieved by applying the same processing and deconvolution technique to both sets of data. To extend the validation of the computations to the metric used for noise certification, the Effective Perceived Noise Level, a high-fidelity digital model of the nose landing gear, which was excluded from earlier computations, was developed and integrated into the G-III aircraft geometry. The acoustic study presented here demonstrates that the simulated beamform maps and corresponding integrated farfield spectra accurately predict the locations and strengths of the prominent airframe noise sources present on the G-III aircraft.
Khorrami, Mehdi R.↗
Method for Cavity Noise Reduction
A stretchable mesh material extends across the opening of a cavity of the landing gear of an aircraft when the landing gear is in the deployed position. The mesh material alters the flow of air across the opening of the landing gear cavity and significantly reduces the amount of noise produced by the wheel well at low-to-mid frequencies.
Khorrami, Mehdi R.↗
Optical Geolocation for Small Unmanned Aerial Systems
This paper presents an airborne optical geolocation system using four optical targets to provide position and attitude estimation for a sUAS supporting the NASA Acoustic Research Mission (ARM), where the goal is to reduce nuisance airframe noise during approach and landing. A large precision positioned microphone array captures the airframe noise for multiple passes of a Gulfstream III aircraft. For health monitoring of the microphone array, the Acoustic Calibration Vehicle (ACV) sUAS completes daily flights with an onboard speaker emitting tones at frequencies optimized for determining microphone functionality. An accurate position estimate of the ACV relative to the array is needed for microphone health monitoring. To this end, an optical geolocation system using a downward facing camera mounted to the ACV was developed. The 3D positioning of the ACV is computed using the pinhole camera model. A novel optical geolocation algorithm first detects the targets, then a recursive algorithm tightens the localization of the targets. Finally, the position of the sUAS is computed using the image coordinates of the targets, the 3D world coordinates of the targets, and the camera matrix. A Real-Time Kinematic GPS system is used to compare the optical geolocation system.
Dolph, Chester V.↗
Simulations of a Full-Scale Aircraft with Installed Airframe Noise Reduction Technologies
Computational results are presented for a high-fidelity, full-scale, full-span Gulfstream G-III aircraft model equipped with flap and main landing gear (MLG) noise reduction technologies. The simulations, which were conducted in support of a NASA airframe noise flight test campaign of the same technologies, use the lattice Boltzmann solver PowerFLOW® to capture time-accurate flow data with sound propagation to the far field accomplished using a Ffowcs-Williams and Hawkings (FWH) acoustic analogy approach. The aerodynamic and aeroacoustic behavior of the aircraft were investigated in the approach configuration with combinations of flap and landing gear deployments. The simulated flap concept is an Adaptive Compliant Trailing Edge (ACTE) flap that replaces the Fowler flap system on the G-III aircraft. The simulated MLG noise reduction concept is comprised of porous fairings and a collection of other smaller fairings fitted around the flow-facing components. Using the Fowler flap results as a reference, comparisons are presented on the noise reduction effectiveness of the ACTE flap system. Investigations were made on the effects of using the porous fairings and ACTE flap as noise reduction concepts in tandem. The ACTE flap was found to reduce the total airframe noise level at all flap deflection angles when compared to the Fowler flap equipped model. As anticipated, a reduction in aerodynamic performance was also found when the ACTE flap system was used. The MLG fairings were shown to further reduce the total airframe noise level of the G-III.
Ferris, Ryan J.↗
Analysis of Simulated and Experimental Noise Sources of Boeing 777 Main Gear Model via CLEAN in 3D
Previously obtained experimental and simulated phased microphone array data for the NASA 26%-scale model of a six-wheel main landing gear, with and without a toboggan-shaped noise reduction fairing, were analyzed using the CLEAN technique in three dimensions. The model is a high-fidelity representation of the Boeing 777-200 aircraft main landing gear. The reprocessing of the acoustic data was undertaken to address the deficiencies encountered in the source localization (beamform) maps and the integrated farfield spectra at mid to high frequencies in our previous study, where conventional array processing techniques were applied to the same data sets. Application of the CLEAN approach resulted in higher quality beamform maps with many of the previously observed side lobes either eliminated or suppressed significantly. As a result, integration of the experimentally and computationally based maps showed substantial improvement in the quality of the high-frequency spectral content relative to the corresponding spectra generated via conventional array processing, thus extending the good agreement achieved between the measured and predicted farfield spectra from 8 kHz to 14 kHz in model-scale frequencies. In addition, an examination of the simulated surface pressure fluctuations, off-surface flow field, and three-dimensionally constructed noise sources was conducted to determine the cause of the subtle discrepancies between measured and predicted sound pressure levels that occur in the 1,800 Hz to 4,000 Hz model-scale frequency range.
Ravetta, Patricio↗
Airframe Noise Simulations of a Full-Scale Aircraft
Computational results for a full-scale simulation of a Gulfstream G-III aircraft are presented. In support of a NASA airframe noise flight test campaign, Exa Corporation’s lattice Boltzmann PowerFLOW® solver was used to perform time-accurate simulations of the flow around a highly detailed, full-scale aircraft model. Free-air boundary conditions were used at a Mach number of 0.23 and a Reynolds number of 10.5 × 10(exp 6) based on mean aerodynamic chord. This paper documents the simulation campaign for the baseline aircraft configuration at several flight conditions, including multiple flap deflections and main landing gear deployed or retracted. The high-fidelity, synthetic data were post-processed using a Ffowcs-Williams and Hawkings integral approach to estimate farfield acoustic behavior, with pressures on the model solid surface or a permeable surface enveloping the acoustic near field used as input. The numerical approach, simulation attributes, and the effects of grid resolution, gear deployment, and multiple flap deflections, are discussed as well.
Appelbaum, Jason↗
Flight-Test Evaluation of Airframe Noise Mitigation Technologies
A series of flight tests targeting airframe noise reduction was planned and executed under the NASA Flight Demonstrations and Capabilities project. The objectives of the tests were two-fold: to evaluate the aeroacoustic performance of several noise reduction technologies in a relevant environment and to generate a comprehensive database for advancing the state of the art in simulation-based airframe noise prediction methodologies. These technologies – an Adaptive Compliant Trailing Edge flap, main landing gear fairings, and gear cavity treatments – were integrated on a NASA Gulfstream G-III aircraft to determine their effectiveness, both on a component-level (individually) and a system-level (combined) basis. With the aircraft flying an approach pattern and the engines set at ground idle, extensive acoustic measurements were acquired using a phased microphone array system. Detailed analyses of the gathered acoustic data clearly demonstrate that significant noise reduction was achieved for the flap and main landing gear components.
Khorrami, Mehdi R.↗
Assessment of Noise Reduction Concepts for Leading-Edge Slat Noise
The leading-edge slat of a high-lift airfoil can be a significant noise contributor during aircraft landing. This paper summarizes the effects of several passive noise reduction devices on the 30P30N high-lift airfoil. Experiments are conducted on a two-dimensional multi-element high-lift airfoil with leading-edge slat extensions, gap filler, and cove filler in an anechoic wind tunnel to evaluate the effect of passive flow control on the acoustics generated by the unsteady flow field. Slat geometry modifications associated with the treatments alter the flow field in the region that dominates the generation of the acoustic field. Three angles of attack (a(k) = 8°, 10°, and 15.5°) and three different Reynolds numbers (Re(c) = 1.2e6, 1.5e6, and 1.71e6) are selected as the test conditions. Steady surface pressure measurements are conducted to assess the effect of the treatments on the lift and drag. Unsteady surface pressure measurements along with the far-field acoustic array measurements are performed to evaluate the changes in near- and far-field pressure fluctuations, respectively. Delay and Sum (DAS) beamforming method is applied to locate the noise sources on the model and provide integrated spectra. Implementation difficulties with the gap filler led to structural integration deficiencies that prevented a fair assessment of this technology. Among the other passive devices, the cove filler s the most effective noise reduction, along with a negligible change in the aerodynamic metrics.
Zhang, Yang↗
Aeroacoustic Simulations of a Nose Landing Gear with FUN3D: A Grid Refinement Study
A systematic grid refinement study is presented for numerical simulations of a partially-dressed, cavity-closed (PDCC) nose landing gear configuration that was tested in the University of Florida's open-jet acoustic facility known as the UFAFF. The unstructured-grid flow solver FUN3D is used to compute the unsteady flow field for this configuration. Mixed-element grids generated using the Pointwise (Registered Trademark) grid generation software are used for numerical simulations. Particular care is taken to ensure quality cells and proper resolution in critical areas of interest in an effort to minimize errors introduced by numerical artifacts. A set of grids was generated in this manner to create a family of uniformly refined grids. The finest grid was then modified to coarsen the wall-normal spacing to create a grid suitable for the wall-function implementation in FUN3D code. A hybrid Reynolds-averaged Navier-Stokes/large eddy simulation (RANS/LES) turbulence modeling approach is used for these simulations. Time-averaged and instantaneous solutions obtained on these grids are compared with the measured data. These CFD solutions are used as input to a FfowcsWilliams-Hawkings (FW-H) noise propagation code to compute the farfield noise levels. The agreement of the computed results with the experimental data improves as the grid is refined.
Vatsa, Veer N.↗
Evaluation of Methods for In-Situ Calibration of Field-Deployable Microphone Phased Arrays
Current field-deployable microphone phased arrays for aeroacoustic flight testing require the placement of hundreds of individual sensors over a large area. Depending on the duration of the test campaign, the microphones may be required to stay deployed at the testing site for weeks or even months. This presents a challenge in regards to tracking the response (i.e., sensitivity) of the individual sensors as a function of time in order to evaluate the health of the array. To address this challenge, two different methods for in-situ tracking of microphone responses are described. The first relies on the use of an aerial sound source attached as a payload on a hovering small Unmanned Aerial System (sUAS) vehicle. The second relies on the use of individually excited ground-based sound sources strategically placed throughout the array pattern. Testing of the two methods was performed in microphone array deployments conducted at Fort A.P. Hill in 2015 and at Edwards Air Force Base in 2016. The results indicate that the drift in individual sensor responses can be tracked reasonably well using both methods. Thus, in-situ response tracking methods are useful as a diagnostic tool for monitoring the health of a phased array during long duration deployments.
Humphreys, William M.↗
A Comparative Study of Simulated and Measured Main Landing Gear Noise for Large Civil Transports
Computational results for the NASA 26%-scale model of a six-wheel main landing gear with and without a toboggan-shaped noise reduction fairing are presented. The model is a high-fidelity representation of a Boeing 777-200 aircraft main landing gear. A lattice Boltzmann method was used to simulate the unsteady flow around the model in isolation. The computations were conducted in free-air at a Mach number of 0.17, matching a recent acoustic test of the same gear model in the Virginia Tech Stability Wind Tunnel in its anechoic configuration. Results obtained on a set of grids with successively finer spatial resolution demonstrate the challenge in resolving/capturing the flow field for the smaller components of the gear and their associated interactions, and the resulting effects on the high-frequency segment of the farfield noise spectrum. Farfield noise spectra were computed based on an FWH integral approach, with simulated pressures on the model solid surfaces or flow-field data extracted on a set of permeable surfaces enclosing the model as input. Comparison of these spectra with microphone array measurements obtained in the tunnel indicated that, for the present complex gear model, the permeable surfaces provide a more accurate representation of farfield noise, suggesting that volumetric effects are not negligible. The present study also demonstrates that good agreement between simulated and measured farfield noise can be achieved if consistent post-processing is applied to both physical and synthetic pressure records at array microphone locations.
Konig, Benedikt↗
On the Importance of Spatial Resolution for Flap Side Edge Noise Prediction
A spatial resolution study of flap tip flow and the effects on the farfield noise signature for an 18%-scale, semispan Gulfstream aircraft model are presented. The NASA FUN3D unstructured, compressible Navier-Stokes solver was used to perform the highly resolved, time-dependent, detached eddy simulations of the flow field associated with the flap for this high-fidelity aircraft model. Following our previous work on the same model, the latest computations were undertaken to determine the causes of deficiencies observed in our earlier predictions of the steady and unsteady surface pressures and off-surface flow field at the flap tip regions, in particular the outboard tip area, where the presence of a cavity at the side-edge produces very complex flow features and interactions. The present results show gradual improvement in steady loading at the outboard flap edge region with increasing spatial resolution, yielding more accurate fluctuating surface pressures, off-surface flow field, and farfield noise with improved high-frequency content when compared with wind tunnel measurements. The spatial resolution trends observed in the present study demonstrate that the deficiencies reported in our previous computations are mostly caused by inadequate spatial resolution and are not related to the turbulence model.
Mineck, Raymond E.↗
Stretchable Mesh for Cavity Noise Reduction
A stretchable mesh material extends across the opening of a cavity of the landing gear of an aircraft when the landing gear is in the deployed position. The mesh material alters the flow of air across the opening of the landing gear cavity and significantly reduces the amount of noise produced by the wheel well at low-to-mid frequencies.
Khorrami, Mehdi R.↗
Simulation-Based Airframe Noise Prediction of a Full-Scale, Full Aircraft
A previously validated computational approach applied to an 18%-scale, semi-span Gulfstream aircraft model was extended to the full-scale, full-span aircraft in the present investigation. The full-scale flap and main landing gear geometries used in the simulations are nearly identical to those flown on the actual aircraft. The lattice Boltzmann solver PowerFLOW® was used to perform time-accurate predictions of the flow field associated with this aircraft. The simulations were performed at a Mach number of 0.2 with the flap deflected 39 deg. and main landing gear deployed (landing configuration). Special attention was paid to the accurate prediction of major sources of flap tip and main landing gear noise. Computed farfield noise spectra for three selected baseline configurations (flap deflected 39 deg. with and without main gear extended, and flap deflected 0 deg. with gear deployed) are presented. The flap brackets are shown to be important contributors to the farfield noise spectra in the mid- to high-frequency range. Simulated farfield noise spectra for the baseline configurations, obtained using a Ffowcs Williams and Hawkings acoustic analogy approach, were found to be in close agreement with acoustic measurements acquired during the 2006 NASA-Gulfstream joint flight test of the same aircraft.
Khorrami, Mehdi R.↗