Engineering topics
Publications and source records attributed to Khandavalli, Sunilkumar.
Steady-shear rheology showing evolution of the microstructure of iridium oxide catalyst inks of PEM water electrolyzers with aging time.
Not Available
Not Available
Abstract We investigate the effect of alcohol fraction (isopropanol, IPA) in a binary water‐alcohol solvent mixture on the shear and extensional rheological properties, as well as the role of viscoelasticity on fiber formation of poly(acrylic acid) (PAA) in electrospinning. Comparison of the scaling of both specific viscosities η sp and extensional relaxation times λ E of PAA in water–IPA mixtures, showed stronger scaling compared to salt‐free aqueous polyelectrolyte solutions, except for the η sp in the unentangled regime displaying a polyelectrolyte‐like scaling η sp ~ c 0.5 for all IPA%. Such deviation suggested IPA induces association/aggregation of PAA. However, the trends between η sp and λ E magnitudes as a function of IPA% differ for concentrations compared in the entangled regime. The η sp as well as their elastic moduli exhibit a maximum, whereas λ E increases monotonically with IPA%, suggesting a complex interplay of various interactions are dictating their structure in water‐IPA mixtures, affecting their shear and extensional response differently. Electrospinning experiments showed increasing IPA% reduces the onset of both beaded and uniform fibers. Analysis using dimensionless numbers indicated the enhancement of their elasticity by IPA, and the consequent stabilizing effect on their jets/filaments against break‐up during electrospinning, plays a role in the improvement of their fiber formation.
Leveraging the interactions between ionomer and catalyst can increase the performance of proton exchange membrane fuel cells. The impacts of the equivalent weight (EW) of perfluorosulfonic acid–based ionomers on the platinum group metal-free electrode structure and fuel cell performance have not been fully explored. Four membrane electrode assemblies (MEAs) were prepared by using a commercial Fe–N–C catalyst, two perfluorosulfonic acid ionomers with different EWs, that is, Aquivion 720 (A720) and Nafion 1100 (N1100), and two ionomer-to-catalyst (I/C) ratios. The four MEAs were characterized to understand the impact of the ionomer EW and content on the capacitance, proton conductivity, and mass transport on the cathode. The mass transport resistance was measured for the first time using a new oxygen reduction reaction limiting current method enabling to couple the effects of oxygen diffusion with liquid water generation. Low EW ionomer combined with a moderate I/C results in improved performance due to its enhanced proton conductivity. However, when used at high I/C, it can cause severe water flooding at high current density due to the enhanced liquid water uptake, especially at high relative humidity, resulting in lower catalyst utilization and higher mass transport resistance.
Explore the source record for details and available documents.
We investigate the effect of the poly(acrylic acid) (PAA) carrier polymer concentration on the microstructure and rheological properties of catalyst inks for electrospun polymer–electrolyte membrane fuel-cell catalyst layers. Characterization of an ink microstructure using oscillatory shear rheology showed that the catalyst particles (platinum on carbon) are significantly agglomerated in the absence of PAA or an ionomer. Both the ionomer and PAA promoted the stability of the particles against agglomeration via electrosteric stabilization by adsorbing onto the particle surface. Increasing the PAA concentration increased the stability of the particles (or reduced the agglomerated structure) due to increasing PAA coverage onto the free surface area of the particles. However, beyond a certain increase in concentration, PAA was found to predominantly remain as an excess free polymer in the ink due to an insufficient free/available surface area on the particles for further PAA coverage. Extensional rheology measurements demonstrated that PAA enhances the extensional viscosities of the inks. Consequently, increasing the PAA concentration in the ink promoted the evolution of uniform nanofibers. However, beyond a certain concentration, a significant increase in the shear viscosities of the inks led to defective fiber morphologies because of the onset of flow instabilities. Electrochemical performance comparisons between catalyst layers with different PAA concentrations showed maximum performance at the PAA concentration that led to the least agglomerated structure of the catalyst, most uniform fiber morphologies, and low concentrations of free (non-adsorbing) PAA in the electrode. These results provide a rationale for optimization of electrospun catalyst nanofibers for both spinnability and electrochemical performance.
This work investigates how local ionomer/platinum (Pt) interactions and ionomer distribution in electrospun Pt/Vulcan nanofiber electrodes impact ionomer coverage, proton accessibility, and oxygen reduction reaction (ORR) performance in proton-exchange membrane fuel cells. Insights from various in situ electrochemical diagnostics were utilized in conjunction with ex situ microscopic characterization to understand how the electrode microstructure—both at the aggregate level and near the ionomer/platinum interface—is affected by electrospinning in comparison to ultrasonic spraying. The effect of the carrier polymer poly(acrylic acid) (PAA) concentration from 5–20 wt % (with respect to total ink solids) on the resulting nanofiber morphology is discussed. Electron microscopy observations and CO displacement measurements indicated that Pt/Vulcan nanofibers prepared with a higher PAA concentration (15 wt %) were conformally coated with a film of ionomer on the exterior of the fiber, which resulted in an overall lower ionomer coverage on both Pt and carbon throughout the fiber diameter. In contrast, 10 wt % PAA leads to a uniform intrafiber distribution of the ionomer within the fibers, increasing the overall ionomer coverage and proton accessibility under both wet and dry conditions. These differences in the local ionomer coverage on Pt between 10 and 15 wt % PAA were also attributed to differences in the adsorption/interaction affinities between PAA and the ionomer onto the catalyst surface in the ink using zeta potential measurements. Additional fuel cell electrochemical tests on the electrospun electrodes show improvements in ORR kinetics and high-current-density H 2 /air performance compared to the ultrasonically sprayed electrodes.
In this paper, we present an investigation of the microstructure and rheological behavior of catalyst inks consisting of Fe–N–C platinum group metal-free catalysts and a perfluorosulfonic acid ionomer in a dispersion medium (DM) of water and 1-propanol ( n PA). The effects of the ionomer-to-catalyst (I/C) ratio and weight percentage of water (H 2 O %) in the DM on the ink microstructure were studied. Steady-shear and dynamic-oscillatory-shear rheology, in combination with synchrotron X-ray scattering, was utilized to understand interparticle interactions and the level of agglomeration of the inks. In the absence of the ionomer, the inks were significantly agglomerated, approaching a gel-like microstructure for catalyst concentrations as low as 2 wt %. The effect of H 2 O % in the DM on particle agglomeration was found to vary with particle concentration. In concentrated inks (≥2 wt % catalyst), increasing H 2 O % was found to increase agglomeration because of the hydrophobic nature of the catalysts. In dilute inks (<1 wt % catalyst), the trend was reversed with increasing H 2 O %, suggesting that electrostatic interactions are dominating the behavior. In inks with 5 wt % catalyst, the addition of an ionomer was found to significantly stabilize the catalyst against agglomeration. Maximum stability was observed at 0.35 I/C for all DM H 2 O % studied. At high ionomer concentrations (I/C > 0.35), interesting differences were observed between n PA-rich inks (H 2 O % ≤ 50%) and H 2 O-rich (82% H 2 O) inks. The n PA-rich inks remained predominantly stable—ink viscosity only weakly increased with I/C and the Newtonian behavior was maintained for I/C up to 0.9. In contrast, the H 2 O-rich inks exhibited a significant increase in viscoelasticity with increasing I/C, suggesting flocculation of the catalyst by the ionomer. These differences suggest that the nature of the interactions between the ionomer and catalyst is highly dependent on the H 2 O % in the DM.
With lower site density and turnover frequency, platinum group metal (PGM)-free catalysts based electrodes are often greater than 50 mu m thick in order to increase performance across the fuel cell operating range. Consequently, PGM-free electrodes have an additional bulk electrode transport resistance beyond the local or aggregate level transport in thin platinum-based electrodes. In parallel to the development of more active and durable PGM-free catalysts, advancements in understanding the interplay between PGM-free electrode fabrication, bulk-electrode transport, proton conductivity and performance are needed. Here, the relationship between ionic and gas phase transport through the electrode thickness is modified by adjusting electrocatalyst and ionomer flocculation/interaction at the ink level. The influence of the ink composition (water/n-propanol content) is examined via various in-situ electrochemical and ex-situ characterization techniques and the resulting electrode structure/performance relationship contrasted with electrode performance robustness across a range of relative humidity (RH). For the electrocatalyst examined here, a water-rich (82 wt% H2O) ink formulation was favorable for operation at high RH due to improved molecular diffusion through larger electrode pores. In contrast, the improved interactions between ionomer and electrocatalyst enabled a more robust electrode and higher performance during low RH operation for the 50 wt% H2O content ink.